Moran, Fundamentals of Engineering Thermodynamics, Chapter 11. 슬라이더를 움직이면 그래프가 실시간으로 반응합니다.Moran, Fundamentals of Engineering Thermodynamics, Chapter 11. Move the sliders to see the graphs respond in real time.
상태방정식Maxwell 관계식Clapeyron 방정식Joule-Thomson 계수일반화 선도혼합물과 Kay 규칙Fugacity
Section 11.1
상태방정식 사용하기Using Equations of State
이상기체 식 $pv = RT$는 압력이 낮고 온도가 높을 때만 맞는다. 실제 기체의 $p$-$v$-$T$ 관계는 상태방정식으로 나타내며, 상수가 두 개인 식부터 수십 개인 식까지 있다. 상수가 적은 식은 계산이 간단하지만 적용 범위가 좁고, 상수가 많은 식은 넓은 범위에서 정확하지만 계산이 번거롭다. 두 상수 식의 상수는 임계점 데이터에서 정한다.The ideal gas law $pv = RT$ holds only at low pressure and high temperature. Real-gas $p$-$v$-$T$ behavior is described by equations of state with anywhere from two to dozens of constants. Few-constant equations are simple but cover a narrow range; many-constant equations are accurate over a wide range but laborious. The constants of two-constant equations are fixed from critical-point data.
van der Waals 식은 분자 부피를 보정하는 $b$와 분자 사이 인력을 보정하는 $a$를 쓴다. 임계점에서 $(\partial p/\partial v)_T = 0$과 $(\partial^2 p/\partial v^2)_T = 0$이 함께 성립해야 한다는 조건에서 $a$와 $b$가 임계 온도와 임계 압력으로 정해진다. Redlich-Kwong 식은 인력 항에 온도 의존성을 넣어 정확도를 높인다. 이 식들은 임계점을 가진다는 점에서 이상기체 식과 다르다.The van der Waals equation uses $b$ to correct for molecular volume and $a$ to correct for intermolecular attraction. Requiring $(\partial p/\partial v)_T = 0$ and $(\partial^2 p/\partial v^2)_T = 0$ at the critical point fixes $a$ and $b$ from the critical temperature and pressure. The Redlich-Kwong equation adds a temperature dependence to the attraction term for better accuracy. Unlike the ideal gas law, these equations have a critical point.
$$p = \frac{RT}{v-b} - \frac{a}{v^{2}}, \qquad a = \frac{27R^{2}T_c^{2}}{64\,p_c}, \qquad b = \frac{RT_c}{8\,p_c}$$
$$p = \frac{RT}{v-b} - \frac{a}{v\,(v+b)\,T^{1/2}}, \qquad a = 0.42748\,\frac{R^{2}T_c^{5/2}}{p_c}, \qquad b = 0.08664\,\frac{RT_c}{p_c}$$
van der Waals 식: 임계 압축성 인자가 모든 물질에서 $Z_c = 3/8 = 0.375$로 같다. 실제 값은 대부분 0.23부터 0.31까지이므로 정량 정확도는 낮다.van der Waals equation: it predicts the same critical compressibility $Z_c = 3/8 = 0.375$ for every substance, while real values are mostly 0.23 to 0.31, so quantitative accuracy is limited.
비리얼 전개: $Z$를 $1/v$ 또는 $p$의 급수로 나타낸다. 비리얼 계수는 통계열역학으로 분자 간 힘과 연결된다.Virial expansion: $Z$ is a series in $1/v$ or $p$. Statistical thermodynamics links the virial coefficients to intermolecular forces.
대응 상태 원리: 환산 온도 $T_R$과 환산 압력 $p_R$이 같으면 여러 기체의 $Z$가 거의 같다. 일반화 압축성 선도가 이 원리를 이용한다.Principle of corresponding states: gases at the same reduced temperature $T_R$ and reduced pressure $p_R$ have nearly the same $Z$. The generalized compressibility chart rests on this principle.
Figure 11.1van der Waals 식의 $a$, $b$와 등온선van der Waals Constants $a$, $b$ and Isotherms
$a$ 배율 (CO2 값 기준)$a$ scale (relative to CO2)1.00
$b$ 배율 (CO2 값 기준)$b$ scale (relative to CO2)1.00
온도 $T$ (K)Temperature $T$ (K)270
$T_c$ (K)$T_c$ (K)—
$p_c$ (MPa)$p_c$ (MPa)—
$v_c$ (L/kg)$v_c$ (L/kg)—
$Z_c$$Z_c$—
등온선 형태Isotherm shape—
$a$와 $b$ 배율 1.00은 CO2의 임계 데이터 ($T_c$ = 304.2 K, $p_c$ = 7.39 MPa, $R$ = 0.1889 kJ/(kg K))에서 구한 값이다. $a$를 키우면 $T_c$와 $p_c$가 함께 커지고, $b$를 키우면 $T_c$와 $p_c$가 모두 줄며 $v_c = 3b$가 커진다. $Z_c$는 $a$와 $b$를 어떻게 바꿔도 0.375로 남는다.Scale 1.00 corresponds to CO2 critical data ($T_c$ = 304.2 K, $p_c$ = 7.39 MPa, $R$ = 0.1889 kJ/(kg K)). Raising $a$ raises both $T_c$ and $p_c$; raising $b$ lowers both and increases $v_c = 3b$. $Z_c$ stays at 0.375 for any $a$ and $b$.
