Moran, Fundamentals of Engineering Thermodynamics, Chapter 13. 과잉공기와 압력을 바꾸고 블록을 옮기면서 연소의 에너지 수지를 확인한다.Moran, Fundamentals of Engineering Thermodynamics, Chapter 13. Drag the excess air, change the pressure, and move blocks to check the energy balance of combustion.
이론 공기와 과잉공기이슬점생성 엔탈피발열량 HHV와 LHV단열화염온도화학 엑서지
Section 13.1
연소 소개: 이론 공기, 과잉공기, 이슬점Introducing Combustion: Theoretical Air, Excess Air, Dew Point
연소는 연료의 가연 원소인 탄소, 수소, 황이 빠르게 산화되면서 에너지를 방출하는 반응이다. 탄소가 모두 CO2로, 수소가 모두 H2O로 산화되면 완전연소(complete combustion)라 하고, 그렇지 않으면 불완전연소이다. 화학 반응식의 양변에서 각 원소의 질량은 같아야 하지만 몰수는 같을 필요가 없다. 예를 들어 H2 1 kmol과 O2 0.5 kmol이 반응하면 H2O 1 kmol이 생겨 총 몰수가 줄어든다.Combustion is the rapid oxidation of the combustible elements of a fuel, carbon, hydrogen and sulfur, with energy release. Combustion is complete when all carbon becomes CO2 and all hydrogen becomes H2O; otherwise it is incomplete. The mass of each element must balance across the reaction equation, but the number of moles need not. For example, 1 kmol of H2 and 0.5 kmol of O2 give 1 kmol of H2O, so the total mole number decreases.
산화제는 대부분 공기이며, 공기는 O2 1 kmol당 N2 3.76 kmol인 이상기체 혼합물로 모형화한다. 이론 공기(theoretical air)는 완전연소에 필요한 최소 공기량이고, 이때 생성물에는 산소가 남지 않는다. 실제 연소기는 불완전연소를 막으려고 이론량보다 많은 공기를 넣으며, 그 초과분을 과잉공기(excess air)라 한다. 공기-연료비 AF는 공기 질량을 연료 질량으로 나눈 값이다. 과잉공기가 늘면 생성물에 O2와 N2가 더 많이 섞여 H2O의 몰분율이 낮아진다.The oxidizer is usually air, modeled as an ideal-gas mixture of 3.76 kmol N2 per kmol O2. Theoretical air is the minimum air for complete combustion, and the products then contain no free oxygen. Real burners supply more than the theoretical amount to avoid incomplete combustion, and the surplus is excess air. The air-fuel ratio AF is the mass of air divided by the mass of fuel. More excess air adds O2 and N2 to the products and lowers the mole fraction of H2O.
과잉공기 비율 $x$: 이론 공기에 대한 초과분의 비이다. 과잉공기 50%는 이론 공기의 150%이며 $x = 0.5$이다.Excess-air fraction $x$: the surplus relative to theoretical air. 50% excess air is 150% theoretical air, $x = 0.5$.
이슬점 온도(dew point): 생성물을 일정한 혼합물 압력에서 냉각할 때 수증기가 처음 응축하는 온도이다. 수증기 분압 $p_v = y_v p$에 해당하는 포화 온도로 구한다.Dew point temperature: the temperature at which water vapor first condenses when the products are cooled at constant mixture pressure. It is the saturation temperature at the vapor partial pressure $p_v = y_v p$.
응축수의 영향: 연료에 황이 있으면 응축수가 산성이 되어 배기관과 열교환기를 부식시키므로 배기 온도를 이슬점보다 높게 유지하는 경우가 많다.Effect of condensate: when the fuel contains sulfur, the condensate is acidic and corrodes stacks and heat exchangers, so exhaust is often kept above the dew point.
