이상기체 혼합물과 습공기 응용Ideal Gas Mixtures and Psychrometric Applications
Moran, Fundamentals of Engineering Thermodynamics, Chapter 12. 슬라이더를 움직이면 그래프가 실시간으로 반응합니다.Moran, Fundamentals of Engineering Thermodynamics, Chapter 12. Move the sliders to see the graphs respond in real time.
혼합물의 조성은 질량 기준의 질량분율 $mf_i$ 또는 몰 수 기준의 몰분율 $y_i$로 나타낸다. 성분 $i$의 몰 수는 질량을 분자량으로 나눈 $n_i = m_i/M_i$이고 혼합물의 몰 수는 $n = \sum n_i$이므로, 두 분율은 각각 합이 1이다.Mixture composition is given either on a mass basis by the mass fraction $mf_i$ or on a mole basis by the mole fraction $y_i$. The moles of component $i$ are $n_i = m_i/M_i$ and the mixture has $n = \sum n_i$, so each set of fractions sums to one.
혼합물을 하나의 순수 기체처럼 다루려면 겉보기 분자량(apparent molecular weight) $M = \sum y_i M_i$를 쓴다. 건조 공기는 질소 약 78 %, 산소 약 21 %, 아르곤 약 1 %의 몰분율을 가지며 $M = 28.97$ kg/kmol이다. 분석 결과가 몰분율로 주어지든 질량분율로 주어지든 아래 환산식으로 서로 바꿀 수 있다.To treat a mixture as one pure gas, use the apparent molecular weight $M = \sum y_i M_i$. Dry air is about 78 % nitrogen, 21 % oxygen and 1 % argon by mole and has $M = 28.97$ kg/kmol. Whether an analysis is given by mole or by mass, the conversion below switches between the two.
몰분율 $y_i$: 성분 $i$의 몰 수를 혼합물의 몰 수로 나눈 값이다. 이상기체에서는 부피 분율과 같고, 연소 생성물의 몰 분석(dry basis)도 이 형태이다.Mole fraction $y_i$: moles of component $i$ divided by the moles of the mixture. For ideal gases it equals the volume fraction, and the molar analysis of combustion products is given in this form.
질량분율 $mf_i$: 성분 $i$의 질량을 혼합물의 질량으로 나눈 값이다. 무거운 성분은 몰분율보다 질량분율이 크다.Mass fraction $mf_i$: mass of component $i$ divided by the mass of the mixture. A heavy component has a mass fraction larger than its mole fraction.
겉보기 분자량 $M$: 몰분율로 가중 평균한 분자량이다. 질량분율로 주어진 경우에는 $1/M = \sum mf_i/M_i$를 쓴다.Apparent molecular weight $M$: the mole-fraction weighted mean of the molecular weights. When mass fractions are given, use $1/M = \sum mf_i/M_i$.
Section 12.2
p, V, T 관계: Dalton 모델과 Amagat 모델Relating p, V and T: Dalton and Amagat Models
Dalton 모델에서는 각 성분이 혼합물과 같은 온도 $T$와 부피 $V$를 단독으로 차지할 때의 압력을 분압 $p_i$로 정의한다. 이상기체이면 $p_i = n_i \bar{R} T/V$이므로 $p_i = y_i p$이고, 분압의 합이 전체 압력이다.In the Dalton model each component is taken to occupy the whole volume $V$ alone at the mixture temperature $T$, and the pressure it would then exert is its partial pressure $p_i$. For ideal gases $p_i = n_i \bar{R} T/V$, so $p_i = y_i p$ and the partial pressures add up to the total pressure.
Amagat 모델은 각 성분이 혼합물과 같은 $T$와 $p$에서 단독으로 차지하는 부피를 분체적 $V_i$로 정의한다. 이상기체에서는 $V_i = y_i V$이다. 두 모델은 이상기체에서 같은 결과를 주고, 실제 기체 혼합물에서는 서로 다른 값을 준다. 이 장에서는 모든 혼합물을 이상기체로 가정하므로 몰분율 하나로 분압과 분체적이 모두 정해진다.The Amagat model defines the partial volume $V_i$ as the volume a component would occupy alone at the mixture $T$ and $p$. For ideal gases $V_i = y_i V$. The two models agree for ideal gases and differ for real mixtures. This chapter treats every mixture as an ideal gas, so the mole fraction alone fixes both the partial pressure and the partial volume.
$$p_i = y_i\, p, \qquad p = \sum_i p_i, \qquad V_i = y_i\, V, \qquad V = \sum_i V_i$$
분압: 성분이 혼합물의 온도와 부피를 혼자 차지할 때의 압력이다. 물의 증기압, 산소 분압처럼 상평형과 반응 해석에 직접 쓰인다.Partial pressure: the pressure a component would exert alone at the mixture temperature and volume. It is used directly in phase equilibrium and reaction analysis, as in water vapor pressure or oxygen partial pressure.
분체적: 성분이 혼합물의 온도와 압력에서 혼자 차지하는 부피이다. 이상기체에서는 분체적 분율이 몰분율과 같다.Partial volume: the volume a component would occupy alone at the mixture temperature and pressure. For ideal gases the partial-volume fraction equals the mole fraction.
