시간에 따라 농도 분포가 변하는 비정상 상태 확산은 Fick의 제2법칙으로 기술된다. 반무한 매체에서의 해는 오차 함수(error function)로 표현되며, 침투 깊이는 $\sqrt{D_{AB}t}$에 비례한다. 이 해석이 Higbie의 침투 이론(penetration theory)의 기초가 된다.Unsteady-state diffusion, where concentration profiles change with time, is governed by Fick's second law. The solution for a semi-infinite medium is expressed using the error function, with penetration depth proportional to $\sqrt{D_{AB}t}$. This analysis forms the basis of Higbie's penetration theory.
Fick's 2nd LawError FunctionPenetration DepthFourier Mass NumberHigbie's Theory
Section 13.1
Fick의 제2법칙과 비정상 확산Fick's Second Law and Transient Diffusion
Fick의 제2법칙은 종 연속 방정식에서 대류를 무시하고 반응이 없는 1차원 확산에 대한 편미분 방정식이다. 초기 조건과 경계 조건에 따라 다양한 해를 갖는다. 가장 기본적인 경우인 반무한 매체(semi-infinite medium)에서, 표면 농도가 갑자기 $C_s$로 바뀌면 오차 함수 해를 얻는다.Fick's second law is the PDE for 1D diffusion without convection or reaction, derived from species continuity. It admits various solutions depending on initial and boundary conditions. For the most basic case of a semi-infinite medium with a sudden surface concentration change to $C_s$, the error function solution is obtained.
반무한 매체: 한쪽 표면에서만 확산이 시작되고, 반대쪽은 무한히 먼 경우. $x \to \infty$에서 $C_A = C_{A,0}$ (초기 농도)Semi-infinite medium: diffusion starts from one surface; the other end is infinitely far. $C_A = C_{A,0}$ (initial concentration) as $x \to \infty$
Q1. 비정상 확산에서, 확산 시간을 4배로 늘리면 침투 깊이(concentration front)는 약 몇 배 깊어지는가?Q1. In transient diffusion, if diffusion time is quadrupled, by what factor does the penetration depth increase?
상사 변수 $\eta = x/(2\sqrt{D_{AB}t})$에서 같은 $\eta$ 값(같은 농도 도달)을 위한 깊이 $x \propto \sqrt{t}$이다. 따라서 시간을 4배로 하면 침투 깊이는 $\sqrt{4} = 2$배이다. 이는 확산이 시간의 제곱근으로만 진행됨을 보여준다. 확산은 거리가 커질수록 급격히 느려지는 과정이다.From the similarity variable $\eta = x/(2\sqrt{D_{AB}t})$, achieving the same $\eta$ (same concentration level) requires $x \propto \sqrt{t}$. Quadrupling time gives $\sqrt{4}=2$x depth. This shows diffusion progresses only as the square root of time -- it is inherently slow.
Section 13.2
침투 이론 (Penetration Theory)Penetration Theory
Higbie의 침투 이론은 비정상 확산 해석을 대류 물질 전달에 적용한 것이다. 유체 요소가 계면에 접촉 시간 $t_c$ 동안 머물면서 표면으로부터 확산을 받는다고 모델링한다. 시간 평균 플럭스로부터 물질 전달 계수를 유도하면 $k_c = 2\sqrt{D_{AB}/(\pi t_c)}$를 얻는다. 확산 계수의 1/2승에 비례한다는 것이 정체막 이론($k_c \propto D_{AB}$)과 다른 점이다.Higbie's penetration theory applies the unsteady diffusion analysis to convective mass transfer. A fluid element contacts the interface for a contact time $t_c$, receiving diffusion from the surface. The time-averaged flux yields the mass transfer coefficient $k_c = 2\sqrt{D_{AB}/(\pi t_c)}$. The key difference from film theory ($k_c \propto D_{AB}$) is the half-power dependence on diffusivity.
$$ \text{Fo}_m = \frac{D_{AB}\,t}{L^2} \quad \text{(Fourier mass number)} $$
$\text{Fo}_m$: 질량 Fourier 수. 확산에 의해 스케일 $L$까지 농도가 전파되는 정도를 나타낸다. $\text{Fo}_m \gtrsim 0.2$이면 확산이 전체 스케일에 도달한다$\text{Fo}_m$: mass Fourier number. Indicates how far concentration has propagated over scale $L$ by diffusion. $\text{Fo}_m \gtrsim 0.2$ means diffusion reaches the full scale
침투 깊이: $\delta_p \approx \sqrt{\pi D_{AB} t}$. 농도가 표면값의 약 1%까지 변화하는 깊이Penetration depth: $\delta_p \approx \sqrt{\pi D_{AB} t}$. Depth where concentration changes to ~1% of surface value
아래 그림은 반무한 매체에서의 비정상 확산을 보여준다. Fourier 질량 수 $\text{Fo}_m = D_{AB}t/L^2$를 변경하면 시간이 지남에 따라 농도 프로파일이 매체 깊숙이 침투하는 과정을 관찰할 수 있다. 표면($x=0$)에서 $C_A = C_s$이고, 깊은 곳에서는 초기 농도 $C_0$를 유지한다.The figure below shows transient diffusion into a semi-infinite medium. Adjusting the Fourier mass number $\text{Fo}_m = D_{AB}t/L^2$ shows how the concentration profile penetrates deeper into the medium over time. At the surface ($x=0$), $C_A = C_s$; deep inside, $C_A$ remains at the initial $C_0$.