$$p_v=y_v\,p,\qquad T_{dp}=T_{\text{sat}}(p_v)$$
Figure 13.1과잉공기와 압력에 따른 배기 이슬점Exhaust Dew Point vs Excess Air and Pressure
과잉공기 $x$ (%)Excess air $x$ (%)20
배기 압력 $p$ (kPa)Exhaust pressure $p$ (kPa)101
CH4 이슬점CH4 dew point0
C3H8 이슬점C3H8 dew point0
C8H18 이슬점C8H18 dew point0
CH4 수증기 몰분율CH4 H2O mole fraction0
과잉공기가 늘수록 $y_v$가 작아져 이슬점이 낮아지고, 압력이 높아지면 $p_v$가 커져 이슬점이 올라간다. 수소 비율이 높은 CH4의 이슬점이 가장 높다. 포화 온도는 물의 Antoine 식(1-100 °C와 99-374 °C 두 구간 계수)으로 계산했고, 생성물은 이상기체 혼합물로 보았다.More excess air lowers $y_v$ and the dew point; higher pressure raises $p_v$ and the dew point. CH4, with the highest hydrogen share, has the highest dew point. Saturation temperature comes from the Antoine equation for water (two coefficient sets, 1-100 °C and 99-374 °C); products are treated as an ideal-gas mixture.
Figure 13.2배기 압력에 따른 수증기 응축 시작Onset of Water Condensation vs Exhaust Pressure
예측: CH4 배기가스의 압력을 올리면 이슬점은 어떻게 될까?Predict: what happens to the dew point of CH4 exhaust when the pressure is raised?
목표: 오른쪽 압력 막대의 핸들을 위아래로 끌어, 벽 온도 60 °C에서 응축이 막 시작되는 압력을 ±4 kPa 안으로 찾으세요. 과잉공기를 바꾸면 그 압력도 바뀝니다.Goal: drag the handle on the right pressure bar up and down to find, within 4 kPa, the pressure at which condensation just starts on a 60 °C wall. Changing the excess air moves that pressure.
압력 $p$ (kPa)Pressure $p$ (kPa)101
과잉공기 $x$ (%)Excess air $x$ (%)20
수증기 분압 $p_v$ (kPa)Vapor pressure $p_v$ (kPa)0
이슬점 (°C)Dew point (°C)0
60 °C 포화압 (kPa)p_sat at 60 °C (kPa)0
응축 여부Condensation—
$p_v$가 벽 온도의 포화압 $p_{sat}(T_w)$보다 커지면, 곧 $T_{dp} > T_w$이면 벽에 물방울이 맺힌다. 이슬점이 벽 온도와 같아지는 압력은 $p = p_{sat}(T_w)/y_v$이다.When $p_v$ exceeds the saturation pressure $p_{sat}(T_w)$ at the wall temperature, that is $T_{dp} > T_w$, droplets form on the wall. The pressure at which the dew point equals the wall temperature is $p = p_{sat}(T_w)/y_v$.
Section 13.2
반응계의 에너지 보존: 생성 엔탈피와 발열량Conservation of Energy for Reacting Systems: Enthalpy of Formation and Heating Values
반응이 일어나면 원자 결합이 바뀌므로 엔탈피의 기준을 모든 물질에 공통으로 정해야 한다. 표준 기준 상태($T_{ref} = 298.15$ K, $p_{ref} = 1$ atm)에서 안정한 원소의 엔탈피를 0으로 두고, 이 상태에서 원소로부터 화합물 1 kmol이 만들어질 때의 엔탈피 변화를 생성 엔탈피(enthalpy of formation) $\bar h_f^{\circ}$로 정의한다. 임의의 상태에서 엔탈피는 생성 엔탈피에 기준 상태로부터의 변화를 더해 얻는다.A reaction rearranges bonds, so enthalpy needs one common reference for all substances. At the standard state ($T_{ref} = 298.15$ K, $p_{ref} = 1$ atm) the enthalpy of every stable element is set to zero, and the enthalpy change when 1 kmol of a compound forms from its elements is the enthalpy of formation $\bar h_f^{\circ}$. The enthalpy at any state is the enthalpy of formation plus the change from the reference state.
