등온 반응기 설계: 몰 수와 몰 유량Isothermal Reactor Design: Moles and Molar Flow Rates
Fogler, Elements of Chemical Reaction Engineering, Chapter 6. 그림을 끌어 움직이면 몰 유량과 농도가 실시간으로 바뀐다.Fogler, Elements of Chemical Reaction Engineering, Chapter 6. Drag the figures and watch molar flow rates and concentrations respond in real time.
몰 유량 알고리즘상대 속도마이크로반응기막 반응기CSTR 시동반회분식 반응기반응 증류
Section 6.1
몰 유량 수지 알고리즘The Molar Flow Rate Balance Algorithm
5장에서는 전환율 하나로 반응기를 설계했다. 한 화학종에만 몰 수지를 쓰면 되기 때문이다. 그러나 막 반응기, 기상에서 일어나는 다중 반응, 비정상 상태 반응기에서는 전환율 하나로 조성을 나타낼 수 없다. 이런 경우에는 몰 수($N_j$) 또는 몰 유량($F_j$)을 종속 변수로 쓴다. 액상 반응에는 농도 $C_j$를, 기상 반응에는 몰 유량 $F_j$를 주로 쓴다.Chapter 5 designed reactors with a single variable, conversion, because one mole balance on one species was enough. Membrane reactors, multiple gas-phase reactions, and unsteady-state reactors cannot be described by conversion alone. Then the number of moles ($N_j$) or the molar flow rate ($F_j$) becomes the dependent variable: concentration $C_j$ is used for liquids and $F_j$ for gases.
전환율 방식과 다른 점은 하나이다. 전환율 방식은 한 화학종에 몰 수지를 쓰지만, 몰 유량 방식은 존재하는 모든 화학종 각각에 몰 수지를 쓴다. 그다음 속도식을 쓰고, 상대 속도로 각 화학종의 반응 속도를 서로 연결한다. 농도를 몰 유량으로 나타낸 뒤에는 ODE solver(Polymath, MATLAB)가 결합 단계를 대신 수행한다.Only one thing differs from the conversion method. The conversion method writes a mole balance on one species; the molar flow rate method writes one on every species present. Then comes the rate law, and relative rates tie the species' reaction rates together. Once concentrations are expressed through molar flow rates, an ODE solver (Polymath, MATLAB) performs the combine step.
알고리즘 여섯 단계: (1) 모든 화학종에 몰 수지를 쓴다. (2) 속도식을 쓴다. (3) 상대 속도로 $r_j$를 서로 연결한다. (4) 화학량론으로 $C_j$를 $F_j$로 나타낸다. (5) 기상이면 압력 강하식을 쓴다. (6) ODE solver로 결합하여 푼다.Six steps: (1) mole balance on every species, (2) rate law, (3) relative rates linking each $r_j$, (4) stoichiometry giving $C_j$ from $F_j$, (5) pressure-drop equation for gases, (6) combine and solve with an ODE solver.
몰 유량 방식이 필요한 경우: 막 반응기, 기상 다중 반응, 비정상 상태의 CSTR와 반회분식 반응기이다. 이 장의 예제 세 개(마이크로반응기, 막 반응기, 반회분식 반응기)가 각각 이 경우에 해당한다.When it is needed: membrane reactors, multiple gas-phase reactions, and unsteady CSTRs and semibatch reactors. The three examples of this chapter (microreactor, membrane reactor, semibatch reactor) each represent one case.
Section 6.2
CSTR, PFR, PBR, 회분식 반응기의 몰 수지Mole Balances on CSTRs, PFRs, PBRs, and Batch Reactors
액상 반응에서는 밀도가 일정하므로 반응이 진행되어도 부피 $V$와 부피 유량 $v$가 변하지 않는다. 그래서 농도가 설계 변수로 편하다. 일반 반응 $a\mathrm{A}+b\mathrm{B}\rightarrow c\mathrm{C}+d\mathrm{D}$에 대해 네 가지 반응기의 몰 수지를 각 화학종마다 쓰고, 상대 속도로 연결하면 아래 식이 된다. 회분식, PFR, PBR은 연립 상미분방정식이고, CSTR는 연립 대수 방정식이다.In liquid-phase reactions the density is constant, so neither the volume $V$ nor the volumetric flow rate $v$ changes with reaction, and concentration is the convenient design variable. Writing the balance of each species for the four reactor types and linking them by relative rates gives the equations below. Batch, PFR, and PBR give coupled ODEs; the CSTR gives coupled algebraic equations.
기상 반응에서는 몰 수가 변하면 부피 유량이 변한다. 그래서 몰 유량 $F_j$를 종속 변수로 두고, 농도는 총 몰 유량 $F_T$와의 비로 나타낸다. 등온 운전($T=T_0$)에서 PBR의 압력은 $p=P/P_0$에 대한 식으로 함께 푼다.In gas-phase reactions a change in the number of moles changes the volumetric flow rate. Therefore $F_j$ is the dependent variable and each concentration is written through the ratio to the total molar flow rate $F_T$. For isothermal operation ($T=T_0$) the PBR pressure $p=P/P_0$ is solved together.