Figure 12.1이원 혼합물의 몰분율, 질량분율, 겉보기 분자량Mole Fraction, Mass Fraction and Apparent Molecular Weight of a Binary Mixture
N2에 성분 B를 섞는다. 아래 버튼으로 B를 고르고, 슬라이더로 B의 몰분율 $y_B$를 바꾸세요.Mix component B into N2. Pick B with the buttons and change its mole fraction $y_B$ with the slider.
몰분율 $y_B$Mole fraction $y_B$0.25
전체 압력 $p$ (bar)Total pressure $p$ (bar)2.0
겉보기 M (kg/kmol)Apparent M (kg/kmol)0
B의 질량분율Mass fraction of B0
B의 분압 (bar)Partial pressure of B (bar)0
B의 분체적 / VPartial volume of B / V0
분자량 데이터는 Moran 부록 Table A-1을 쓴다. B가 N2보다 무거우면 질량분율 곡선이 대각선보다 위에 있고, 가벼우면 아래에 있다. 분압과 분체적 분율은 이상기체이므로 몰분율과 같다.Molecular weights are from Moran Table A-1. If B is heavier than N2 the mass-fraction curve lies above the diagonal, and if lighter, below it. Partial pressure and partial-volume fractions equal the mole fraction because the gases are ideal.
Section 12.3 and 12.4
혼합물의 U, H, S와 혼합 과정 해석Mixture U, H, S and Analysis of Mixing Processes
이상기체 혼합물의 내부에너지와 엔탈피는 각 성분이 혼합물의 온도에서 갖는 값의 합이다. 이상기체의 $u$와 $h$는 온도만의 함수이므로 혼합해도 서로 영향을 주지 않는다. 비열도 같은 방식으로 $\bar{c}_p = \sum y_i \bar{c}_{p,i}$로 더한다.The internal energy and enthalpy of an ideal gas mixture are the sums of the values each component has at the mixture temperature. Ideal-gas $u$ and $h$ depend only on temperature, so the components do not affect each other. Specific heats add in the same way, $\bar{c}_p = \sum y_i \bar{c}_{p,i}$.
엔트로피는 다르다. 각 성분의 엔트로피는 혼합물의 온도와 그 성분의 분압 $p_i = y_i p$에서 계산해야 한다. 분압은 전체 압력보다 낮으므로 각 성분의 엔트로피가 $-\bar{R}\ln y_i$만큼 커지고, 같은 $T$와 $p$의 순수 기체를 섞기만 해도 엔트로피가 증가한다. 이 증가량이 혼합 엔트로피이다.Entropy is different. Each component entropy must be evaluated at the mixture temperature and the component partial pressure $p_i = y_i p$. Since the partial pressure is below the total pressure, each component gains $-\bar{R}\ln y_i$, and simply mixing pure gases at the same $T$ and $p$ raises the entropy. This is the entropy of mixing.
단열된 용기에서 칸막이로 나뉜 두 기체를 섞는 문제는 에너지 수지로 푼다. 일과 열이 없으므로 $U$가 일정하고, 비열이 일정하면 최종 온도가 $T_f = \sum n_i \bar{c}_{v,i} T_i / \sum n_i \bar{c}_{v,i}$이다. 처음 온도와 압력이 같은 기체끼리는 온도가 변하지 않고 엔트로피 생성만 $\Delta S = -n\bar{R}\sum y_i \ln y_i$로 남는다.Mixing two gases separated by a partition in an insulated vessel is solved with an energy balance. With no work or heat, $U$ is constant and for constant specific heats the final temperature is $T_f = \sum n_i \bar{c}_{v,i} T_i / \sum n_i \bar{c}_{v,i}$. For gases starting at the same temperature and pressure the temperature does not change and only the entropy production remains, $\Delta S = -n\bar{R}\sum y_i \ln y_i$.
혼합 엔트로피: 같은 $T$와 $p$의 서로 다른 순수 기체를 섞을 때의 엔트로피 증가이다. 이원 혼합물에서 $y = 0.5$일 때 최대이며 $\bar{R}\ln 2 = 5.76$ kJ/(kmol K)이다.Entropy of mixing: the entropy increase when different pure gases at the same $T$ and $p$ are mixed. For a binary mixture it is largest at $y = 0.5$ and equals $\bar{R}\ln 2 = 5.76$ kJ/(kmol K).
같은 기체끼리 섞는 경우: 칸막이 양쪽이 같은 종류의 기체이고 $T$와 $p$가 같으면 거시적 상태가 변하지 않으므로 $\Delta S = 0$이다. 혼합 엔트로피 식은 서로 구별되는 기체에만 적용한다.Mixing identical gases: if both sides hold the same gas at the same $T$ and $p$, the macroscopic state does not change, so $\Delta S = 0$. The mixing formula applies only to distinguishable gases.