정상 유동 반응기에서 연료 1 kmol당 에너지 수지는 생성물 엔탈피의 합에서 반응물 엔탈피의 합을 뺀 값이 $Q_{cv}-W_{cv}$와 같다는 식이다. 반응물과 생성물이 모두 $T_{ref}$, $p_{ref}$이면 이 차이가 연소 엔탈피(enthalpy of combustion) $\bar h_{RP}$이며, 발열 반응에서 음수이다. 연소 엔탈피의 크기를 연료 단위 질량당으로 나타낸 값이 발열량이다. 생성물의 물이 액체이면 고위 발열량(HHV), 수증기이면 저위 발열량(LHV)이고, 둘의 차이는 물의 증발 엔탈피에서 온다.For a steady-flow reactor, the energy balance per kmol of fuel says that the sum of product enthalpies minus the sum of reactant enthalpies equals $Q_{cv}-W_{cv}$. When reactants and products are both at $T_{ref}$, $p_{ref}$, this difference is the enthalpy of combustion $\bar h_{RP}$, negative for an exothermic reaction. Its magnitude per unit fuel mass is the heating value. It is the higher heating value (HHV) when the product water is liquid and the lower heating value (LHV) when it is vapor; the two differ by the enthalpy of vaporization of water.
생성 엔탈피 자료 (Moran 표 A-25, kJ/kmol, 298 K): CH4(g) -74,850, C3H8(g) -103,850, C8H18(l) -249,950, CO2 -393,520, H2O(g) -241,820, H2O(l) -285,830. N2와 O2는 0이다.Enthalpy-of-formation data (Moran Table A-25, kJ/kmol at 298 K): CH4(g) -74,850, C3H8(g) -103,850, C8H18(l) -249,950, CO2 -393,520, H2O(g) -241,820, H2O(l) -285,830. N2 and O2 are zero.
발열량 예: CH4의 HHV는 약 55,500 kJ/kg, LHV는 약 50,000 kJ/kg이다. 차이 약 5,500 kJ/kg은 $2 \times 44{,}010 / 16.04$와 같다.Heating-value example: CH4 has an HHV of about 55,500 kJ/kg and an LHV of about 50,000 kJ/kg. The gap of about 5,500 kJ/kg equals $2 \times 44{,}010 / 16.04$.
Figure 13.3생성물 블록으로 맞추는 반응 엔탈피Balancing Reaction Enthalpy with Product Blocks
예측: 생성물의 물이 수증기가 아니라 액체이면 연료 1 kmol이 방출하는 에너지는 어떻게 될까?Predict: if the product water is liquid instead of vapor, what happens to the energy released per kmol of fuel?
목표: 아래 블록을 위의 칸으로 끌어 C와 H의 원자 수를 맞추고, 물을 모두 액체로 만들어 HHV 상태를 완성하세요. 칸 안의 사각형을 밖으로 끌면 빠집니다.Goal: drag the blocks below into the box above, balance the C and H atoms, and make all the water liquid to reach the HHV state. Drag a square out of the box to remove it.
$\bar h_{RP}$ (kJ/kmol)$\bar h_{RP}$ (kJ/kmol)—
발열량 (kJ/kg)Heating value (kJ/kg)—
상태State—
물이 증기에서 액체로 바뀌면 생성 엔탈피가 -241,820에서 -285,830 kJ/kmol로 낮아져 생성물 엔탈피 합이 더 작아지므로 방출 에너지가 커진다. 증가분은 H2O 1 kmol당 44,010 kJ이다. O2 계수는 산소 원자 수에서 자동으로 정해진다.When water goes from vapor to liquid its enthalpy of formation drops from -241,820 to -285,830 kJ/kmol, so the product enthalpy sum falls and the released energy grows by 44,010 kJ per kmol of H2O. The O2 coefficient is set automatically by the oxygen atom count.
Section 13.3
단열화염온도 구하기Determining the Adiabatic Flame Temperature
외부로 열과 일을 주고받지 않는 정상 유동 반응기에서 완전연소한 생성물이 도달하는 온도를 단열화염온도(adiabatic flame temperature)라 한다. 에너지 수지에서 $Q_{cv} = W_{cv} = 0$이므로 반응물의 엔탈피 합이 생성물의 엔탈피 합과 같고, 이 식을 만족하는 생성물 온도를 반복 계산으로 찾는다. 엔탈피 변화 $\Delta \bar h$는 $\bar c_p(T)$ 다항식을 298 K부터 $T$까지 적분해 얻는다.The temperature reached by the products of complete combustion in a steady-flow reactor with no heat or work exchange is the adiabatic flame temperature. The energy balance with $Q_{cv} = W_{cv} = 0$ equates the reactant and product enthalpy sums, and the product temperature that satisfies it is found by iteration. The enthalpy change $\Delta \bar h$ comes from integrating a $\bar c_p(T)$ polynomial from 298 K to $T$.
