이진 혼합물에서의 정상 상태 분자 확산은 두 가지 경계 조건에 따라 구분된다. 등몰 역확산(equimolar counter-diffusion, EMD)에서는 농도 분포가 선형이고, 일방 확산(unimolecular diffusion, UMD, 정체막 모델)에서는 정체 성분의 존재로 인해 농도 분포가 대수(logarithmic) 곡선이 된다.Steady-state molecular diffusion in a binary mixture is classified by two boundary conditions. In equimolar counter-diffusion (EMD), the concentration profile is linear. In unimolecular diffusion (UMD, stagnant film model), the presence of a stagnant component creates a logarithmic concentration profile.
등몰 역확산은 $N_A = -N_B$인 경우이다. 증류탑에서 응축과 증발이 동시에 일어나는 상황이 대표적이다. 이 조건에서 순 몰 유동(bulk flow)이 영이 되어 대류 보정항이 사라지고, 농도 분포는 순수한 Fick 확산에 의한 선형 프로파일이 된다.Equimolar counter-diffusion occurs when $N_A = -N_B$. A typical example is simultaneous condensation and evaporation in a distillation column. Under this condition, the net molar flow (bulk flow) is zero, the convective correction vanishes, and the concentration profile becomes a linear Fickian profile.
EMD에서 순 몰 유동 $(N_A + N_B) = 0$이므로 대류 보정 불필요In EMD, net molar flow $(N_A + N_B) = 0$, so no convective correction needed
$N_A$는 농도 차이와 확산 계수에 비례하고, 확산 경로 길이에 반비례$N_A$ is proportional to concentration difference and diffusivity, inversely proportional to path length
열전달 유사: $q = k(T_1 - T_2)/L$ (평판 전도)와 동일한 형태Heat transfer analogy: same form as $q = k(T_1 - T_2)/L$ (plane wall conduction)
Section 12.2
일방 확산 / 정체막 모델 (UMD)Unimolecular Diffusion / Stagnant Film Model (UMD)
일방 확산(UMD)은 한 성분만 이동하고 다른 성분은 정체(stagnant)하는 경우이다($N_B = 0$). 액체 표면에서의 증발이 전형적인 예이다. 정체 성분 B가 확산을 방해하므로 A의 순 플럭스에 대류 보정(drift flux)이 추가되어, 농도 분포가 EMD의 선형이 아닌 대수 곡선이 된다. 이때 대수 평균 농도(log-mean)가 중요한 역할을 한다.Unimolecular diffusion (UMD) occurs when only one component moves while the other is stagnant ($N_B = 0$). Evaporation from a liquid surface is a typical example. The stagnant component B impedes diffusion, adding a convective correction (drift flux) to the net flux of A. The concentration profile becomes logarithmic rather than linear, and the log-mean concentration becomes essential.
대류 보정(drift flux): $N_B = 0$이므로 $N_A = -cD_{AB}\frac{dx_A}{dz}\cdot\frac{1}{1-x_A}$. 분모 $(1-x_A)$가 대류 보정항Drift flux correction: since $N_B = 0$, $N_A = -cD_{AB}\frac{dx_A}{dz}\cdot\frac{1}{1-x_A}$. The $(1-x_A)$ denominator is the drift correction
$x_A \ll 1$ (희석 용액)이면 $(1-x_A) \approx 1$이 되어 EMD와 동일한 선형 프로파일로 수렴When $x_A \ll 1$ (dilute solution), $(1-x_A) \approx 1$ and the profile converges to the EMD linear profile
UMD 플럭스는 항상 EMD보다 크다: 같은 조건에서 $N_A^{\text{UMD}} / N_A^{\text{EMD}} = 1/y_{B,\text{lm}} > 1$UMD flux is always larger than EMD: $N_A^{\text{UMD}} / N_A^{\text{EMD}} = 1/y_{B,\text{lm}} > 1$ under the same conditions
Q1. 물이 공기 중으로 증발할 때, 공기는 정체 성분이다. 물 표면의 수증기 몰분율이 $y_{A1}=0.02$이고 자유 흐름에서 $y_{A2}=0$이면, 이 상황은 EMD에 가까운가 UMD에 가까운가?Q1. When water evaporates into air, air is the stagnant component. If water vapor mole fraction is $y_{A1}=0.02$ at the surface and $y_{A2}=0$ in the freestream, is this closer to EMD or UMD?
증발에서 공기(B)는 액체에 녹지 않으므로 $N_B = 0$인 UMD이다. 그러나 $y_A = 0.02 \ll 1$이므로 $y_{B,\text{lm}} \approx 0.99$이고, UMD 보정 $1/y_{B,\text{lm}} \approx 1.01$로 EMD와의 차이가 1% 수준이다. 슬라이더에서 $x_{A,s}$를 높이면 이 차이가 커지는 것을 확인할 수 있다.In evaporation, air (B) does not dissolve into the liquid, so $N_B = 0$ (UMD). However, $y_A = 0.02 \ll 1$ gives $y_{B,\text{lm}} \approx 0.99$, and the UMD correction $1/y_{B,\text{lm}} \approx 1.01$ differs from EMD by only ~1%. Increasing $x_{A,s}$ with the slider shows this difference growing.
Section 12.3
EMD vs UMD 비교 시각화EMD vs UMD Comparison Visualization
아래 그림에서 EMD(등몰 역확산)의 선형 농도 분포와 UMD(일방 확산)의 대수 농도 분포를 비교할 수 있다. 슬라이더로 총 압력, 막 두께, 표면 몰분율을 변경하고, 두 모드를 토글하여 차이를 관찰한다. $x_{A,s}$가 커질수록 UMD와 EMD의 차이가 뚜렷해진다.The figure below compares the linear concentration profile of EMD with the logarithmic profile of UMD. Adjust total pressure, film thickness, and surface mole fraction with sliders, and toggle between modes to observe differences. As $x_{A,s}$ increases, the UMD-EMD difference becomes more pronounced.