Figure 12.2칸막이를 제거할 때의 혼합 엔트로피Entropy of Mixing When the Partition Is Removed
예측: 같은 $T$와 $p$의 기체 A와 B를 칸막이로 나눠 두었다. 칸막이를 제거하면 계 전체의 엔트로피 변화는 어떻게 될까?Predict: gases A and B at the same $T$ and $p$ sit on either side of a partition. What is the entropy change of the whole system when the partition is removed?
목표: 칸막이를 좌우로 끌어 A의 몰분율을 정하고, 칸막이를 위로 끌어 올려 제거하세요. 혼합 엔트로피가 5.7 kJ/(kmol K) 이상이 되도록 하세요.Goal: drag the partition left or right to set the mole fraction of A, then drag it upward to remove it. Make the entropy of mixing at least 5.7 kJ/(kmol K).
A의 몰분율 $y_A$Mole fraction $y_A$0.20
혼합 엔트로피 (kJ/(kmol K))Entropy of mixing (kJ/(kmol K))0
A 입자의 오른쪽 비율Share of A on the right0 %
$\Delta \bar{s} = -\bar{R}(y\ln y + (1-y)\ln(1-y))$를 쓴다. $y = 0.5$에서 최대 5.76이고 어느 조성에서도 이 값을 넘지 못한다. 한 번 섞인 입자가 저절로 원래 칸으로 돌아갈 확률은 입자 수가 많을수록 사실상 0이므로 이 과정은 비가역이다.The formula is $\Delta \bar{s} = -\bar{R}(y\ln y + (1-y)\ln(1-y))$. The maximum is 5.76 at $y = 0.5$ and no composition exceeds it. The chance that mixed particles sort themselves back is essentially zero for many particles, so the process is irreversible.
Section 12.5 and 12.6
습공기의 원리와 습구 온도Psychrometric Principles and Wet-Bulb Temperature
습공기(moist air)는 건조 공기와 수증기의 이상기체 혼합물이다. 대기압 근처에서 수증기 분압 $p_v$는 같은 온도의 포화압력 $p_g$보다 클 수 없다. 건조 공기 질량에 대한 수증기 질량의 비를 습도비(humidity ratio) $\omega$, 실제 $p_v$와 포화압력 $p_g$의 비를 상대습도 $\phi$라고 한다.Moist air is an ideal gas mixture of dry air and water vapor. Near atmospheric pressure the vapor partial pressure $p_v$ cannot exceed the saturation pressure $p_g$ at the same temperature. The ratio of vapor mass to dry-air mass is the humidity ratio $\omega$, and the ratio of the actual $p_v$ to $p_g$ is the relative humidity $\phi$.
수증기 압력은 증기표 대신 Magnus 식 $p_g = 0.61094\exp[17.625\,T/(T+243.04)]$ kPa ($T$는 $^{\circ}\mathrm{C}$)으로 계산한다. 이 식은 0부터 50 $^{\circ}\mathrm{C}$에서 증기표와 0.5 % 안쪽으로 일치한다. 같은 $\omega$를 유지하며 공기를 냉각할 때 $\phi$가 100 %에 도달하는 온도가 노점(dew point) $T_d$이며, $p_v = p_g(T_d)$로 구한다.Instead of steam tables, vapor pressure is computed here with the Magnus equation $p_g = 0.61094\exp[17.625\,T/(T+243.04)]$ kPa ($T$ in $^{\circ}\mathrm{C}$). It agrees with the steam table to within 0.5 % from 0 to 50 $^{\circ}\mathrm{C}$. The temperature at which $\phi$ reaches 100 % while cooling at constant $\omega$ is the dew point $T_d$, found from $p_v = p_g(T_d)$.
습공기의 엔탈피는 건조 공기 1 kg을 기준으로 적는다. 습구 온도(wet-bulb temperature) $T_{wb}$는 젖은 심지를 감싼 온도계가 가리키는 온도이고, 단열 포화 과정의 에너지 수지에서 구한다. 이 그림에서는 아래 경험식을 쓰며, 건구 온도 $T$와 $\omega$를 알면 $T_{wb}$가 정해진다.Moist-air enthalpy is written per kg of dry air. The wet-bulb temperature $T_{wb}$ is what a thermometer wrapped in a wet wick reads and follows from the energy balance of adiabatic saturation. The figures here use the empirical relation below, so $T$ and $\omega$ fix $T_{wb}$.
습도비 $\omega$: 건조 공기 1 kg에 들어 있는 수증기의 kg 수이다. $\omega = 0.622\,p_v/(p-p_v)$에서 0.622는 물과 공기의 분자량 비 18.02/28.97이다.Humidity ratio $\omega$: kg of water vapor per kg of dry air. The 0.622 in $\omega = 0.622\,p_v/(p-p_v)$ is the molecular weight ratio 18.02/28.97.
노점 $T_d$: $\omega$가 일정한 채 냉각할 때 처음 이슬이 맺히는 온도이다. 표면 온도가 $T_d$보다 낮은 면에서는 응축이 일어난다.Dew point $T_d$: the temperature at which dew first forms when cooling at constant $\omega$. Condensation occurs on any surface colder than $T_d$.