과잉공기가 늘면 같은 반응열을 더 많은 N2와 O2가 나누어 가지므로 화염온도가 낮아지고, 이론 공기에서 최대가 된다. 반대로 공기를 예열하면 반응물 엔탈피가 커져 화염온도가 올라간다. 실제 화염은 이 값보다 낮다. 계산은 해리(dissociation)를 무시했고, 실제로는 열손실과 불완전연소도 있기 때문이다. 가스터빈 연소기는 터빈 날개가 견디도록 과잉공기를 크게 두어 온도를 낮춘다.More excess air spreads the same heat of reaction over more N2 and O2, lowering the flame temperature, which peaks at theoretical air. Preheating the air raises the reactant enthalpy and the flame temperature. Real flames are cooler than this value because the calculation ignores dissociation, and real burners also lose heat and burn incompletely. Gas-turbine combustors use large excess air to keep the gas temperature within blade limits.
풀이 순서: 반응식을 쓰고 몰수를 정한다. 반응물 엔탈피 합을 계산한다. 생성물 온도를 가정해 생성물 엔탈피 합을 구하고 두 값이 같아질 때까지 온도를 고친다.Procedure: write the reaction and fix the mole numbers, compute the reactant enthalpy sum, assume a product temperature, compute the product enthalpy sum, and adjust the temperature until the two are equal.
해리: 약 2000 K 이상에서 CO2와 H2O가 CO, H2, OH 등으로 일부 분해되며 열을 흡수한다. 이를 고려하면 화염온도가 100 K 이상 낮아질 수 있다.Dissociation: above about 2000 K, CO2 and H2O partly break into CO, H2, OH and others, absorbing heat. Including it can lower the flame temperature by 100 K or more.
Figure 13.4과잉공기에 따른 생성물 조성과 화염온도Product Composition and Flame Temperature vs Excess Air
예측: 이론 공기에서 과잉공기를 늘리면 단열화염온도는 어떻게 될까?Predict: starting from theoretical air, what happens to the adiabatic flame temperature as excess air increases?
목표: 버너 아래의 눈금에서 핸들을 좌우로 끌어 과잉공기를 바꾸고, 단열화염온도를 1800 K ±30 K에 맞추세요. 연료를 바꿔 다시 시도할 수 있습니다.Goal: drag the knob on the scale below the burner to change the excess air, and bring the adiabatic flame temperature to 1800 K ±30 K. Switch the fuel to try again.
과잉공기 $x$ (%)Excess air $x$ (%)0%
과잉공기Excess air0%
공기-연료비 AF (kg/kg)AF (kg/kg)0
단열화염온도 (K)Adiabatic flame T (K)0
H2O 몰분율H2O mole fraction0
과잉공기를 늘릴수록 O2와 N2의 몰분율이 커지고 같은 반응열이 더 많은 기체에 분배되어 온도가 내려간다. 화염 높이는 과잉공기에 비례해 늘리고 색은 온도에 맞춰 바꾼 것으로, 실제 화염 길이를 계산한 값은 아니다.More excess air raises the O2 and N2 mole fractions, and the same heat of reaction is shared by more gas, so the temperature falls. Flame height grows with excess air and the color follows temperature; neither is a computed flame length.
Figure 13.5연료별 단열화염온도와 공기 예열Adiabatic Flame Temperature by Fuel and Air Preheat
과잉공기 $x$ (%)Excess air $x$ (%)50
공기 입구 온도 (K)Air inlet temperature (K)298
CH4 (K)CH4 (K)0
C3H8 (K)C3H8 (K)0
C8H18 (K)C8H18 (K)0
CH4 이론 공기 화염온도 (K)CH4 theoretical air (K)0
CO2, H2O, N2, O2의 엔탈피는 NASA 7계수 $c_p$ 다항식(GRI-Mech 3.0 열역학 자료, 1000 K 기준 두 구간)을 적분해 계산하고 생성 엔탈피는 Moran 표 A-25 값을 썼다. 연료는 298 K로 들어간다고 보아 $\bar h_f^{\circ}$만 사용했다. 해리는 무시했으므로 실제 화염온도보다 높다. 이론 공기의 CH4는 약 2330 K이다.Enthalpies of CO2, H2O, N2 and O2 come from integrating NASA 7-coefficient $c_p$ polynomials (GRI-Mech 3.0 thermo data, two ranges split at 1000 K); formation enthalpies are Moran Table A-25. Fuel enters at 298 K, so only $\bar h_f^{\circ}$ is used. Dissociation is ignored, so the values exceed real flame temperatures. CH4 with theoretical air gives about 2330 K.