상대 속도: 한 화학종의 속도식 하나만 정하면 나머지 화학종의 $r_j$는 화학량론 계수의 비로 결정된다. 예를 들어 $\mathrm{A}+2\mathrm{B}\rightarrow\mathrm{C}$에서 $r_B=2r_A$, $r_C=-r_A$이다.Relative rates: once one species' rate law is fixed, every other $r_j$ follows from the ratio of stoichiometric coefficients. For $\mathrm{A}+2\mathrm{B}\rightarrow\mathrm{C}$, $r_B=2r_A$ and $r_C=-r_A$.
총 몰 유량 $F_T$: 모든 화학종과 비활성 성분의 몰 유량 합이다. 기상에서는 $F_T$가 위치에 따라 변하므로 농도식에 반드시 들어간다.Total molar flow rate $F_T$: the sum of all reacting species and inerts. In gases $F_T$ changes along the reactor, so it must appear in every concentration expression.
Figure 6.1PFR에서 A + 2B → C의 위치별 몰 유량과 상대 속도Molar Flow Rates and Relative Rates Along a PFR for A + 2B → C
예측: 액상 PFR에서 A가 1 mol/s 소비되는 동안 B는 몇 mol/s 소비될까?Predict: while 1 mol/s of A is consumed in a liquid-phase PFR, how many mol/s of B are consumed?
목표: 그림을 좌우로 끌어 $F_C=F_A$가 되는 부피(전환율 0.5)를 전환율 오차 0.03 이내로 찾으세요. 속도 상수 $k$를 바꾸면 답도 바뀝니다.Goal: drag the figure left and right to find the volume where $F_C=F_A$ (conversion 0.5), within 0.03 in conversion. Changing $k$ moves the answer.
속도 상수 $k$ (dm³/(mol s))Rate constant $k$ (dm³/(mol s))0.5
부피 VVolume V—
F_A—
F_B—
F_C—
전환율 XConversion X—
조건은 $v_0=1$ dm³/s, $F_{A0}=1$ mol/s, $F_{B0}=2$ mol/s, $-r_A=kC_AC_B$이다. 화학량론비로 공급했으므로 $F_B=2F_A$가 모든 위치에서 성립하고, 이것이 상대 속도 $r_B=2r_A$가 나타나는 모습이다. 이때 $X=2kV/(1+2kV)$이다.Conditions: $v_0=1$ dm³/s, $F_{A0}=1$ mol/s, $F_{B0}=2$ mol/s, $-r_A=kC_AC_B$. Fed in stoichiometric ratio, $F_B=2F_A$ holds everywhere, which is the relative rate $r_B=2r_A$ at work. The conversion is $X=2kV/(1+2kV)$.
Section 6.3
마이크로반응기에 적용한 PFR 몰 유량 알고리즘Application of the PFR Molar Flow Rate Algorithm to a Microreactor
마이크로반응기는 폭 100 µm, 길이 2 cm 정도의 채널을 가진 반응기이다. 부피 대비 표면적이 약 10,000 m²/m³로 커서 열 전달과 물질 전달 저항이 거의 없고, 발열이 큰 반응도 거의 등온으로 운전할 수 있다. 그래서 본래의 반응 속도론을 연구하는 데 쓰인다. 독성 또는 폭발성 중간체를 만들 때에도 장치 하나에 담긴 양이 적어 누출이나 폭발의 피해가 작다. 생산량은 병렬로 장치를 더해서 늘린다.A microreactor has channels about 100 µm wide and 2 cm long. The surface-to-volume ratio of about 10,000 m²/m³ removes most heat and mass transfer resistance, and even strongly exothermic reactions can run nearly isothermally. This makes microreactors suitable for studying intrinsic kinetics. For toxic or explosive intermediates, the small inventory limits the damage of a leak or microexplosion. Production is scaled up by adding units in parallel.
예제 6-1은 순수 NOCl을 425°C, 1641 kPa에서 반응시키는 $2\mathrm{NOCl}\rightarrow2\mathrm{NO}+\mathrm{Cl_2}$이다. 속도식은 기초 반응이므로 $-r_A=kC_A^2$이고, $k=0.29$ dm³/(mol s)(500 K)와 활성화 에너지 24 kcal/mol이 주어진다. 연간 NO 20톤을 85% 전환율로 만들려면 채널 하나에 NOCl을 $2.26\times10^{-5}$ mol/s 공급해야 한다. 채널 하나의 부피는 $10^{-5}$ dm³이다.Example 6-1 is $2\mathrm{NOCl}\rightarrow2\mathrm{NO}+\mathrm{Cl_2}$ with pure NOCl at 425°C and 1641 kPa. The rate law is elementary, $-r_A=kC_A^2$, with $k=0.29$ dm³/(mol s) at 500 K and $E=24$ kcal/mol. Producing 20 tons of NO per year at 85% conversion needs $2.26\times10^{-5}$ mol/s of NOCl per channel. One channel has a volume of $10^{-5}$ dm³.