Figure 11.2일반화 압축성 선도에서 $Z$ 읽기Reading $Z$ from the Generalized Compressibility Chart
예측: 아래 기체의 $Z$는 1보다 작을까, 클까?Predict: Will $Z$ of the gas below be less than 1 or greater than 1?
목표: $T_R$와 $p_R$를 계산한 뒤, 선도 위의 점을 끌어 $Z$를 2% 안에서 읽으세요.Goal: Compute $T_R$ and $p_R$, then drag the point on the chart to read $Z$ within 2%.
기체Gas—
$T$ (K), $p$ (bar)$T$ (K), $p$ (bar)—
$T_c$ (K), $p_c$ (bar)$T_c$ (K), $p_c$ (bar)—
찍은 점 ($p_R$, $Z$)Marked point ($p_R$, $Z$)—
오차Error—
곡선은 Lee-Kesler 단순 유체 상태방정식으로 계산한 $Z^{(0)}$이며, Moran의 Fig. A-1과 같은 형태의 선도를 이 식으로 다시 그린 것이다. 각 기체의 $T_c$와 $p_c$는 부록 표 A-1 값을 반올림했다. 같은 $T_R$ 곡선 위에서 $p_R$가 커지면 $Z$가 먼저 1 아래로 내려갔다가 다시 올라가며, 인력이 큰 구간과 반발이 큰 구간이 이 곡선의 극소점에서 구분된다.The curves are $Z^{(0)}$ from the Lee-Kesler simple-fluid equation, redrawn in the form of Moran's Fig. A-1. $T_c$ and $p_c$ are rounded values from Appendix Table A-1. Along one $T_R$ curve, $Z$ first falls below 1 as $p_R$ rises and then climbs again; the minimum separates the attraction-dominated range from the repulsion-dominated range.
Section 11.3
열역학 관계식 유도: Maxwell 관계식과 Clapeyron 방정식Developing Property Relations: Maxwell Relations and the Clapeyron Equation
상태량 $z = z(x, y)$의 미분 $dz = M\,dx + N\,dy$가 완전 미분이면 $(\partial M/\partial y)_x = (\partial N/\partial x)_y$가 성립한다. 내부에너지 $u$, 엔탈피 $h$, Helmholtz 함수 $\psi = u - Ts$, Gibbs 함수 $g = h - Ts$는 모두 상태량이므로 각각의 미분에 이 조건을 적용할 수 있다. 이렇게 얻는 네 식이 Maxwell 관계식이며, 측정하기 어려운 엔트로피의 편미분을 $p$, $v$, $T$의 편미분으로 바꾼다.If the differential $dz = M\,dx + N\,dy$ of a property $z(x, y)$ is exact, then $(\partial M/\partial y)_x = (\partial N/\partial x)_y$. Internal energy $u$, enthalpy $h$, the Helmholtz function $\psi = u - Ts$ and the Gibbs function $g = h - Ts$ are all properties, so the condition applies to each of their differentials. The four results are the Maxwell relations; they replace hard-to-measure entropy derivatives with derivatives of $p$, $v$ and $T$.
포화 상태에서 압력은 온도만의 함수이다. 같은 온도와 압력에서 포화 액체와 포화 증기의 Gibbs 함수가 같으므로 $g_f = g_g$이다. 등온 과정에서 $dg = v\,dp$이므로 $\int_f^g v\,dp = 0$이 되고, $p$-$v$ 선도에서 van der Waals 등온선과 수평선이 만드는 두 면적이 같아야 한다는 Maxwell 등면적 구성이 나온다. 온도를 조금 바꿀 때 같은 조건이 유지되는 것으로부터 Clapeyron 방정식이 나온다.At saturation the pressure depends on temperature alone. At the same $T$ and $p$ the saturated liquid and vapor have equal Gibbs functions, $g_f = g_g$. Along an isotherm $dg = v\,dp$, so $\int_f^g v\,dp = 0$, which is the Maxwell equal-area construction: on a $p$-$v$ diagram the two areas between the van der Waals isotherm and the horizontal line must be equal. Keeping this condition while changing the temperature slightly gives the Clapeyron equation.