Interactive Figure 12.1정체막 확산: EMD vs UMD 농도 프로파일Stagnant Film Diffusion: EMD vs UMD Concentration Profile
P (atm)1.0 atm
δ (mm)5.0 mm
xA,s0.50
NA (EMD)--
NA (UMD)--
UMD/EMD--
EMD (선형)EMD (linear)
UMD (대수 곡선)UMD (logarithmic)
Q2. 표면 몰분율 $x_{A,s}$를 0.1에서 0.9로 올렸을 때, UMD/EMD 플럭스 비는 어떻게 변하는가?Q2. When surface mole fraction $x_{A,s}$ increases from 0.1 to 0.9, how does the UMD/EMD flux ratio change?
UMD/EMD = $1/y_{B,\text{lm}}$이다. $x_{A,s}$가 높아지면 $y_B = 1 - y_A$가 작아지고 $y_{B,\text{lm}}$이 감소하므로 비율이 커진다. 슬라이더를 움직여 확인할 수 있다. $x_{A,s} = 0.1$일 때 비율 ≈ 1.05이고, $x_{A,s} = 0.9$일 때는 비율이 크게 증가한다. 이는 정체 성분이 적을수록 대류 보정이 커짐을 보여준다.UMD/EMD = $1/y_{B,\text{lm}}$. As $x_{A,s}$ increases, $y_B = 1-y_A$ decreases, $y_{B,\text{lm}}$ decreases, and the ratio grows. Check with the slider: at $x_{A,s} = 0.1$ the ratio is ≈ 1.05, while at $x_{A,s} = 0.9$ it increases dramatically. This shows that less stagnant component means larger convective correction.
Interactive Figure 12.2Stefan 관: 증발 속도로 DAB 측정Stefan Tube: Measuring DAB from the Evaporation Rate
예측: 정체 공기 속을 위로 확산하는 증기의 몰분율 $y_A$는 액면에서 관 위쪽 끝까지 어떤 모양으로 줄어들까?Predict: How does the vapor mole fraction $y_A$ fall from the liquid surface to the open top through the stagnant air?
목표: 측정한 증발 플럭스 $N_A$와 $T$, $L$, $p_A^*$로 $N_A=\dfrac{D_{AB}P}{RTL}\ln\dfrac{P}{P-p_A^*}$을 풀어 $D_{AB}$를 구하고, 아래 추정값을 오차 10% 안으로 맞춘 뒤 제출하세요. 액면을 끌어 $L$을 바꾸고 온도 슬라이더로 $p_A^*$를 바꿔 가며 측정을 두 번 이상 하세요.Goal: Solve $N_A=\dfrac{D_{AB}P}{RTL}\ln\dfrac{P}{P-p_A^*}$ for $D_{AB}$ from the measured flux, $T$, $L$ and $p_A^*$, then set the estimate below within 10% and submit. Drag the liquid surface to change $L$ and use the temperature slider to change $p_A^*$; measure at least twice.
온도 TTemperature T25 °C
DAB 추정값DAB estimate0.050 cm²/s
L (cm)--
pA* (atm)--
NA (mmol/m²s)--
UMD/EMD--
증기가 위로 흐를 때 공기는 정지해 있어야 하므로 전체 흐름이 증기 확산을 돕고, 프로파일은 직선보다 위로 휘며 같은 구동력에서 플럭스가 EMD보다 $1/y_{B,\text{lm}}$배 크다.Because the air must stay at rest, bulk flow helps carry the vapor upward, so the profile bows above the straight line and the flux is $1/y_{B,\text{lm}}$ times the EMD value.
Interactive Figure 12.3촉매 알갱이 단면: Thiele 계수와 유효 계수Catalyst Pellet Cross-section: Thiele Modulus and Effectiveness Factor
예측: 알갱이를 두껍게 하면 알갱이 내부 촉매는 표면 농도 대비 더 잘 쓰일까, 덜 쓰일까?Predict: If the pellet is made thicker, is its interior catalyst used better or worse?
목표: 유효 계수 $\eta$를 0.80 이상 0.84 이하로 맞추세요. 이 범위가 이 $k$에서 $\eta\ge0.8$을 지키는 가장 두꺼운 알갱이입니다. 알갱이 오른쪽 끝을 끌어 두께를 바꾸고, $k$를 낮추면 더 두꺼운 알갱이가 가능한지도 확인하세요.Goal: Set the effectiveness factor $\eta$ between 0.80 and 0.84, which is the thickest pellet that keeps $\eta\ge0.8$ at this $k$. Drag the right edge of the pellet to change its thickness, and check whether a lower $k$ allows a thicker pellet.
반응 속도 상수 kRate constant k4.0 s⁻¹
2L (mm)--
Thiele φ--
η--
ccenter/cs--
$\phi=L\sqrt{k/D_e}$가 1보다 커지면 반응물이 중심에 닿기 전에 소모되어 안쪽 촉매가 쓰이지 않고, $\eta=\tanh\phi/\phi$는 $\phi$에 반비례해 떨어진다.When $\phi=L\sqrt{k/D_e}$ exceeds 1, reactant is consumed before reaching the center, the inner catalyst sits idle, and $\eta=\tanh\phi/\phi$ falls roughly as $1/\phi$.