습구 온도 $T_{wb}$: 건구 온도 이하이며, $\phi = 100$ %일 때만 건구 온도와 같다. 건조할수록 건구와의 차이가 커진다.Wet-bulb temperature $T_{wb}$: never above the dry-bulb temperature and equal to it only at $\phi = 100$ %. The drier the air, the larger the gap.
Figure 12.3온도와 상대습도에 따른 습도비와 노점Humidity Ratio and Dew Point from Temperature and Relative Humidity
건구 온도 $T$ ($^{\circ}\mathrm{C}$)Dry-bulb $T$ ($^{\circ}\mathrm{C}$)25.0
상대습도 $\phi$ (%)Relative humidity $\phi$ (%)50
전체 압력 $p$ (kPa)Total pressure $p$ (kPa)101.3
포화압력 $p_g$ (kPa)$p_g$ (kPa)0
증기압 $p_v$ (kPa)$p_v$ (kPa)0
습도비 $\omega$ (g/kg)$\omega$ (g/kg)0
노점 ($^{\circ}\mathrm{C}$)Dew point ($^{\circ}\mathrm{C}$)0
엔탈피 (kJ/kg)Enthalpy (kJ/kg)0
$p_g$는 Magnus 식으로 계산했다. 회색 곡선은 $\phi$ = 20, 40, 60, 80 %이고 파란 곡선은 포화(100 %)이다. 빨간 점에서 왼쪽으로 가면 $\omega$가 일정한 냉각이며 포화 곡선과 만나는 온도가 노점이다. 같은 $\phi$에서도 온도가 높을수록 공기가 담는 수증기가 빠르게 늘어난다.$p_g$ is computed with the Magnus equation. Gray curves are $\phi$ = 20, 40, 60, 80 % and the blue curve is saturation (100 %). Going left from the red point is cooling at constant $\omega$, and the temperature where it meets the saturation curve is the dew point. At the same $\phi$ the vapor content rises steeply with temperature.
Section 12.7
습공기 선도Psychrometric Charts
습공기 선도는 정해진 압력에서 건구 온도 $T$를 가로축, 습도비 $\omega$를 세로축으로 하여 $\phi$, $T_d$, $T_{wb}$, $h$를 한 점에서 읽게 만든 그래프이다. 습공기의 상태는 압력이 정해지면 독립 변수 두 개로 결정되므로 점 하나가 상태 하나이다.A psychrometric chart plots dry-bulb temperature $T$ on the horizontal axis and humidity ratio $\omega$ on the vertical axis at a fixed pressure, so $\phi$, $T_d$, $T_{wb}$ and $h$ can be read from a single point. At a given pressure two independent properties fix the moist-air state, so one point is one state.
$\omega$가 일정한 수평선을 따라 온도를 올리면 $\phi$는 내려가고, 왼쪽으로 가면 올라가서 포화 곡선에서 멈춘다. 수평선이 포화 곡선과 만나는 점의 온도가 $T_d$이다. 정압 단열 포화 과정에 해당하는 $T_{wb}$ 일정선은 이 좌표에서 거의 직선이며 포화 곡선에서 오른쪽 아래로 뻗는다. 점에서 이 선을 포화 곡선까지 따라가면 $T_{wb}$를 읽는다.Raising the temperature along a horizontal line of constant $\omega$ lowers $\phi$, and moving left raises it until the saturation curve stops the line. The temperature where the horizontal line meets the saturation curve is $T_d$. Lines of constant $T_{wb}$, which follow adiabatic saturation, are nearly straight in these coordinates and run down and to the right from the saturation curve. Follow such a line from the point back to saturation to read $T_{wb}$.
Figure 12.4습공기 선도에서 상태점 읽기Reading a State Point on the Psychrometric Chart
예측: $\omega$를 일정하게 두고 건구 온도만 올리면 상대습도 $\phi$는 어떻게 될까?Predict: if $\omega$ is held constant and only the dry-bulb temperature rises, what happens to $\phi$?
목표: 처음 끄는 동안은 점이 가로 방향으로만 움직입니다(ω 고정). 그 뒤에는 자유롭게 끌 수 있습니다. 건구 온도 30 $^{\circ}\mathrm{C}$, 습구 온도 20 $^{\circ}\mathrm{C}$(각각 1 이내)에 점을 놓으세요.Goal: the first drag moves the point horizontally only (ω fixed). After that you can drag freely. Place the point at dry-bulb 30 $^{\circ}\mathrm{C}$ and wet-bulb 20 $^{\circ}\mathrm{C}$ (each within 1).
p = 101.325 kPa, 증기압은 Magnus 식이다. 파란 점선은 노점까지의 수평선이고 초록 점선은 습구 온도선이다. 건구와 습구의 차이가 클수록 공기가 건조하며, 포화 곡선 위에서는 세 온도가 모두 같다.p = 101.325 kPa and vapor pressure is from the Magnus equation. The blue dotted line is the horizontal path to the dew point and the green dotted line is the wet-bulb line. A larger gap between dry-bulb and wet-bulb means drier air, and on the saturation curve all three temperatures coincide.