Section 13.5
절대 엔트로피와 열역학 제3법칙Absolute Entropy and the Third Law
반응계의 엔트로피 수지에는 기준 상태가 필요하다. 제3법칙에 따라 0 K의 순수한 완전 결정 물질의 엔트로피를 0으로 두면, 모든 물질의 절대 엔트로피(absolute entropy)를 정할 수 있다. 표에는 1 atm에서의 값 $\bar s^{\circ}(T)$가 실려 있다. 이상기체 혼합물의 성분 $i$는 혼합물 안의 분압 $y_i p$를 써서 압력 보정을 해야 한다.The entropy balance for a reacting system needs a reference state. By the third law, setting the entropy of a pure perfect crystal at 0 K to zero fixes the absolute entropy of every substance. Tables list the value at 1 atm, $\bar s^{\circ}(T)$. Component $i$ of an ideal-gas mixture needs a pressure correction using its partial pressure $y_i p$.
정상 유동 반응기의 엔트로피 생성률은 생성물과 반응물의 절대 엔트로피 차이에서 열전달에 의한 항을 뺀 값이다. 같은 연소라도 반응물과 생성물의 온도 차이가 클수록, 즉 연소가 비가역적일수록 $\sigma_{cv}$가 커진다. Gibbs 함수 $\bar g = \bar h - T\bar s$의 생성값 $\bar g_f^{\circ}$는 298 K, 1 atm에서 원소로부터 화합물이 만들어질 때의 Gibbs 함수 변화이며, 화학 평형과 화학 엑서지를 계산할 때 쓴다.The entropy generation rate of a steady-flow reactor is the difference of absolute entropies of products and reactants minus the heat-transfer term. For the same fuel, the larger the temperature change between reactants and products, that is, the more irreversible the combustion, the larger $\sigma_{cv}$. The Gibbs function of formation $\bar g_f^{\circ}$ is the change of $\bar g = \bar h - T\bar s$ when a compound forms from its elements at 298 K and 1 atm, and it is used for chemical equilibrium and chemical exergy.
제3법칙: 0 K에서 완전 결정의 엔트로피는 0이다. 이 기준 덕분에 $\bar s^{\circ}$ 값이 물질마다 하나씩 표에 있다.Third law: the entropy of a perfect crystal at 0 K is zero. With this reference each substance has a single tabulated $\bar s^{\circ}$ value.
Gibbs 함수 생성값 (kJ/kmol, 298 K): CH4 -50,790, C3H8(g) -23,490, C8H18(l) +6,610, CO2 -394,360, H2O(l) -237,180. 원소의 값은 0이다.Gibbs function of formation (kJ/kmol at 298 K): CH4 -50,790, C3H8(g) -23,490, C8H18(l) +6,610, CO2 -394,360, H2O(l) -237,180. Elements are zero.
Section 13.6
화학 엑서지의 개념Conceptualizing Chemical Exergy
물질의 엑서지는 열적 상태와 압력으로 정해지는 부분 외에, 주위 환경과 화학 조성이 다르기 때문에 생기는 부분인 화학 엑서지(chemical exergy)를 포함한다. 연료는 주위 공기에 없는 물질이므로 화학 엑서지가 매우 크다. 이를 정의하려면 환경 모형이 필요하며, 대기 조성과 $T_0 = 298.15$ K, $p_0 = 1$ atm을 기준으로 한다.The exergy of matter includes, beyond the part set by thermal state and pressure, a chemical exergy that arises because its composition differs from the environment. A fuel is not present in ambient air, so its chemical exergy is large. Defining it needs an environment model, here the atmospheric composition at $T_0 = 298.15$ K and $p_0 = 1$ atm.