Clapeyron 방정식: 증기압 곡선의 기울기를 상변화 엔탈피와 비체적 변화로 나타낸다. $h_{fg}$와 $v_{fg}$는 측정이 쉬워서 곡선의 기울기를 직접 구하는 데 쓴다.Clapeyron equation: it expresses the slope of the vapor-pressure curve through the phase-change enthalpy and volume change. Both $h_{fg}$ and $v_{fg}$ are easy to measure, so the equation yields the slope directly.
Clausius-Clapeyron 근사: $v_g \gg v_f$이고 증기를 이상기체로 보며 $h_{fg}$를 상수로 두면 $\ln p$가 $1/T$에 대해 직선이 된다.Clausius-Clapeyron approximation: with $v_g \gg v_f$, ideal-gas vapor and constant $h_{fg}$, $\ln p$ is a straight line in $1/T$.
Figure 11.3Maxwell 등면적 구성과 포화 압력Maxwell Equal-Area Construction and Saturation Pressure
예측: $T_R = 0.90$에서 포화 압력은 등온선의 극솟값과 극댓값의 산술 평균보다 위일까, 아래일까?Predict: At $T_R = 0.90$, is the saturation pressure above or below the arithmetic mean of the isotherm's local minimum and maximum?
목표: 수평선을 위아래로 끌어 파란 면적과 빨간 면적을 같게 만드세요. 포화 압력과 2% 안에 들어오면 성공입니다.Goal: Drag the horizontal line up or down until the blue and red areas are equal. Success is within 2% of the saturation pressure.
환산 온도 $T_R$Reduced temperature $T_R$0.90
선의 압력 $p_R$Line pressure $p_R$—
파란 면적Blue area—
빨간 면적Red area—
포화 압력 $p_R^{sat}$Saturation pressure $p_R^{sat}$—
환산 형태 $p_R = 8T_R/(3v_R - 1) - 3/v_R^2$를 쓴다. 두 면적이 같아지는 압력이 포화 압력이며, 극솟값과 극댓값의 평균과 다른 값이다. $T_R$를 1에 가깝게 올리면 액체와 증기의 비체적 차이가 줄어들어 두 근이 한 점으로 모인다.The reduced form $p_R = 8T_R/(3v_R - 1) - 3/v_R^2$ is used. The pressure that equalizes the areas is the saturation pressure, which differs from the mean of the extrema. As $T_R$ approaches 1 the liquid and vapor volumes converge and the two outer roots merge at one point.
Figure 11.4물의 증기압 곡선 기울기와 Clapeyron 방정식Slope of the Water Vapor-Pressure Curve and the Clapeyron Equation
예측: 포화 온도를 100 °C에서 200 °C로 올리면 $dp/dT$는 몇 배가 될까?Predict: If the saturation temperature rises from 100 °C to 200 °C, by what factor does $dp/dT$ change?
목표: 곡선 위의 점을 끌어 기울기 $dp/dT$가 10 kPa/K (오차 5% 이내)인 온도를 찾으세요.Goal: Drag the point along the curve to find the temperature where $dp/dT$ is 10 kPa/K (within 5%).
곡선은 Wagner 증기압 식으로 그렸고, 기울기는 이 곡선을 수치 미분한 값이다. $h_{fg}$와 $v_{fg}$는 증기표의 10, 20, 50, 100, 150, 200, 250, 300, 350, 360 °C 값을 보간했다 (보간 오차 때문에 비율이 1에서 몇 % 벗어난다). 곡선의 기울기가 열역학 데이터 두 개의 비와 일치하므로, 증기표의 $p$-$T$ 열은 $h_{fg}$와 $v_{fg}$ 열과 서로 독립이 아니다.The curve is drawn from the Wagner vapor-pressure equation and the slope is its numerical derivative. $h_{fg}$ and $v_{fg}$ are interpolated from steam-table values at 10, 20, 50, 100, 150, 200, 250, 300, 350 and 360 °C (interpolation error moves the ratio a few percent from 1). The slope equals a ratio of two thermodynamic data, so the $p$-$T$ column of the steam table is not independent of its $h_{fg}$ and $v_{fg}$ columns.
Section 11.4
$p$-$v$-$T$ 데이터로 $u$, $h$, $s$의 변화 구하기Evaluating Changes in $u$, $h$ and $s$ from $p$-$v$-$T$ Data
$u$, $h$, $s$를 표로 구할 수 없는 기체는 상태방정식과 이상기체 비열 $c_v^*(T)$ 또는 $c_p^*(T)$로 변화량을 계산한다. 먼저 $u = u(T, v)$로 놓고 전미분을 쓰며, 계수의 편미분을 Maxwell 관계식으로 $p$-$v$-$T$ 관계의 편미분으로 바꾼다. $h = h(T, p)$로 놓아도 같은 방식이 된다.For gases whose $u$, $h$ and $s$ are not tabulated, changes are computed from an equation of state and the ideal-gas specific heat $c_v^*(T)$ or $c_p^*(T)$. Write $u = u(T, v)$, take the total differential, and use a Maxwell relation to turn the coefficient derivative into a derivative of the $p$-$v$-$T$ relation. The same approach works with $h = h(T, p)$.