Section 12.8
공기조화 과정의 해석Analyzing Air-Conditioning Processes
공기조화 장치는 정상 유동 장치이므로 건조 공기와 물 각각에 질량 수지를 쓰고, 습공기에 에너지 수지를 쓴다. 가열은 $\omega$가 일정한 수평 이동이다. 냉각은 코일 표면 온도가 입구 공기의 노점보다 높으면 같은 수평 이동이고, 낮으면 포화 곡선 쪽으로 기울어진 선을 따라 $\omega$가 줄면서 응축수가 생긴다.Air-conditioning equipment operates at steady state, so a mass balance is written for dry air and for water separately and an energy balance for the moist air. Heating is a horizontal move at constant $\omega$. Cooling is the same horizontal move if the coil surface is above the inlet dew point, and if it is below, the state follows a line tilted toward saturation while $\omega$ falls and condensate forms.
실제 코일은 모든 공기가 표면에 닿지 못하므로 출구 상태는 입구 상태와 장치 노점(apparatus dew point, ADP)을 잇는 직선 위에 있다. 입구 쪽 공기가 차지하는 비율을 bypass factor $\beta$라고 하며 출구는 ADP에서 입구 쪽으로 $\beta$만큼 떨어진 점이다. 응축수 유량은 $\dot{m}_a(\omega_1 - \omega_2)$이다.A real coil cannot touch all of the air, so the exit state lies on the straight line between the inlet state and the apparatus dew point (ADP). The fraction of air that bypasses the surface is the bypass factor $\beta$, and the exit sits $\beta$ of the way from the ADP toward the inlet. The condensate rate is $\dot{m}_a(\omega_1 - \omega_2)$.
서로 다른 두 공기 흐름이 단열 혼합하면 건조 공기, 수증기, 엔탈피가 모두 보존되어 혼합 상태가 두 입구 상태를 잇는 선분 위에 놓인다. 이 선은 $(\omega, h)$ 좌표에서 직선이다. 선분의 가운데 구간이 포화 곡선 바깥에 들어가면 혼합 직후 안개(fog)가 생긴다. 건조한 지역에서 쓰는 증발 냉각은 물을 분무해 $h$가 거의 일정한 채 $\omega$를 올리고 $T$를 낮춘다.When two air streams mix adiabatically, dry air, water vapor and enthalpy are all conserved, so the mixed state lies on the line segment joining the two inlet states. The line is straight in $(\omega, h)$ coordinates. If the middle part of the segment falls outside the saturation curve, fog forms on mixing. Evaporative cooling, used in dry climates, sprays water so that $\omega$ rises and $T$ falls at nearly constant $h$.
현열과 잠열: 온도를 바꾸는 열이 현열이고 수증기를 응축시키는 열이 잠열이다. 코일 표면이 노점보다 낮으면 둘이 함께 제거된다.Sensible and latent heat: sensible heat changes temperature and latent heat condenses vapor. A coil colder than the dew point removes both together.
혼합비: 혼합 상태는 건조 공기 질량 유량 비 $\dot{m}_{a1}/\dot{m}_{a2}$로 정해지며, 비는 선분을 나누는 비와 같다.Mixing ratio: the mixed state is fixed by the dry-air mass flow ratio $\dot{m}_{a1}/\dot{m}_{a2}$, which equals the ratio in which the segment is divided.
Figure 12.5냉각 코일의 응축수량과 냉각 부하Condensate Rate and Cooling Load of a Cooling Coil
예측: 입구 공기(30 $^{\circ}\mathrm{C}$, $\phi$ = 60 %, 노점 21.4 $^{\circ}\mathrm{C}$)를 노점보다 높은 온도의 코일로 냉각하면 응축수가 생길까?Predict: the inlet air (30 $^{\circ}\mathrm{C}$, $\phi$ = 60 %, dew point 21.4 $^{\circ}\mathrm{C}$) is cooled by a coil warmer than its dew point. Will condensate form?
목표: 포화 곡선 위의 초록 점(ADP)을 좌우로 끌어 코일 표면 온도를 바꾸세요. 먼저 노점보다 높은 위치에서 놓아 예측을 확인하고, 다음에 응축수가 11 kg/h 이상 13 kg/h 이하가 되게 맞추세요(건조 공기 1 kg/s).Goal: drag the green point (ADP) along the saturation curve to change the coil surface temperature. First release it above the dew point to check your prediction, then tune the condensate to 11 to 13 kg/h (dry air 1 kg/s).
$h_f = 4.186\,T_2$ kJ/kg로 계산했다. 코일 표면이 노점보다 높으면 $\omega$가 그대로여서 응축수는 0이고 부하는 모두 현열이다. 노점보다 낮아지면 응축수와 잠열이 함께 늘어서 같은 온도 강하에도 부하가 커진다.$h_f = 4.186\,T_2$ kJ/kg is used. If the coil surface is above the dew point, $\omega$ is unchanged, condensate is zero and the load is all sensible. Below the dew point, condensate and latent load grow together, so the same temperature drop costs more load.