NOCl을 A, NO를 B, Cl₂를 C라 하면 반응은 $\mathrm{A}\rightarrow\mathrm{B}+\tfrac{1}{2}\mathrm{C}$이다. 세 화학종에 몰 수지를 쓰고, 상대 속도 $r_B=-r_A$, $r_C=-r_A/2$로 연결한다. 몰 수가 늘어나는 반응이므로 $F_T=F_A+F_B+F_C$가 위치에 따라 커지고, 이 값이 농도에 들어간다.Calling NOCl A, NO B, and Cl₂ C, the reaction is $\mathrm{A}\rightarrow\mathrm{B}+\tfrac{1}{2}\mathrm{C}$. Mole balances are written on all three species and linked by $r_B=-r_A$ and $r_C=-r_A/2$. The number of moles increases, so $F_T=F_A+F_B+F_C$ grows along the channel and enters every concentration.
전환율로도 풀 수 있는 문제: 이 예제는 전환율로도 풀린다. 몰 유량 방식을 연습하는 이유는 막 반응기와 다중 반응처럼 전환율로 풀 수 없는 문제를 준비하기 위해서이다.Solvable by conversion too: this example could be solved with conversion. The molar flow rate method is practiced here to prepare for membrane reactors and multiple reactions, where conversion is not enough.
입구 근처에서 빠른 변화: 반응물 농도가 가장 높은 입구에서 속도가 크므로 몰 유량이 입구 근처에서 급하게 변하고 이후에는 거의 변하지 않는다.Fast change near the inlet: the rate is highest where the reactant concentration is highest, so the flow rates change quickly near the inlet and then level off.
Figure 6.2마이크로반응기 채널의 온도, 압력에 따른 몰 유량 분포Molar Flow Rate Profiles in a Microreactor Channel vs Temperature and Pressure
온도 $T$ (°C)Temperature $T$ (°C)425
압력 $P_0$ (kPa)Pressure $P_0$ (kPa)1641
k (dm3/mol/s)—
C_T0 (mol/dm3)—
X = 0.85 부피 (µL)Volume at X = 0.85 (µL)—
채널 부피 대비Relative to channel—
조건은 예제 6-1의 값($k=0.29$ dm³/(mol s) at 500 K, $E=24$ kcal/mol, 채널당 $F_{A0}=22.6$ µmol/s)이고, 이상 기체, 압력 강하 없음, $-r_A=kC_A^2$로 이 페이지에서 직접 수치 적분했다. 압력을 올리면 $C_{T0}$가 커져 속도가 $C_{T0}^2$에 비례해 빨라지므로 85% 전환율에 필요한 부피가 크게 줄어든다.Data from Example 6-1 ($k=0.29$ dm³/(mol s) at 500 K, $E=24$ kcal/mol, $F_{A0}=22.6$ µmol/s per channel), ideal gas, no pressure drop, $-r_A=kC_A^2$, integrated numerically in this page. Raising pressure raises $C_{T0}$, and the rate scales with $C_{T0}^2$, so the volume needed for 85% conversion drops sharply.
Section 6.4
막 반응기Membrane Reactors
열역학적으로 제한된 반응은 평형이 반응물 쪽에 있어서 전환율이 작다. 발열 반응에서는 온도를 올리면 평형이 더 왼쪽으로 가고, 온도를 내리면 속도가 너무 느리다. 흡열 반응은 온도를 올리면 되지만 촉매가 비활성화되는 경우가 많다. 막 반응기는 생성물 하나를 반투과막으로 계속 빼내어 역반응이 일어나지 못하게 하고, 같은 원리로 반응 증류도 쓰인다.A thermodynamically limited reaction has its equilibrium on the reactant side and little conversion. For an exothermic reaction, raising the temperature shifts equilibrium further left and lowering it makes the rate too slow. An endothermic reaction can be heated, but the catalyst often deactivates. A membrane reactor continuously removes one product through a semipermeable membrane so the reverse reaction cannot occur; reactive distillation works on the same principle.
대표적인 형태는 촉매 입자를 공급 쪽에 넣은 불활성 막 반응기(IMRCF)와 막 자체에 촉매를 입힌 촉매 막 반응기(CMR)이다. 예를 들어 $\mathrm{C_6H_{12}}\rightleftharpoons3\mathrm{H_2}+\mathrm{C_6H_6}$에서 작은 H₂ 분자만 막의 기공을 통과하므로, 평형 상수가 작아도 반응은 오른쪽으로 계속 진행한다. 에틸벤젠의 스티렌 탈수소, 프로판과 부탄의 탈수소도 같은 형태 $\mathrm{A}\rightleftharpoons\mathrm{B}+\mathrm{C}$로 나타낸다.Typical designs are the inert membrane reactor with catalyst on the feed side (IMRCF) and the catalytic membrane reactor (CMR) with catalyst on the membrane itself. For $\mathrm{C_6H_{12}}\rightleftharpoons3\mathrm{H_2}+\mathrm{C_6H_6}$, only the small H₂ molecule passes through the pores, so the reaction continues to the right even when the equilibrium constant is small. Dehydrogenation of ethylbenzene to styrene, propane, and butane has the same form $\mathrm{A}\rightleftharpoons\mathrm{B}+\mathrm{C}$.