상태량 변화는 경로에 따르지 않으므로 적분 경로를 편한 대로 잡는다. 보통 압력이 0에 가까운 이상기체 상태까지 등온으로 가고, 거기서 온도를 바꾸고, 다시 같은 온도에서 목표 압력까지 돌아오는 경로를 쓴다. 이상기체에서는 $T(\partial p/\partial T)_v = p$이므로 $v$에 대한 적분 항이 0이 되고 $du = c_v\,dT$로 돌아간다. van der Waals 기체에서는 $T(\partial p/\partial T)_v - p = a/v^2$이므로 등온 변화에서 다음이 성립한다.Property changes are path independent, so the integration path can be chosen freely. A common choice goes isothermally to the ideal-gas limit near zero pressure, changes temperature there, and returns isothermally to the final pressure. For an ideal gas $T(\partial p/\partial T)_v = p$, the $v$ integral vanishes, and $du = c_v\,dT$ is recovered. For a van der Waals gas $T(\partial p/\partial T)_v - p = a/v^2$, so along an isotherm the following holds.
내부에너지 변화의 의미: $a>0$이면 팽창($v_2 > v_1$) 때 $u$가 올라간다. 분자 사이 인력을 거슬러 분자를 떼어놓는 일이 필요하기 때문이다.Meaning of the internal-energy change: for $a>0$, $u$ rises on expansion ($v_2 > v_1$), because work is needed to pull molecules apart against attraction.
엔트로피 변화의 의미: 분자가 차지할 수 있는 부피 $v - b$가 늘어난 비율의 로그가 $\Delta s$이다. 분자 부피 보정 $b$만 엔트로피에 들어온다.Meaning of the entropy change: $\Delta s$ is the logarithm of the ratio of available volume $v - b$. Only the molecular-volume correction $b$ enters the entropy.
필요한 입력: $p$-$v$-$T$ 식과 한 점에서의 $c_p^*(T)$만 있으면 $\Delta u$, $\Delta h$, $\Delta s$를 모두 구할 수 있다. 증기표를 만드는 방법도 이 관계식에 바탕을 둔다.Required inputs: a $p$-$v$-$T$ equation and the single function $c_p^*(T)$ suffice to get $\Delta u$, $\Delta h$ and $\Delta s$. Steam-table construction rests on the same relations.
Section 11.5
비열 관계식과 Joule-Thomson 계수Specific Heat Relations and the Joule-Thomson Coefficient
$c_p$는 측정하기 쉬운데 $c_v$는 측정하기 어려운 경우가 많다. 두 비열의 차이를 체적 팽창계수 $\beta = \frac{1}{v}(\partial v/\partial T)_p$와 등온 압축률 $\kappa = -\frac{1}{v}(\partial v/\partial p)_T$로 나타내면 $c_v$를 $c_p$와 $p$-$v$-$T$ 측정값에서 구할 수 있다. $\kappa>0$이므로 $c_p \ge c_v$이고, $T \to 0$ 또는 비압축성 물질에서는 $\beta \to 0$이어서 두 비열이 같아진다.$c_p$ is easy to measure while $c_v$ often is not. Expressing the difference through the volume expansivity $\beta = \frac{1}{v}(\partial v/\partial T)_p$ and the isothermal compressibility $\kappa = -\frac{1}{v}(\partial v/\partial p)_T$ gives $c_v$ from $c_p$ and $p$-$v$-$T$ data. Since $\kappa>0$, $c_p \ge c_v$; as $T \to 0$ or for an incompressible substance $\beta \to 0$ and the two coincide.
교축 과정은 엔탈피가 일정하다. 교축 전후의 온도 변화율을 Joule-Thomson 계수 $\mu_J = (\partial T/\partial p)_h$로 정의한다. $\mu_J>0$이면 압력이 내려갈 때 온도도 내려가므로 냉각에 쓸 수 있고, $\mu_J<0$이면 온도가 올라간다. $\mu_J = 0$인 상태를 이은 곡선이 역전 곡선이며, 이상기체는 모든 상태에서 $\mu_J = 0$이다.A throttling process is isenthalpic. The temperature change per pressure drop is the Joule-Thomson coefficient $\mu_J = (\partial T/\partial p)_h$. If $\mu_J>0$ the temperature falls as pressure falls, which is useful for cooling; if $\mu_J<0$ the temperature rises. States with $\mu_J = 0$ form the inversion curve, and an ideal gas has $\mu_J = 0$ everywhere.