Figure 12.6두 공기 흐름의 단열 혼합과 안개Adiabatic Mixing of Two Air Streams and Fog
예측: 겨울 외기(2 $^{\circ}\mathrm{C}$, 90 %)와 실내 공기(28 $^{\circ}\mathrm{C}$, 80 %)는 둘 다 포화 곡선 안쪽이다. 어떤 비율로 섞으면 혼합 공기가 포화 곡선 바깥으로 나가 안개가 생기는 구간이 있을까?Predict: winter outdoor air (2 $^{\circ}\mathrm{C}$, 90 %) and indoor air (28 $^{\circ}\mathrm{C}$, 80 %) are both inside the saturation curve. Is there a mixing ratio at which the mixture leaves the curve and forms fog?
목표: 혼합 점을 두 상태 사이에서 끌어 건조 공기 유량의 비를 바꾸세요. 안개 구간의 두 경계 중 한 곳에 점을 놓으세요(외기 비율 0.03 이내). 먼저 한 번 끌어 예측을 확인한 뒤에 시도하세요.Goal: drag the mixed point between the two states to change the dry-air flow ratio. Place it on either boundary of the fog region (within 0.03 of the outdoor-air fraction). Drag once first to check your prediction.
외기 : 실내 (건조 공기)Outdoor : indoor (dry air)0
혼합 $T_3$ ($^{\circ}\mathrm{C}$)Mixed $T_3$ ($^{\circ}\mathrm{C}$)0
혼합 $\omega_3$Mixed $\omega_3$0
상대습도 $\phi_3$$\phi_3$0
안개Fog없음None
혼합 상태는 $(\omega, h)$ 좌표에서 두 입구 상태를 잇는 직선 위에 있고, 이 좌표에서 직선이다. 포화 곡선은 위로 볼록하므로 선분의 가운데는 곡선 바깥으로 나갈 수 있다. 빨간 구간이 안개 구간이며, 이 구간의 혼합 공기는 포화 상태로 돌아가면서 남는 수증기가 작은 물방울이 된다.The mixed state lies on the straight line between the inlet states in $(\omega, h)$, and it looks nearly straight on this chart. The saturation curve is convex upward, so the middle of the segment can fall outside it. The red section is the fog region, where mixed air returns to saturation and the excess vapor becomes small droplets.
Section 12.9
냉각탑Cooling Towers
냉각탑은 발전소와 공조 장치의 응축기에서 데워진 물을 공기와 직접 접촉시켜 식힌다. 따뜻한 물이 위에서 분무되고 공기가 아래에서 위로 흐르면(향류), 물의 일부가 증발하면서 나머지 물이 냉각된다. 증발로 잃은 만큼의 보충수(make-up water)를 넣어야 한다.A cooling tower cools water warmed in a power plant or air-conditioning condenser by direct contact with air. Warm water is sprayed from the top while air flows upward (counterflow), and part of the water evaporates while the rest cools. Make-up water must replace what evaporates.
공기 쪽 에너지 수지는 $\dot{m}_a(h_2 - h_1) = \dot{m}_w c_w (T_{w,in} - T_{w,out})$이고 보충수는 $\dot{m}_a(\omega_2 - \omega_1)$이다. 이 식만으로는 출구 수온이 정해지지 않으며, 공기 출구 상태와 접촉 면적이 함께 필요하다. 아래 그림은 Merkel 모델을 쓴다. 각 높이에서 물과 공기 사이 엔탈피 차이가 구동력이고, 적분값 $\int c_w\,dT/(h_s - h_a)$이 장치 크기로 정해지는 NTU와 같아야 한다.The air-side energy balance is $\dot{m}_a(h_2 - h_1) = \dot{m}_w c_w (T_{w,in} - T_{w,out})$ and the make-up is $\dot{m}_a(\omega_2 - \omega_1)$. These alone do not fix the outlet water temperature, which also depends on the exit air state and the contact area. The figure below uses the Merkel model. The enthalpy difference between water and air at each height is the driving force, and the integral $\int c_w\,dT/(h_s - h_a)$ must equal the NTU set by the tower size.
냉각수는 입구 공기의 습구 온도보다 낮게 식힐 수 없다. 공기 유량을 늘리면 출구 수온이 내려가지만, NTU가 정해져 있으므로 한없이 내려가지는 않고 습구 온도에 접근하는 정도(approach)가 한계가 된다. 이 그림은 입구 공기를 25 $^{\circ}\mathrm{C}$, $\phi$ = 50 %로 두고 출구 공기를 포화 상태로 가정한다.Water cannot be cooled below the inlet-air wet-bulb temperature. More air lowers the outlet water temperature, but with a fixed NTU it does not fall indefinitely, and the approach to the wet-bulb temperature sets the limit. The figure takes inlet air at 25 $^{\circ}\mathrm{C}$, $\phi$ = 50 % and assumes saturated exit air.
Approach: 출구 수온과 입구 공기의 습구 온도의 차이이다. 작을수록 큰 탑이 필요하다.Approach: the difference between the outlet water temperature and the inlet-air wet-bulb temperature. A smaller approach needs a larger tower.