막을 통과하는 B(H₂)는 반응기 옆면과 끝으로 나간다. 그래서 B의 몰 수지에는 유출 항 $R_B$가 하나 더 들어간다. 이 때문에 막 반응기는 몰 유량으로 풀어야 한다. B의 몰 유량을 전환율로 나타내면 옆면으로 빠져나간 양을 반영하지 못한다. $R_B$는 막의 물질 전달 계수 $k_C'$와 단위 부피당 막 면적 $a=4/D$의 곱 $k_C=k_C'a$로 쓰고, 소기 기체(sweep gas) 쪽 농도를 0으로 놓았다.B (H₂) passing through the membrane leaves through the sides as well as the end of the reactor, so the mole balance on B has an extra loss term $R_B$. This is why membrane reactors must be solved with molar flow rates: expressing $F_B$ through conversion cannot account for what left through the walls. $R_B$ is written with $k_C=k_C'a$, the product of the membrane mass transfer coefficient $k_C'$ and the membrane area per volume $a=4/D$, with the sweep-gas concentration taken as zero.
예제 6-2의 값: $k=0.7$ min⁻¹, $K_C=0.05$ mol/dm³, $k_C=0.2$ min⁻¹, $C_{T0}=0.2$ mol/dm³, $F_{A0}=10$ mol/min이다. $V=500$ dm³에서 $F_A=4$ mol/min이므로 $X=0.60$이다. 막이 없는 PFR의 평형 전환율은 $X_e=0.447$이다.Values of Example 6-2: $k=0.7$ min⁻¹, $K_C=0.05$ mol/dm³, $k_C=0.2$ min⁻¹, $C_{T0}=0.2$ mol/dm³, $F_{A0}=10$ mol/min. At $V=500$ dm³, $F_A=4$ mol/min, so $X=0.60$. A PFR without membrane is limited to $X_e=0.447$.
$F_B$의 극대: A에서 B가 생기는 속도와 막으로 B가 빠지는 속도가 경쟁하므로 $F_B$는 극댓값을 지난다. B를 빨리 빼면 $F_B$가 0에 가까워져 반응이 비가역처럼 진행되고, 느리게 빼면 $F_B$가 커서 $-r_A$가 작아진다.Maximum of $F_B$: B formation from A competes with B removal through the wall, so $F_B$ passes a maximum. Fast removal brings $F_B$ near zero and the reaction behaves irreversibly; slow removal keeps $F_B$ high and $-r_A$ small.
막으로 공급하는 경우: 반응물 B를 막 옆면에서 고르게 넣으면 $dF_B/dV=r_B+R_B$, $R_B=F_{B0}/V_t$이다. A 농도는 높게, B 농도는 낮게 유지하여 8장의 선택도를 높인다. 공급 속도는 막 양쪽의 압력 차로 조절한다.Feeding through the membrane: feeding B uniformly along the wall gives $dF_B/dV=r_B+R_B$ with $R_B=F_{B0}/V_t$. This keeps $C_A$ high and $C_B$ low and improves the selectivity treated in Chapter 8. The feed rate is controlled by the pressure difference across the membrane.
Figure 6.3막을 통한 H₂ 투과와 평형 전환율 초과H₂ Permeation Through the Wall and Conversion Beyond Equilibrium
예측: 막 투과 계수 $k_C$를 0에서 올리면 V = 500 dm³에서의 전환율은 평형 전환율 $X_e$보다 어떻게 될까?Predict: as the membrane coefficient $k_C$ rises from zero, how does the conversion at V = 500 dm³ compare with the equilibrium conversion $X_e$?
목표: 아래쪽 막대의 점을 끌어 $k_C$를 바꾸고 전환율 80% 이상을 달성하세요. $K_C$ 버튼을 바꾸면 필요한 $k_C$도 달라집니다.Goal: drag the dot on the lower bar to change $k_C$ and reach at least 80% conversion. Changing the $K_C$ button changes the required $k_C$.
k_C (1/min)—
전환율 XConversion X—
평형 전환율 X_eEquilibrium X_e—
투과한 H2 (mol/min)H2 permeated (mol/min)—
조건은 예제 6-2($k=0.7$ min⁻¹, $C_{T0}=0.2$ mol/dm³, $F_{A0}=10$ mol/min, $V=500$ dm³)이다. $k_C=0$이면 전환율이 $X_e$에서 멈추지만, H₂가 빠져나가면 $-r_A=k(C_A-C_BC_C/K_C)$의 역반응 항이 줄어 전환율이 $X_e$를 넘는다. $k_C$를 지나치게 키우면 $F_B$가 0에 가까워져 비가역 반응처럼 진행되고, 이후에는 전환율이 거의 늘지 않는다.Conditions of Example 6-2 ($k=0.7$ min⁻¹, $C_{T0}=0.2$ mol/dm³, $F_{A0}=10$ mol/min, $V=500$ dm³). At $k_C=0$ the conversion stops at $X_e$; when H₂ leaves, the reverse term of $-r_A=k(C_A-C_BC_C/K_C)$ shrinks and the conversion passes $X_e$. A very large $k_C$ drives $F_B$ toward zero, the reaction behaves as irreversible, and the conversion gains little further.