역전 온도: 영압력에서 van der Waals 기체의 상한 역전 온도는 $2a/(Rb) = 6.75\,T_c$이다. 수소와 헬륨은 이 온도가 실온보다 낮아서 실온에서 교축하면 가열된다.Inversion temperature: at zero pressure the upper inversion temperature of a van der Waals gas is $2a/(Rb) = 6.75\,T_c$. For hydrogen and helium it lies below room temperature, so throttling at room temperature heats them.
음속: $c = \sqrt{-v^2(\partial p/\partial v)_s}$이며 $k$와 등온 압축률로 $c = \sqrt{k\,v/\kappa}$로 쓸 수 있다.Speed of sound: $c = \sqrt{-v^2(\partial p/\partial v)_s}$, which equals $c = \sqrt{k\,v/\kappa}$ in terms of $k$ and the isothermal compressibility.
Figure 11.5van der Waals 기체의 $c_p - c_v$와 압력$c_p - c_v$ of a van der Waals Gas versus Pressure
온도 $T$ (K)Temperature $T$ (K)320
압력 $p$ (MPa)Pressure $p$ (MPa)7.0
$v$ (L/kg)$v$ (L/kg)—
$Z$$Z$—
$(c_p - c_v)/R$$(c_p - c_v)/R$—
$c_p - c_v$ (kJ/(kg K))$c_p - c_v$ (kJ/(kg K))—
CO2의 임계 데이터로 정한 van der Waals 식에서 $c_p - c_v = R/[1 - 2a(v-b)^2/(RTv^3)]$를 계산했다. 낮은 압력에서는 $R$에 가까워 이상기체 결과와 같고, $T_c$ 근처의 임계 압력에서는 $(\partial p/\partial v)_T \to 0$이어서 값이 급격히 커진다 (그림에서는 12R로 잘랐다). $T \lt T_c$에서는 상변화가 일어나는 압력에서 곡선이 끊긴다.Computed from the van der Waals equation with CO2 critical constants using $c_p - c_v = R/[1 - 2a(v-b)^2/(RTv^3)]$. At low pressure the value approaches $R$ as for an ideal gas; near the critical state $(\partial p/\partial v)_T \to 0$ and the value grows sharply (clipped at 12R in the plot). For $T \lt T_c$ the curve breaks at the pressure where the phase change occurs.
Figure 11.6Joule-Thomson 역전 곡선과 교축 시 온도 변화Joule-Thomson Inversion Curve and Temperature Change on Throttling
예측: 점이 있는 상태 ($T_R = 5.5$, $p_R = 7.5$)에서 압력을 낮추는 교축을 하면 온도는 어떻게 될까?Predict: Throttling to a lower pressure from the state shown ($T_R = 5.5$, $p_R = 7.5$), what happens to the temperature?
목표: $T_R \ge 4$인 상태 중에서 교축하면 온도가 내려가는 상태를 찾으세요. 점을 끌어 옮기고 교축 버튼을 누르세요.Goal: Find a state with $T_R \ge 4$ whose temperature falls on throttling. Drag the point, then press the throttle button.
van der Waals 기체 ($c_v = 2.5R$)의 역전 곡선은 $T_R = 6.75(1-x)^2$, $p_R = 54x - 81x^2$ ($0 \le x \le 2/3$)이다. 교축 경로는 $h = c_vT + RTv/(v-b) - 2a/v$를 일정하게 두고 푼 등엔탈피선이며, N2 환산은 $T_c$ = 126.2 K를 곱한 값이다. 곡선 아래쪽 영역에서는 $\mu_J>0$이어서 냉각되고, 위쪽과 오른쪽에서는 가열된다. 압력을 크게 낮추면 등엔탈피선이 역전 곡선을 가로질러 온도 방향이 바뀐다.The inversion curve of the van der Waals gas ($c_v = 2.5R$) is $T_R = 6.75(1-x)^2$, $p_R = 54x - 81x^2$ ($0 \le x \le 2/3$). The throttling path is the isenthalp from holding $h = c_vT + RTv/(v-b) - 2a/v$ constant; N2 values multiply by $T_c$ = 126.2 K. Below the curve $\mu_J>0$ and the gas cools; above and to the right it heats. A large pressure drop carries the isenthalp across the inversion curve and reverses the direction of the temperature change.
Section 11.7
엔탈피와 엔트로피의 일반화 선도Generalized Charts for Enthalpy and Entropy
$\Delta h$와 $\Delta s$를 구할 때 모든 기체에 상태방정식을 따로 쓸 수는 없다. 같은 온도와 압력의 실제 기체와 이상기체의 엔탈피와 엔트로피 차이를 편차(departure)라 하고, 이를 $T_R$와 $p_R$의 함수로 만든 것이 일반화 선도이다. 이상기체 항은 $c_p^*(T)$로, 편차 항은 선도로 구한다.One cannot use a separate equation of state for every gas when computing $\Delta h$ and $\Delta s$. The difference in enthalpy and entropy between the real gas and the ideal gas at the same $T$ and $p$ is the departure, and plotting it against $T_R$ and $p_R$ gives the generalized charts. The ideal-gas part comes from $c_p^*(T)$ and the departure part from the charts.