연료의 화학 엑서지는 연료가 환경에서 가져온 O2와 가역적으로 반응해 환경과 평형인 CO2와 H2O가 될 때 얻을 수 있는 최대 일이다. 이 일은 반응의 Gibbs 함수 변화에 환경 성분의 몰분율 $y^e$로 정해지는 보정항을 더한 값이다. 보정항은 연료가 대기 중 O2를 쓰고 CO2와 H2O를 대기 농도로 내보내는 데서 생긴다.The chemical exergy of a fuel is the maximum work obtainable when it reacts reversibly with O2 taken from the environment and the products CO2 and H2O leave in equilibrium with the environment. This work equals the Gibbs-function change of the reaction plus a correction set by the environmental mole fractions $y^e$. The correction arises because the fuel consumes atmospheric O2 and releases CO2 and H2O at their atmospheric concentrations.
$$\bar e^{ch}=\left[\bar g_F+\left(a+\tfrac b4\right)\bar g_{\mathrm{O_2}}-a\,\bar g_{\mathrm{CO_2}}-\tfrac b2\,\bar g_{\mathrm{H_2O}}\right]_{T_0,p_0}+\bar R T_0\ln\frac{\left(y^e_{\mathrm{O_2}}\right)^{a+b/4}}{\left(y^e_{\mathrm{CO_2}}\right)^{a}\left(y^e_{\mathrm{H_2O}}\right)^{b/2}}$$
환경 모형: Moran의 표준 환경(Model II)은 건조 공기에 가까운 조성에 포화 수증기 분압을 더한 대기로, 그 안에서 CO2, H2O, O2가 기준 성분이다.Environment model: Moran's standard environment (Model II) is an atmosphere of near-dry-air composition plus saturated water vapor, with CO2, H2O and O2 as the reference components.
총 엑서지: 흐르는 물질의 총 엑서지는 열적 상태와 압력에 따른 엑서지에 화학 엑서지를 더한 값이다. 연소기의 엑서지 효율을 계산할 때 연료의 화학 엑서지를 입력으로 쓴다.Total exergy: the total exergy of a flowing substance is its thermomechanical exergy plus its chemical exergy. The fuel's chemical exergy is the input when computing combustor exergetic efficiency.
Section 13.7
표준 화학 엑서지Standard Chemical Exergy
표준 화학 엑서지(standard chemical exergy)는 환경 모형을 하나 고정하고 물질마다 미리 계산해 표에 모아 둔 값이다. 탄화수소 CaHb는 Gibbs 함수 생성값과 기준 성분 CO2, H2O(l), O2의 표준 화학 엑서지로 계산할 수 있다. 이 값은 Moran 표 A-26(Model II)에 있다.The standard chemical exergy is computed in advance for each substance with one fixed environment model and collected in a table. For a hydrocarbon CaHb it follows from the Gibbs function of formation and the standard chemical exergies of the reference components CO2, H2O(l) and O2. The values are in Moran Table A-26 (Model II).
CH4를 예로 들면 $-50{,}790 + 394{,}360 + 2 \times 237{,}180 = 817{,}930$ kJ/kmol에 $19{,}870 + 2 \times 900 - 2 \times 3{,}970 = 13{,}730$ kJ/kmol을 더해 831,660 kJ/kmol이 되고, 이는 표의 831,650과 같다. 탄화수소의 표준 화학 엑서지는 고위 발열량과 5% 안팎으로 가깝다. 반응에서 엔트로피 변화 $T_0\Delta \bar s$가 연료 엔탈피에 비해 작기 때문이다. 연료를 단열 연소시켜 열로 쓰면 이 엑서지 가운데 일부가 엔트로피 생성으로 파괴된다.For CH4, $-50{,}790 + 394{,}360 + 2 \times 237{,}180 = 817{,}930$ kJ/kmol plus $19{,}870 + 2 \times 900 - 2 \times 3{,}970 = 13{,}730$ kJ/kmol gives 831,660 kJ/kmol, matching the tabulated 831,650. The standard chemical exergy of a hydrocarbon is within a few percent of its higher heating value, because the entropy term $T_0\Delta \bar s$ of the reaction is small against the fuel enthalpy. When the fuel is burned adiabatically and used as heat, part of this exergy is destroyed by entropy generation.