Figure 6.4막 반응기와 일반 PFR의 전환율 곡선 비교Conversion Curves of a Membrane Reactor and a Conventional PFR
조건은 예제 6-2($k=0.7$ min⁻¹, $C_{T0}=0.2$ mol/dm³, $F_{A0}=10$ mol/min)이고 4차 Runge-Kutta로 직접 적분했다. $K_C$가 작을수록 일반 PFR의 $X_e$가 낮아서 막 반응기의 이득이 크다. $K_C$가 크면 평형이 이미 오른쪽이라 막의 이득이 작아진다.Conditions of Example 6-2 ($k=0.7$ min⁻¹, $C_{T0}=0.2$ mol/dm³, $F_{A0}=10$ mol/min), integrated here by fourth-order Runge-Kutta. The smaller $K_C$ is, the lower the $X_e$ of a conventional PFR and the larger the membrane gain. For large $K_C$ equilibrium already lies to the right and the gain is small.
Section 6.5
교반 반응기의 비정상 상태 운전Unsteady-State Operation of Stirred Reactors
회분식 반응기는 5장에서 다뤘다. 이 절은 교반 반응기의 비정상 상태 운전 두 가지, CSTR의 시동과 반회분식 반응기를 다룬다. 두 경우 모두 농도와 전환율을 시간의 함수로 예측하는 것이 목적이다. 닫힌 형태의 해는 0차와 1차 반응에서만 얻어지고, 다른 차수에서는 ODE solver를 써야 한다.The batch reactor was covered in Chapter 5. This section treats two other unsteady operations of stirred reactors: startup of a CSTR and semibatch reactors. In both we want concentration and conversion as functions of time. Closed-form solutions exist only for zero- and first-order reactions; other orders need an ODE solver.
CSTR를 시동할 때 탱크에는 처음에 반응물이 없고, 입구에서 농도 $C_{A0}$의 공급이 시작된다. 1차 반응의 몰 수지는 $dC_A/dt=(C_{A0}-C_A)/\tau-kC_A$이고, 해는 지수 함수로 정상 상태에 접근한다. 접근 속도는 $1/\tau+k$로 정해지므로 정상 값의 99%에 이르는 시간은 $t_s\approx4.6/(k+1/\tau)$이다. 대부분의 1차 계에서 정상 상태까지 공간 시간 3배에서 4배가 걸린다.When a CSTR is started, the tank initially holds no reactant and a feed of concentration $C_{A0}$ begins at the inlet. The first-order mole balance is $dC_A/dt=(C_{A0}-C_A)/\tau-kC_A$, and the solution approaches steady state exponentially. The approach rate is $1/\tau+k$, so the time to reach 99% of the steady value is $t_s\approx4.6/(k+1/\tau)$. For most first-order systems steady state takes 3 to 4 space times.
반응 증류: 두 번째 유형의 반회분식 반응기이다. 반응물 A와 B를 한꺼번에 넣고 생성물 하나를 증발시켜 계속 빼낸다. 평형이 오른쪽으로 이동하여 최종 전환율이 커지고, 반응물이 농축되어 속도가 늘어 처리 시간도 줄어든다. 물을 제거하는 아세틸화와 에스터화 반응에 쓰인다.Reactive distillation: the second type of semibatch reactor. A and B are charged together and one product is vaporized and withdrawn continuously. Equilibrium shifts to the right, so the final conversion rises; the reactants also become more concentrated, which raises the rate and shortens the processing time. It is used for acetylation and esterification, where water is removed.
세 가지 형태: 그림 6-4는 (a) CSTR 시동, (b) 냉각을 갖춘 반회분식 반응기, (c) 반응 증류를 나타낸다. 이 절의 그림 6.5는 (a)를 다루고, 6.6절의 그림 6.6은 (b)를 다룬다.Three forms: Figure 6-4 shows (a) CSTR startup, (b) semibatch with cooling, and (c) reactive distillation. Figure 6.5 below treats (a); Figure 6.6 in Section 6.6 treats (b).
Figure 6.5CSTR 시동 과정의 농도 변화와 정상 상태 도달 시간Concentration Rise and Time to Steady State During CSTR Startup
예측: 공간 시간 $\tau$를 두 배로 늘리면 정상 상태의 99%에 이르는 시간 $t_s$는 어떻게 될까?Predict: if the space time $\tau$ is doubled, what happens to the time $t_s$ to reach 99% of steady state?