편차의 부호: 같은 $T$와 $p$에서 실제 기체의 $h$와 $s$는 이상기체보다 작다. 그래서 $(\bar h^* - \bar h)/\bar R T_c$와 $(\bar s^* - \bar s)/\bar R$는 양수이다.Sign of the departure: at the same $T$ and $p$, $h$ and $s$ of the real gas are smaller than those of the ideal gas, so $(\bar h^* - \bar h)/\bar R T_c$ and $(\bar s^* - \bar s)/\bar R$ are positive.
적용 범위: 대응 상태 원리에 바탕을 두므로 극성이 작은 기체에서 정확하고, 극성이 크거나 양자 효과가 있는 수소와 헬륨은 유효 임계값을 써야 한다.Range of validity: based on corresponding states, the charts are accurate for weakly polar gases; hydrogen and helium need effective critical constants because of quantum effects.
Figure 11.7엔탈피 편차, 엔트로피 편차, $Z$, fugacity 계수Enthalpy and Entropy Departures, $Z$ and Fugacity Coefficient
환산 온도 $T_R$Reduced temperature $T_R$1.30
환산 압력 $p_R$Reduced pressure $p_R$3.0
$Z$$Z$—
$(\bar h^*-\bar h)/\bar R T_c$$(\bar h^*-\bar h)/\bar R T_c$—
Lee-Kesler 단순 유체 식 (Moran의 일반화 선도 A-4, A-5와 같은 대응 상태 자료)을 풀어 그렸다. 이 식이 해석식이므로 편차와 $\ln\phi = \int_0^p (Z-1)/p\,dp$를 같은 $Z$ 곡선에서 구했고, 수치 적분과 맞는지 확인했다. 압력이 높아질수록 편차가 커지고, 같은 $p_R$에서 $T_R$가 낮을수록 편차가 크다. $\phi<1$이면 실제 기체의 화학 퍼텐셜이 이상기체보다 낮다.Plotted from the Lee-Kesler simple-fluid equation, the same corresponding-states data as Moran's generalized charts A-4 and A-5. Because the equation is closed-form, the departures and $\ln\phi = \int_0^p (Z-1)/p\,dp$ follow from one $Z$ surface, and the departures were checked against numerical integration. Departures grow with pressure and are larger at lower $T_R$ for the same $p_R$. $\phi<1$ means the real gas has a lower chemical potential than the ideal gas.
Section 11.8
기체 혼합물의 $p$-$v$-$T$ 관계$p$-$v$-$T$ Relations for Gas Mixtures
혼합물의 $p$-$v$-$T$ 관계는 순수 물질의 상태방정식에 혼합 규칙을 넣어 구한다. 상태방정식의 상수를 몰분율로 평균하거나, 혼합물을 가상의 순수 물질로 보고 일반화 선도를 쓰거나, 성분별 기여를 더한다. 어느 방법도 혼합 시 성분 사이 상호작용을 근사하므로 결과가 다르다.The $p$-$v$-$T$ relation of a mixture is built from pure-substance equations of state plus mixing rules. One can average the equation-of-state constants by mole fraction, treat the mixture as a hypothetical pure substance and use the generalized chart, or add component contributions. Each method approximates the interactions among components differently, so results differ.
Kay 규칙: 몰분율 가중 평균으로 유사 임계 온도와 압력을 정하고 일반화 선도에서 $Z$를 읽는다. 계산이 가장 간단하며, 성분의 임계값이 크게 다르지 않을 때 쓴다.Kay's rule: pseudocritical temperature and pressure come from mole-fraction averages, and $Z$ is read from the generalized chart. It is the simplest method and is used when the components' critical values are not very different.
분압 가산 규칙: 성분 $i$가 혼합물의 온도와 부피를 혼자 차지할 때의 압력을 구해 합한다.Additive pressure rule: the pressure each component would exert alone at the mixture temperature and volume are summed.
분체적 가산 규칙: 성분 $i$가 혼합물의 온도와 압력에서 차지하는 부피를 구해 합한다. 이상기체에서는 분압 가산 규칙과 같은 결과가 된다.Additive volume rule: the volume each component would occupy at the mixture temperature and pressure are summed. For ideal gases it gives the same result as the additive pressure rule.