표준 화학 엑서지 자료 (Moran 표 A-26, Model II, kJ/kmol): CH4 831,650, C3H8(g) 2,150,160, C8H18(l) 5,413,100. 기준 성분은 CO2 19,870, H2O(l) 900, O2 3,970이다.Standard chemical exergy data (Moran Table A-26, Model II, kJ/kmol): CH4 831,650, C3H8(g) 2,150,160, C8H18(l) 5,413,100. Reference components: CO2 19,870, H2O(l) 900, O2 3,970.
Figure 13.6연료 질량당 고위 발열량과 화학 엑서지HHV and Chemical Exergy per Unit Fuel Mass
예측: 화학 엑서지 유입률 100 MW를 만들 때 연료 질량유량이 가장 적게 드는 연료는 무엇일까?Predict: which fuel needs the smallest mass flow rate to supply 100 MW of chemical exergy?
목표: 연료 줄을 눌러 고른 뒤 아래 눈금의 핸들을 끌어 질량유량을 조절하고, 세 연료 모두에서 화학 엑서지 유입률을 100 MW ±3 MW에 맞추세요.Goal: click a fuel row to select it, drag the knob on the scale below to set the mass flow rate, and bring the chemical exergy input to 100 MW ±3 MW for all three fuels.
선택한 연료Selected fuelCH4
질량유량 (kg/s)Mass flow (kg/s)0
화학 엑서지 유입 (MW)Chemical exergy input (MW)0
엑서지 대 HHV 비Exergy / HHV0
질량당 화학 엑서지는 CH4 51.8 MJ/kg, C3H8 48.8 MJ/kg, C8H18 47.4 MJ/kg이며, 수소 비율이 높을수록 크다. 엑서지 대 HHV 비는 0.93부터 0.99로 모두 1에 가깝다. 질량당 값은 표 A-26의 kmol당 값을 몰질량으로 나눈 것이고, HHV는 표 A-25의 생성 엔탈피에서 계산했다.Chemical exergy per kg is 51.8 MJ/kg for CH4, 48.8 for C3H8 and 47.4 for C8H18, larger for a higher hydrogen share. The exergy-to-HHV ratio is 0.93 to 0.99, all near 1. Per-mass values divide the per-kmol Table A-26 data by molar mass, and HHV is computed from Table A-25 formation enthalpies.
Self-Check
확인 문제Quiz
Q1. CH4를 이론 공기의 120%(과잉공기 20%)로 완전연소할 때 생성물 중 H2O의 몰분율은?Q1. CH4 burns completely with 120% of theoretical air (20% excess air). What is the H2O mole fraction in the products?
생성물은 CO2 1, H2O 2, O2 0.4, N2 $3.76 \times 2 \times 1.2 = 9.024$ kmol로 합계 12.424 kmol이다. $y_{H_2O} = 2/12.424 = 0.161$이다. 19.0%는 이론 공기(과잉공기 0%)의 값이다.The products are 1 CO2, 2 H2O, 0.4 O2 and $3.76 \times 2 \times 1.2 = 9.024$ N2, total 12.424 kmol, so $y_{H_2O} = 2/12.424 = 0.161$. The 19.0% value belongs to theoretical air (0% excess).
Q2. 같은 연료에서 고위 발열량(HHV)이 저위 발열량(LHV)보다 큰 이유는?Q2. Why is the higher heating value (HHV) of a fuel larger than its lower heating value (LHV)?
두 값은 같은 반응에서 생성물의 물 상태만 다르다. CH4는 물 2 kmol이 생겨 $2 \times 44{,}010 = 88{,}020$ kJ/kmol, 질량당으로 약 5,490 kJ/kg 차이가 난다.The two values describe the same reaction and differ only in the state of the product water. CH4 forms 2 kmol of water, a difference of $2 \times 44{,}010 = 88{,}020$ kJ/kmol, about 5,490 kJ/kg.
Q3. 표의 CH4 표준 화학 엑서지 831,650 kJ/kmol과 HHV 890,330 kJ/kmol을 비교하면 엑서지 대 HHV 비는 얼마인가?Q3. Comparing the tabulated CH4 standard chemical exergy of 831,650 kJ/kmol with its HHV of 890,330 kJ/kmol, what is the exergy-to-HHV ratio?