목표: 아래 막대의 점을 끌어 $\tau$를 바꾸고, 정상 상태 전환율 80% 이상과 $t_s$ 10분 이하를 동시에 만족시키세요. 반응 속도 상수는 $k=0.4$ min⁻¹입니다.Goal: drag the dot on the bar below to change $\tau$ and satisfy steady-state conversion of at least 80% and $t_s$ of at most 10 min together. The rate constant is $k=0.4$ min⁻¹.
공간 시간 τ (min)Space time τ (min)—
정상 C_A / C_A0Steady C_A / C_A0—
정상 전환율 XSteady conversion X—
99%까지 시간 t_s (min)Time to 99% t_s (min)—
$\tau$가 커지면 전환율 $k\tau/(1+k\tau)$는 올라가지만, 시동 시간 $t_s=4.6/(k+1/\tau)$도 함께 길어진다. $t_s$는 $\tau$에 비례하지 않고 $4.6/k$ 쪽으로 포화하므로, 전환율과 시동 시간은 서로 반대로 움직이는 두 목표이다.A larger $\tau$ raises the conversion $k\tau/(1+k\tau)$ but also lengthens the startup time $t_s=4.6/(k+1/\tau)$. Because $t_s$ saturates toward $4.6/k$ instead of growing in proportion to $\tau$, conversion and startup time are two goals that pull in opposite directions.
Section 6.6
반회분식 반응기Semibatch Reactors
반회분식 반응기를 쓰는 가장 큰 이유는 액상 반응의 선택도를 높이는 것이다. 예를 들어 원하는 생성물 D를 만드는 $\mathrm{A}+\mathrm{B}\rightarrow\mathrm{D}$, $r_D=k_DC_A^2C_B$와 원하지 않는 생성물 U를 만드는 $\mathrm{A}+\mathrm{B}\rightarrow\mathrm{U}$, $r_U=k_UC_AC_B^2$가 동시에 일어나는 경우를 생각한다. 순간 선택도 $S_{D/U}=r_D/r_U=(k_D/k_U)(C_A/C_B)$를 크게 하려면 A 농도를 높이고 B 농도를 낮게 유지해야 한다. A만 채운 탱크에 B를 천천히 공급하면 이 조건이 만들어진다.The best reason to use a semibatch reactor is to raise selectivity in liquid-phase reactions. Suppose $\mathrm{A}+\mathrm{B}\rightarrow\mathrm{D}$ with $r_D=k_DC_A^2C_B$ makes the desired product D while $\mathrm{A}+\mathrm{B}\rightarrow\mathrm{U}$ with $r_U=k_UC_AC_B^2$ makes the undesired product U. The instantaneous selectivity $S_{D/U}=r_D/r_U=(k_D/k_U)(C_A/C_B)$ is large only if $C_A$ is kept high and $C_B$ low. Feeding B slowly into a vat of A creates exactly this condition.
몰 공급 속도가 일정한 반회분식 반응기에서는 B가 부피 유량 $v_0$, 농도 $C_{B0}$로 들어오고 유출은 없다. 전체 질량 수지에서 밀도가 일정하면 부피가 $V=V_0+v_0t$로 늘어난다. $N_A=C_AV$를 시간으로 미분하면 부피 증가에 따른 희석 항 $-(v_0/V)C_j$가 모든 화학종의 농도식에 생긴다. B에는 공급 항이 더해진다.In a semibatch reactor with constant feed, B enters at volumetric rate $v_0$ and concentration $C_{B0}$ with no outflow. An overall mass balance at constant density gives $V=V_0+v_0t$. Differentiating $N_A=C_AV$ in time gives a dilution term $-(v_0/V)C_j$ in the concentration equation of every species, and B also receives a feed term.
예제 6-3은 $\mathrm{CNBr}+\mathrm{CH_3NH_2}\rightarrow\mathrm{CH_3Br}+\mathrm{NCNH_2}$이다. $k=2.2$ dm³/(mol s)이고, 처음 5 dm³의 CNBr 수용액(0.05 mol/dm³)에 메틸아민(0.025 mol/dm³)을 0.05 dm³/s로 넣는다. A는 약 250초에 거의 소진되고, C와 D의 농도는 극댓값을 지난 뒤 B가 계속 들어와 희석되면서 줄어든다. 반응이 5분 안에 끝나므로 이 온도에서 반회분식은 알맞지 않고, 관형 반응기 옆면 공급이나 직렬 CSTR를 쓴다.Example 6-3 is $\mathrm{CNBr}+\mathrm{CH_3NH_2}\rightarrow\mathrm{CH_3Br}+\mathrm{NCNH_2}$ with $k=2.2$ dm³/(mol s). Methylamine (0.025 mol/dm³) is fed at 0.05 dm³/s into 5 dm³ of 0.05 mol/dm³ CNBr. A is nearly consumed at about 250 s, and C and D pass a maximum concentration before B keeps diluting them. The reaction is over within 5 minutes, so a semibatch reactor is unsuitable at this temperature; side feeding into a tubular reactor or CSTRs in series would be used.