Section 11.9
다성분계 해석과 fugacityAnalyzing Multicomponent Systems and Fugacity
조성이 변하는 계에서는 상태량이 $T$, $p$ 외에 각 성분의 몰수에도 의존한다. 성분 $i$의 부분 몰 상태량 $\bar X_i = (\partial X/\partial n_i)_{T,p,n_j}$로 혼합물의 상태량 $X = \sum n_i \bar X_i$를 나타내며, Gibbs 함수의 부분 몰 값이 화학 퍼텐셜 $\mu_i$이다. 상평형은 성분마다 각 상의 화학 퍼텐셜이 같을 때 이루어진다.In a system of variable composition, properties depend on the mole numbers of each component as well as $T$ and $p$. The partial molal property $\bar X_i = (\partial X/\partial n_i)_{T,p,n_j}$ expresses the mixture property as $X = \sum n_i \bar X_i$, and the partial molal Gibbs function is the chemical potential $\mu_i$. Phase equilibrium holds when each component has equal chemical potential in every phase.
화학 퍼텐셜은 이상기체 기준에서 로그 형태로 쓸 수 있도록 fugacity $f$를 정의한다. 압력이 0에 가까워지면 $f/p \to 1$이다. 순수 성분에서 $\ln(f/p)$는 $Z$ 선도의 면적으로 얻는다. 이상 용액을 가정한 Lewis-Randall 규칙은 혼합물 안 성분의 fugacity를 순수 성분 fugacity에 몰분율을 곱해 구한다. Figure 11.7의 $\phi$ 값이 이 계수이며, $\phi<1$이면 인력이 우세하다.Fugacity $f$ is defined so that the chemical potential keeps the logarithmic form of the ideal-gas reference; $f/p \to 1$ as $p \to 0$. For a pure component $\ln(f/p)$ is obtained from the area under the $Z$ chart. The Lewis-Randall rule, which assumes an ideal solution, sets the fugacity of a component in the mixture to the pure-component fugacity times its mole fraction. The $\phi$ in Figure 11.7 is this coefficient; $\phi<1$ means attraction dominates.
부분 몰 상태량: 혼합물에 성분 $i$를 조금 더할 때 상태량이 늘어나는 비율이다. 부분 몰 부피는 순수 성분의 몰 부피와 다를 수 있다.Partial molal property: the rate at which a property grows when a little of component $i$ is added to the mixture. The partial molal volume can differ from the molar volume of the pure component.
Gibbs-Duhem 식: $T$와 $p$가 일정할 때 $\sum n_i\,d\mu_i = 0$이므로 성분들의 화학 퍼텐셜은 서로 독립이 아니다.Gibbs-Duhem equation: at constant $T$ and $p$, $\sum n_i\,d\mu_i = 0$, so the chemical potentials of the components are not independent.
Self-Check
확인 문제Quiz
Q1. van der Waals 식이 모든 물질에 대해 예측하는 임계 압축성 인자 $Z_c$는 얼마인가?Q1. What critical compressibility factor $Z_c$ does the van der Waals equation predict for every substance?
$a = 27R^2T_c^2/(64p_c)$, $b = RT_c/(8p_c)$, $v_c = 3b$를 $Z_c = p_cv_c/(RT_c)$에 넣으면 $3/8 = 0.375$이다. 실제 물질의 값은 약 0.27 근처이므로 van der Waals 식은 임계점 근처의 체적을 크게 예측한다.Putting $a = 27R^2T_c^2/(64p_c)$, $b = RT_c/(8p_c)$ and $v_c = 3b$ into $Z_c = p_cv_c/(RT_c)$ gives $3/8 = 0.375$. Real substances sit near 0.27, so the equation overestimates volume near the critical point.
Q2. 100 °C의 포화수에서 $h_{fg}$ = 2257 kJ/kg, $v_{fg}$ = 1.672 m3/kg이다. 증기압 곡선의 기울기 $dp/dT$는 얼마인가?Q2. For saturated water at 100 °C, $h_{fg}$ = 2257 kJ/kg and $v_{fg}$ = 1.672 m3/kg. What is the slope $dp/dT$ of the vapor-pressure curve?
$dp/dT = h_{fg}/(T v_{fg}) = 2257/(373.15 \times 1.672) = 3.62$ kPa/K이다. 온도가 1 K 올라가면 포화 압력이 약 3.6 kPa 올라간다.$dp/dT = h_{fg}/(T v_{fg}) = 2257/(373.15 \times 1.672) = 3.62$ kPa/K. Each 1 K rise raises the saturation pressure by about 3.6 kPa.
Q3. N2 50 몰%와 CO2 50 몰% 혼합물에 Kay 규칙을 쓸 때 유사 임계 온도와 압력은? (N2: 126.2 K, 33.9 bar. CO2: 304.2 K, 73.9 bar)Q3. Using Kay's rule for a 50 mol% N2 and 50 mol% CO2 mixture, what are the pseudocritical temperature and pressure? (N2: 126.2 K, 33.9 bar. CO2: 304.2 K, 73.9 bar)
$T_c' = 0.5(126.2) + 0.5(304.2) = 215.2$ K, $p_c' = 0.5(33.9) + 0.5(73.9) = 53.9$ bar이다. 온도와 압력 모두 몰분율 가중 산술 평균이다.$T_c' = 0.5(126.2) + 0.5(304.2) = 215.2$ K and $p_c' = 0.5(33.9) + 0.5(73.9) = 53.9$ bar. Both are mole-fraction weighted arithmetic means.