$831{,}650 / 890{,}330 = 0.934$이다. 탄화수소의 화학 엑서지는 HHV와 비슷하지만, 반응의 엔트로피 변화에 해당하는 $T_0 \Delta \bar s$ 항 때문에 정확히 같지는 않다. 수소 비율이 높은 CH4는 비가 비교적 낮고 C8H18은 0.99에 가깝다.$831{,}650 / 890{,}330 = 0.934$. The chemical exergy of a hydrocarbon is close to its HHV but not equal, because of the $T_0 \Delta \bar s$ term of the reaction. CH4, with a high hydrogen share, has a lower ratio and C8H18 is near 0.99.
What If?
만약에?What If?
만약 연소 공기를 800 K까지 예열하면 CH4의 이론 공기 화염온도는?What if the combustion air is preheated to 800 K? What is the CH4 flame temperature with theoretical air?
클릭하여 확인 →Click to reveal →
298 K 공기일 때 약 2330 K이던 값이 약 2650 K으로 올라간다. 예열 공기가 가져오는 엔탈피만큼 생성물이 더 높은 온도에 도달하기 때문이다. 다만 이 온도에서는 해리가 크게 일어나 실제 값은 훨씬 낮고, 질소 산화물 생성도 급격히 늘어난다.The value rises from about 2330 K with 298 K air to about 2650 K, because the preheated air brings extra enthalpy that the products must carry. At this temperature dissociation is large, so the real value is much lower, and nitrogen oxide formation rises sharply.
만약 공기 대신 순수 O2로 연소하면?What if the fuel burns in pure O2 instead of air?
클릭하여 확인 →Click to reveal →
생성물에 N2가 없어 같은 반응열이 CO2와 H2O 두 성분에만 분배되므로, 해리를 무시한 계산으로는 3500 K를 훨씬 넘는다. 실제로는 해리가 온도를 3000 K 근처로 제한한다. 이 높은 온도는 용접과 용해로에 쓰이지만 재료가 견뎌야 한다.With no N2 in the products, the same heat of reaction goes to CO2 and H2O only, so the dissociation-free calculation gives far above 3500 K. In practice dissociation holds the temperature near 3000 K. Such temperatures serve welding and melting furnaces, but materials must withstand them.
만약 배기가스를 이슬점 아래까지 식혀 응축열을 회수하면?What if the exhaust is cooled below the dew point to recover the condensation heat?
클릭하여 확인 →Click to reveal →
LHV 기준으로 효율을 계산하는 보일러에서는 응축으로 HHV와 LHV의 차이만큼 열을 더 얻으므로 CH4에서 최대 약 11%의 열이 추가된다. 응축형 보일러가 이 방식이다. 응축수는 산성이므로 열교환기를 내식 재료로 만들어야 한다.In a boiler rated on LHV, condensation recovers the gap between HHV and LHV, up to about 11% extra heat for CH4. Condensing boilers work this way. The condensate is acidic, so the heat exchanger needs corrosion-resistant material.
Key Takeaways
01
공기 비율이 생성물을 정한다Air Ratio Sets the Products
원소별 원자 수 균형으로 생성물 몰수가 정해지며, 과잉공기는 O2와 N2를 늘려 H2O 몰분율과 이슬점을 낮춘다.Atom balance fixes the product moles; excess air adds O2 and N2 and lowers the H2O mole fraction and dew point.
02
생성 엔탈피가 공통 기준이다Formation Enthalpy Is the Common Reference
$\bar h_f^{\circ}$로 반응물과 생성물의 엔탈피를 같은 기준에서 합산하고, 물이 액체인지 증기인지에 따라 HHV와 LHV가 갈린다.$\bar h_f^{\circ}$ puts reactant and product enthalpies on one scale, and the state of water separates HHV from LHV.
03
단열화염온도의 조건What Sets Adiabatic Flame Temperature
이론 공기에서 최대이고 과잉공기가 늘수록 낮아지며, 공기 예열은 온도를 올린다. 해리를 무시한 값이므로 실제보다 높다.It peaks at theoretical air, falls with excess air and rises with air preheat. Ignoring dissociation, it overestimates real flames.
04
연료의 화학 엑서지Chemical Exergy of Fuel
표준 화학 엑서지는 Gibbs 함수 변화와 환경 보정으로 정해지며 탄화수소에서는 HHV의 93%부터 99%이다.Standard chemical exergy follows from the Gibbs-function change and an environment correction, and for hydrocarbons is 93% to 99% of HHV.