Range: 입구와 출구 수온의 차이이며 탑이 제거하는 열량을 정한다.Range: the difference between inlet and outlet water temperature, which sets the heat the tower removes.
Figure 12.7공기 유량에 따른 냉각탑 출구 수온Cooling Tower Outlet Water Temperature versus Air Flow
예측: 물 유량과 입구 수온(40 $^{\circ}\mathrm{C}$)을 고정하고 공기 유량을 늘리면 출구 수온은 어떻게 될까?Predict: with the water flow and inlet water temperature (40 $^{\circ}\mathrm{C}$) fixed, what happens to the outlet water temperature when the air flow increases?
목표: 그림 오른쪽의 공기 유량 막대를 위아래로 끌어 출구 수온을 27 $\pm$ 0.4 $^{\circ}\mathrm{C}$로 맞추세요. 출구 수온을 습구 온도(17.9 $^{\circ}\mathrm{C}$)까지 낮출 수 있는지도 확인하세요.Goal: drag the air-flow bar on the right of the figure up and down to set the outlet water temperature to 27 $\pm$ 0.4 $^{\circ}\mathrm{C}$. Also check whether it can reach the wet-bulb temperature (17.9 $^{\circ}\mathrm{C}$).
공기 유량 (kg/s)Air flow (kg/s)0
출구 수온 ($^{\circ}\mathrm{C}$)Outlet water ($^{\circ}\mathrm{C}$)0
Approach (K)Approach (K)0
출구 공기 ($^{\circ}\mathrm{C}$)Exit air ($^{\circ}\mathrm{C}$)0
보충수 (kg/h)Make-up (kg/h)0
물 1 kg/s, NTU = 1.2, 입구 공기 25 $^{\circ}\mathrm{C}$, $\phi$ = 50 %로 Merkel 적분을 수치로 풀었고(h_s는 Magnus 식), 보충수 엔탈피는 무시했다. 공기가 많아질수록 출구 수온은 25 $^{\circ}\mathrm{C}$ 근처에서 더 내려가지 않는다. 습구 온도까지 내리려면 NTU, 즉 탑이 훨씬 커야 한다.The Merkel integral is solved numerically for 1 kg/s of water, NTU = 1.2 and inlet air at 25 $^{\circ}\mathrm{C}$, $\phi$ = 50 % (h_s from the Magnus equation), and make-up enthalpy is neglected. With more air the outlet water stops falling near 25 $^{\circ}\mathrm{C}$. Reaching the wet-bulb temperature needs a much larger NTU, that is, a larger tower.
Self-Check
확인 문제Quiz
Q1. N2 1 kmol과 CO2 1 kmol의 혼합물에서 CO2의 질량분율은? ($M_{N_2} = 28.01$, $M_{CO_2} = 44.01$ kg/kmol)Q1. What is the mass fraction of CO2 in a mixture of 1 kmol N2 and 1 kmol CO2? ($M_{N_2} = 28.01$, $M_{CO_2} = 44.01$ kg/kmol)
몰분율은 각각 0.5이므로 $M = 0.5(28.01) + 0.5(44.01) = 36.01$ kg/kmol이다. $mf_{CO_2} = y M_{CO_2}/M = 0.5(44.01)/36.01 = 0.611$이다. 무거운 성분은 질량분율이 몰분율보다 크다.The mole fractions are 0.5 each, so $M = 0.5(28.01) + 0.5(44.01) = 36.01$ kg/kmol and $mf_{CO_2} = y M_{CO_2}/M = 0.5(44.01)/36.01 = 0.611$. A heavy component has a mass fraction above its mole fraction.
Q2. 전체 압력 2 bar인 이상기체 혼합물에서 몰분율 0.25인 성분의 분압은?Q2. In an ideal gas mixture at a total pressure of 2 bar, what is the partial pressure of a component with mole fraction 0.25?
Dalton 모델의 $p_i = y_i p = 0.25 \times 2 = 0.5$ bar이다. 분체적 분율도 같은 0.25이다.From the Dalton model, $p_i = y_i p = 0.25 \times 2 = 0.5$ bar. The partial-volume fraction is also 0.25.
Q3. 30 $^{\circ}\mathrm{C}$, $\phi$ = 60 %인 공기(노점 21.4 $^{\circ}\mathrm{C}$)를 $\omega$가 일정하게 25 $^{\circ}\mathrm{C}$까지 냉각한다. 어떻게 되는가?Q3. Air at 30 $^{\circ}\mathrm{C}$, $\phi$ = 60 % (dew point 21.4 $^{\circ}\mathrm{C}$) is cooled to 25 $^{\circ}\mathrm{C}$ at constant $\omega$. What happens?
25 $^{\circ}\mathrm{C}$는 노점 21.4 $^{\circ}\mathrm{C}$보다 높으므로 응축하지 않는다. $p_v$는 그대로이고 $p_g$가 4.24 kPa에서 3.16 kPa로 줄어 $\phi = 0.60 \times 4.24/3.16 = 0.80$이다.25 $^{\circ}\mathrm{C}$ is above the 21.4 $^{\circ}\mathrm{C}$ dew point, so nothing condenses. $p_v$ is unchanged while $p_g$ falls from 4.24 to 3.16 kPa, so $\phi = 0.60 \times 4.24/3.16 = 0.80$.