What If?
만약에?What If?
van der Waals 식에서 $a = 0$으로 두면?What if $a = 0$ in the van der Waals equation?
클릭하여 확인 →Click to reveal →
인력 항이 없어지므로 $p = RT/(v-b)$만 남고 모든 등온선이 $v$에 대해 단조 감소한다. 임계점($T_c \propto a$)과 액화가 사라져서, 어떤 온도에서도 기체가 응축하지 않는다. 또한 $T(\partial p/\partial T)_v = p$가 되어 $(\partial u/\partial v)_T = a/v^2$이 0이 되고, $u$는 온도만의 함수가 된다.Without the attraction term only $p = RT/(v-b)$ remains and every isotherm decreases monotonically in $v$. The critical point ($T_c \propto a$) and condensation disappear, so the gas never liquefies. Also $(\partial u/\partial v)_T = a/v^2$ becomes 0, so $u$ depends on temperature alone.
임계점에 가까워지면 Clapeyron 방정식의 $h_{fg}$와 $v_{fg}$는?What happens to $h_{fg}$ and $v_{fg}$ in the Clapeyron equation near the critical point?
클릭하여 확인 →Click to reveal →
둘 다 0으로 간다. 포화 액체와 증기의 구별이 사라지기 때문이다. 그러나 두 값의 비 $h_{fg}/(T v_{fg})$는 0이 되지 않고 유한한 값(물의 360 °C 부근에서 약 225 kPa/K)을 가진다. 증기압 곡선은 임계점에서 끝나지만 기울기는 유한하다.Both go to zero because liquid and vapor become indistinguishable. Their ratio $h_{fg}/(T v_{fg})$ does not vanish but stays finite and large (about 225 kPa/K for water at 360 °C). The vapor-pressure curve ends at the critical point with a finite slope.
수소를 실온에서 교축하면 온도는 어떻게 되는가?What happens to hydrogen throttled at room temperature?
클릭하여 확인 →Click to reveal →
온도가 올라간다. 수소의 임계 온도는 약 33 K이므로 실온(약 300 K)은 $T_R \approx 9$이고, 이는 영압력 상한 역전 온도 6.75 $T_c$보다 높은 영역에 있다. 수소를 교축으로 액화하려면 먼저 약 200 K 아래로 예냉하여 역전 곡선 안쪽에 들어가야 한다.The temperature rises. The critical temperature of hydrogen is about 33 K, so room temperature (about 300 K) is $T_R \approx 9$, above the zero-pressure upper inversion value of 6.75 $T_c$. To liquefy hydrogen by throttling, it must first be precooled to the inversion curve's interior, below roughly 200 K.
Key Takeaways
01
상태방정식과 대응 상태Equations of State and Corresponding States
두 상수 식은 임계점에서 $a$, $b$를 정한다. $T_R$와 $p_R$가 같으면 $Z$가 비슷하므로 일반화 선도 하나로 여러 기체를 다룬다.Two-constant equations fix $a$ and $b$ at the critical point. Gases at equal $T_R$ and $p_R$ have similar $Z$, so one generalized chart serves many gases.
02
완전 미분에서 나온 관계식Relations from Exact Differentials
Maxwell 관계식은 엔트로피 편미분을 $p$-$v$-$T$ 편미분으로 바꾼다. $g_f = g_g$에서 Maxwell 등면적 구성과 Clapeyron 방정식이 나온다.Maxwell relations replace entropy derivatives with $p$-$v$-$T$ derivatives. From $g_f = g_g$ come the Maxwell equal-area construction and the Clapeyron equation.
03
$du$, $dh$, $ds$와 비열, 교축$du$, $dh$, $ds$, Specific Heats and Throttling
$p$-$v$-$T$ 식과 $c_p^*(T)$로 $\Delta u$, $\Delta h$, $\Delta s$를 구한다. $c_p - c_v = vT\beta^2/\kappa$이고, $\mu_J$의 부호가 교축 시 온도가 오르내리는 방향을 정한다.A $p$-$v$-$T$ equation and $c_p^*(T)$ give $\Delta u$, $\Delta h$ and $\Delta s$. $c_p - c_v = vT\beta^2/\kappa$, and the sign of $\mu_J$ sets whether throttling heats or cools.
04
편차, 혼합물, fugacityDepartures, Mixtures and Fugacity
편차 선도는 이상기체 값에 실제 기체 보정을 더한다. 혼합물은 Kay 규칙 등으로 유사 임계값을 정하고, 다성분 평형은 fugacity로 다룬다.Departure charts add a real-gas correction to ideal-gas values. Mixtures use pseudocritical values such as Kay's rule, and multicomponent equilibrium is handled with fugacity.