희석 항: 농도식에서 $-(v_0/V)C_j$는 반응과 관계없이 부피가 늘어서 생기는 감소이다. 이 항 때문에 생성물 C의 농도가 극댓값을 지난다.Dilution term: $-(v_0/V)C_j$ is the decrease caused by volume growth regardless of reaction. It is why the product concentration C passes a maximum.
평형 전환율의 변화: 가역 반응에서는 B를 계속 넣기 때문에 평형이 계속 오른쪽으로 이동한다. 그래서 반회분식 반응기의 평형 전환율 $X_e$는 시간에 따라 변한다.Time-varying equilibrium conversion: for reversible reactions the continued addition of B keeps shifting equilibrium to the right, so the equilibrium conversion $X_e$ of a semibatch reactor changes with time.
Figure 6.6반회분식 반응기의 B 공급 속도와 농도, 부피 변화Feed Rate of B, Concentrations, and Volume in a Semibatch Reactor
예측: B의 공급 속도 $v_0$를 줄이면 A의 전환율이 0.5인 시점의 $C_A/C_B$(선택도 지표)는 어떻게 될까?Predict: if the feed rate $v_0$ of B is reduced, what happens to $C_A/C_B$ (selectivity index) at the moment A is half converted?
목표: 왼쪽 밸브의 점을 위아래로 끌어 $v_0$를 바꾸고, 선택도 지표 $C_A/C_B$ 6 이상과 전환율 0.9 도달 시간 700초 이하를 동시에 만족시키세요. 너무 느리면 시간 조건이, 너무 빠르면 선택도 조건이 맞지 않습니다.Goal: drag the valve dot on the left up and down to change $v_0$ and meet a selectivity index $C_A/C_B$ of at least 6 and a time to 0.9 conversion of at most 700 s together. Too slow fails the time condition; too fast fails the selectivity condition.
v0 (dm3/s)—
X = 0.5에서 C_A/C_BC_A/C_B at X = 0.5—
X = 0.9 도달 시간Time to X = 0.9—
V = 30 dm3 도달 시간Time to V = 30 dm3—
조건은 예제 6-3($k=2.2$ dm³/(mol s), $C_{A0}=0.05$, $C_{B0}=0.025$ mol/dm³, $V_0=5$ dm³)이고, 탱크 부피 30 dm³가 되면 공급을 멈춘다. B를 천천히 넣을수록 B가 들어오는 즉시 소비되어 $C_B$가 낮고 $C_A/C_B$가 크지만, 같은 양의 B를 넣는 데 시간이 오래 걸린다. $v_0$를 바꾸면 선택도와 처리 시간 중 한쪽이 좋아지고 다른 쪽이 나빠진다.Conditions of Example 6-3 ($k=2.2$ dm³/(mol s), $C_{A0}=0.05$, $C_{B0}=0.025$ mol/dm³, $V_0=5$ dm³); the feed stops when the vat reaches 30 dm³. The slower B is added, the sooner it is consumed, so $C_B$ stays low and $C_A/C_B$ high, but adding the same amount takes longer. Selectivity and processing time trade off through $v_0$.
Self-Check
확인 문제Quiz
Q1. $2\mathrm{NOCl}\rightarrow2\mathrm{NO}+\mathrm{Cl_2}$에서 NOCl의 소비 속도가 4 mol/(dm³ s)일 때 Cl₂의 생성 속도는?Q1. In $2\mathrm{NOCl}\rightarrow2\mathrm{NO}+\mathrm{Cl_2}$, what is the formation rate of Cl₂ when NOCl is consumed at 4 mol/(dm³ s)?
상대 속도 $-r_{\mathrm{NOCl}}/2=r_{\mathrm{Cl_2}}/1$에서 $r_{\mathrm{Cl_2}}=4/2=2$ mol/(dm³ s)이다. 계수가 2인 화학종의 속도를 계수 1인 화학종으로 옮길 때 계수 비를 곱해야 한다.From the relative rates $-r_{\mathrm{NOCl}}/2=r_{\mathrm{Cl_2}}/1$, $r_{\mathrm{Cl_2}}=4/2=2$ mol/(dm³ s). Converting between species requires the ratio of stoichiometric coefficients.
Q2. 막 반응기를 전환율 대신 몰 유량으로 풀어야 하는 이유는?Q2. Why must a membrane reactor be solved with molar flow rates instead of conversion?
전환율 방식은 $F_B=F_{A0}(\Theta_B+\nu_BX)$처럼 반응으로 생긴 양만 셈한다. 막으로 빠져나간 양 $R_B$는 반응과 무관한 유출이므로 B의 몰 수지에 $-R_B$ 항을 따로 두고 몰 유량으로 풀어야 한다.The conversion method counts only what reaction produced, as in $F_B=F_{A0}(\Theta_B+\nu_BX)$. The wall loss $R_B$ is an outflow unrelated to reaction, so the balance on B needs a separate $-R_B$ term and must be solved with molar flow rates.