What If?
만약에?What If?
만약 칸막이 양쪽이 같은 기체이고 $T$와 $p$도 같다면?What if both sides of the partition hold the same gas at the same $T$ and $p$?
클릭하여 확인 →Click to reveal →
칸막이를 제거해도 거시적 상태가 바뀌지 않으므로 $\Delta S = 0$이다. 혼합 엔트로피 식 $-\bar{R}\sum y_i\ln y_i$는 기체를 구별할 수 있을 때만 성립한다. 기체가 조금이라도 다르면 식의 값이 그대로 나타난다는 점이 Gibbs 역설로 알려져 있으며, 구별 가능 여부가 엔트로피의 정의에 들어간다.Removing the partition changes no macroscopic state, so $\Delta S = 0$. The formula $-\bar{R}\sum y_i\ln y_i$ holds only when the gases can be told apart. That the full value appears for even slightly different gases is the Gibbs paradox, and distinguishability enters the definition of entropy.
만약 상대습도가 100 %인 공기라면 건구, 습구, 노점은?What if the air is at 100 % relative humidity: how do dry-bulb, wet-bulb and dew point compare?
클릭하여 확인 →Click to reveal →
세 온도가 모두 같다. 이미 포화이므로 젖은 심지에서 더 증발할 수 없어 습구 온도가 내려가지 않고, 냉각을 시작하면 바로 응축이 일어나므로 노점도 건구 온도와 같다. 그림 12.4에서 점을 포화 곡선 위에 올려 확인할 수 있다.All three are equal. The air is already saturated, so the wet wick cannot evaporate more and the wet-bulb does not drop, and condensation begins at once on cooling, so the dew point equals the dry-bulb. Put the point on the saturation curve in Figure 12.4 to see it.
만약 냉각탑의 NTU를 크게 늘리면 물을 건구 온도보다 낮게 식힐 수 있을까?What if the tower NTU is made very large: can the water be cooled below the dry-bulb temperature?
클릭하여 확인 →Click to reveal →
가능하다. 증발이 열을 가져가므로 건구 온도 아래로 내려가며, 하한은 입구 공기의 습구 온도이다. 이 그림의 공기(건구 25 $^{\circ}\mathrm{C}$, 습구 17.9 $^{\circ}\mathrm{C}$)에서는 NTU와 공기 유량을 충분히 키우면 출구 수온이 17.9 $^{\circ}\mathrm{C}$에 한없이 가까워진다. 습구 온도에 도달하려면 탑이 무한히 커야 한다.Yes. Evaporation carries heat away, so the water can fall below the dry-bulb temperature, down to the inlet-air wet-bulb temperature as the floor. For the air in this figure (dry-bulb 25 $^{\circ}\mathrm{C}$, wet-bulb 17.9 $^{\circ}\mathrm{C}$), enough NTU and air flow bring the outlet water arbitrarily close to 17.9 $^{\circ}\mathrm{C}$. Reaching it would take an infinitely large tower.
Key Takeaways
01
몰분율 하나로 정해지는 분압Partial Pressure from Mole Fraction
이상기체 혼합물에서 $p_i = y_i p$이고 $V_i = y_i V$이다. 질량 기준 자료는 분자량으로 몰분율로 바꾼 뒤 쓴다.In an ideal gas mixture $p_i = y_i p$ and $V_i = y_i V$. Convert mass-based data to mole fractions with molecular weights first.
02
혼합은 엔트로피를 늘린다Mixing Raises Entropy
$u$와 $h$는 성분의 합이지만 $s$는 분압에서 계산한다. 서로 다른 기체의 혼합은 $-\bar{R}\sum y_i\ln y_i$만큼 엔트로피가 늘고 비가역이다.$u$ and $h$ are sums over components, but $s$ is evaluated at partial pressures. Mixing different gases raises entropy by $-\bar{R}\sum y_i\ln y_i$ and is irreversible.
03
습공기 상태는 점 하나One Point per Moist-Air State
압력이 정해지면 $T$와 $\omega$ 두 값으로 $\phi$, $T_d$, $T_{wb}$, $h$가 모두 정해진다. 냉각은 노점보다 높으면 수평 이동이고 낮으면 응축수가 생긴다.At a given pressure $T$ and $\omega$ fix $\phi$, $T_d$, $T_{wb}$ and $h$. Cooling is a horizontal move above the dew point and forms condensate below it.
04
습구 온도가 냉각의 하한Wet-Bulb Is the Cooling Floor
단열 혼합은 두 상태를 잇는 선분 위에서 일어나며 안개가 생길 수 있다. 냉각탑과 증발 냉각은 습구 온도 아래로 내려가지 못한다.Adiabatic mixing lies on the segment between the states and may form fog. Cooling towers and evaporative coolers cannot go below the wet-bulb temperature.