Interactive Figure 13.1반무한 매체에서의 비정상 확산: C(x,t)Transient Diffusion in Semi-Infinite Medium -- C(x,t)
Q2. 탄소강의 침탄(carburizing) 공정에서, 표면 탄소 농도가 일정하게 유지될 때 1mm 깊이에 원하는 탄소 농도를 달성하는 데 4시간이 걸렸다. 2mm 깊이에 같은 농도를 달성하려면 약 몇 시간이 필요한가?Q2. In carburizing of steel with constant surface carbon concentration, if 4 hours are needed to reach the desired carbon level at 1mm depth, how long is needed for the same level at 2mm depth?
같은 농도 비($\theta = \text{erf}(\eta)$가 같음)를 위해서는 $\eta = x/(2\sqrt{D_{AB}t})$가 일정해야 한다. $x_2/x_1 = 2$이면 $\sqrt{t_2/t_1} = 2$, 즉 $t_2 = 4 t_1 = 16$시간. 확산에 의한 침투 깊이가 $\sqrt{t}$에 비례하므로, 두 배 깊이를 달성하려면 네 배의 시간이 필요하다.For the same concentration ratio ($\theta = \text{erf}(\eta)$ constant), $\eta = x/(2\sqrt{D_{AB}t})$ must be constant. If $x_2/x_1 = 2$, then $\sqrt{t_2/t_1} = 2$, so $t_2 = 4t_1 = 16$ hours. Since penetration depth scales as $\sqrt{t}$, doubling the depth requires quadrupling the time.
Interactive Figure 13.2침탄 깊이와 온도, 시간Carburizing Furnace: Setting Case Depth with T and t
예측: 같은 온도에서 가열 시간을 2배로 늘리면 케이스 깊이(C = 0.4 %인 위치)는 몇 배가 될까?Predict: At fixed T, if the furnace time is doubled, by what factor does the case depth (position where C = 0.4 %) grow?
목표: 온도 한도 950 ℃ 안에서 케이스 깊이를 1.00 mm부터 1.06 mm까지로 맞추고 가열 시간은 최소로 하세요 (온도 940 ℃ 이상). 아래 패드의 점을 끌어 시간(가로)과 온도(세로)를 정하세요.Goal: Within the 950 ℃ limit, make a case depth of 1.00 to 1.06 mm in the shortest time (T of 940 ℃ or higher). Drag the handle in the pad below: time (horizontal), temperature (vertical).
DAB (m²/s)--
케이스 깊이 (mm)Case depth (mm)--
이 온도에서 1 mm에 필요한 시간 (h)Time for 1 mm at this T (h)--
깊이는 $\sqrt{D_{AB}t}$에 비례하므로 시간을 2배로 하면 1.41배만 깊어지고, 확산계수가 Arrhenius 식으로 커지는 온도 상승이 시간 단축에 훨씬 효과적이다.Depth scales with $\sqrt{D_{AB}t}$, so doubling the time deepens the case only 1.41 times, while raising T (D follows Arrhenius) shortens the cycle far more effectively.
Interactive Figure 13.3젖은 평판의 건조: 송풍 속도와 두께Drying of a Wet Slab: Air Velocity and Thickness
예측: 송풍 팬을 최대로 올리면 평판은 항상 더 빨리 마를까?Predict: Does turning the fan to maximum always dry the slab faster?
목표: 6 h에서 평균 수분을 초기값의 10 % 이하로 낮추고, 같은 시각에 표면 수분은 5 % 이상으로 유지해 균열을 막으세요. 왼쪽 팬을 위아래로 끌어 풍속을, 평판 오른쪽 핸들을 좌우로 끌어 두께를 바꾸세요.Goal: At 6 h, bring the average moisture to 10 % of its initial value or less while keeping surface moisture at 5 % or more to avoid cracking. Drag the fan up/down for air velocity and the right-hand grip left/right for thickness.
Bim = hma/DAB--
6 h 평균 수분Average moisture at 6 h--
6 h 표면 수분Surface moisture at 6 h--
Bim이 커지면 표면 저항이 없어지고 건조 속도는 내부 확산이 정하므로, 팬을 더 세게 해도 평균 수분은 줄지 않고 표면만 먼저 말라 균열 위험이 커진다.Once Bim is large the surface resistance vanishes and internal diffusion sets the drying rate, so a stronger fan no longer lowers the average moisture but dries only the surface and raises the cracking risk.
Interactive Figure 13.4평판 중심 농도 차트 읽기: Fom과 BimSlab Chart Navigator: Fom and Bim
예측: Fom = 0.5에서 Bim을 100까지 올리면 중심의 무차원 농도 θ0는 0.2 아래로 내려갈까?Predict: At Fom = 0.5, if Bim is raised to 100, does the dimensionless center concentration θ0 fall below 0.2?
목표: 차트 위를 끌어 Fom = 0.5 (±0.05)에서 중심 농도 θ0 = 0.50 (±0.03)이 되는 Bim을 찾으세요. 가로로 끌면 Fom이, 세로로 끌면 Bim이 바뀝니다 (위쪽이 큰 값입니다).Goal: Drag on the chart to find the Bim that gives θ0 = 0.50 (±0.03) at Fom = 0.5 (±0.05). Horizontal drag sets Fom, vertical drag sets Bim (up is larger).
Fom--
Bim--
θ0 = (C0,center - C∞)/(Ci - C∞)--
Bim이 약 10을 넘으면 곡선이 거의 겹치므로 표면 저항은 무시할 수 있고, 같은 Fom에서 더 낮은 농도를 얻으려면 시간이나 두께를 바꿔야 한다.Above Bim of about 10 the curves nearly coincide, so surface resistance can be ignored; a lower concentration at the same Fom requires changing time or thickness.