Q3. 1차 반응($k=0.2$ min⁻¹)의 CSTR를 $\tau=5$ min으로 시동한다. 정상 값의 99%에 이르는 시간은?Q3. A first-order reaction ($k=0.2$ min⁻¹) is started in a CSTR with $\tau=5$ min. How long to reach 99% of the steady value?
$t_s=4.6/(k+1/\tau)=4.6/(0.2+0.2)=11.5$ min이다. 반응이 없다면 $4.6\tau=23$ min이지만, 반응이 반응물을 소비해 정상 값이 낮아지므로 더 빨리 도달한다.$t_s=4.6/(k+1/\tau)=4.6/(0.2+0.2)=11.5$ min. Without reaction it would be $4.6\tau=23$ min; reaction lowers the steady value, so it is reached sooner.
What If?
만약에?What If?
만약 막 투과 계수 $k_C$를 한없이 키운다면?What if the membrane coefficient $k_C$ were made arbitrarily large?
클릭하여 확인 →Click to reveal →
B가 생기는 즉시 빠져나가 $F_B$가 0에 가까워지고, 역반응 항이 사라져 반응은 비가역 반응처럼 진행된다. 이 예제에서는 전환율이 99%를 넘고 그 이상은 거의 늘지 않는다. 실제 막은 A와 C도 조금 통과시키고(문제 6-6), 막 면적과 비용이 늘어나므로 $k_C$에는 경제적인 상한이 있다.B leaves as soon as it forms, $F_B$ approaches zero, the reverse term vanishes, and the reaction proceeds as if irreversible. In this example conversion exceeds 99% and gains almost nothing beyond that. Real membranes also leak some A and C (Problem 6-6), and area and cost grow, so $k_C$ has an economic limit.
만약 반회분식 반응기에서 B를 10배 빠르게 넣는다면?What if B were fed 10 times faster in a semibatch reactor?
클릭하여 확인 →Click to reveal →
B가 소비되기 전에 쌓여 $C_B$가 커지고 $C_A/C_B$가 작아지므로 $B^2$ 차수의 원치 않는 반응이 늘어 선택도가 떨어진다. 탱크도 같은 부피에 훨씬 일찍 도달해 A가 다 반응하기 전에 공급이 끝날 수 있다. 발열이 큰 반응이면 한꺼번에 열이 나오는 문제도 생긴다.B accumulates before it is consumed, $C_B$ rises and $C_A/C_B$ falls, so the undesired reaction with second-order dependence on B grows and selectivity drops. The vat also reaches its volume limit much sooner, so the feed may end before A has reacted. For a strongly exothermic reaction the heat release also arrives all at once.
만약 CSTR 안에서 반응이 전혀 일어나지 않는다면 시동 시간은?What if no reaction occurs in the CSTR: how long is startup?
클릭하여 확인 →Click to reveal →
$k=0$이면 $t_s=4.6\tau$이다. 탱크 안의 액체가 입구 농도의 용액으로 교체되는 시간만 필요하며, 공간 시간의 4.6배가 걸린다. 반응이 있으면 정상 값이 낮아지고 접근 속도 $1/\tau+k$가 커져서 시동이 더 빨라진다. 그래서 대부분의 1차 계에서 공간 시간의 3배에서 4배면 정상 상태에 닿는다.With $k=0$, $t_s=4.6\tau$: the tank liquid just has to be replaced by feed solution, which takes 4.6 space times. With reaction, the steady value is lower and the approach rate $1/\tau+k$ is larger, so startup is faster. Hence most first-order systems reach steady state in 3 to 4 space times.
Key Takeaways
01
모든 화학종에 몰 수지A Balance on Every Species
몰 유량 방식은 존재하는 모든 화학종에 몰 수지를 쓰고, 상대 속도로 $r_j$를 연결한 뒤 ODE solver로 푼다.The molar flow rate method writes a balance on every species, links the $r_j$ by relative rates, and solves with an ODE solver.
02
전환율로 풀 수 없는 경우When Conversion Is Not Enough
막 반응기, 기상 다중 반응, 비정상 상태 반응기는 몰 유량이나 농도를 변수로 써야 한다.Membrane reactors, multiple gas-phase reactions, and unsteady reactors need molar flow rates or concentrations as variables.
03
생성물 제거로 평형 넘기Removing a Product Beyond Equilibrium
막으로 생성물을 빼내거나 증류로 증발시키면 역반응이 줄어 전환율이 평형 전환율 $X_e$를 넘는다.Removing a product through a membrane or by distillation weakens the reverse reaction, so conversion exceeds the equilibrium value $X_e$.
04
비정상 상태 운전의 시간 규모Time Scales of Unsteady Operation
CSTR 시동은 공간 시간의 3배에서 4배가 걸리고, 반회분식 반응기는 공급 속도에 따라 선택도와 처리 시간이 서로 반대로 변한다.CSTR startup takes 3 to 4 space times, and a semibatch reactor trades selectivity against processing time through the feed rate.