Fogler, Elements of Chemical Reaction Engineering, Chapter 4. 슬라이더를 움직이면 그래프가 실시간으로 바뀝니다.Fogler, Elements of Chemical Reaction Engineering, Chapter 4. Move the sliders to see the graphs respond in real time.
화학양론표전환율과 농도액상 반응기상 반응과 $\varepsilon$평형 전환율
Section 4.1
회분계의 화학양론표Batch Systems
2장에서는 반응 속도 $-r_A$가 전환율 $X$의 함수로 주어졌다고 가정하고 반응기 크기를 정했다. $-r_A=f(X)$를 얻으려면 두 단계가 필요하다. 3장에서 반응 속도를 농도와 온도의 함수로 나타냈고, 이 장에서는 농도를 전환율로 나타낸다. 이 연결에 쓰는 도구가 화학양론표이다.In Chapter 2 we sized reactors assuming the rate $-r_A$ was known as a function of conversion $X$. Getting $-r_A=f(X)$ takes two steps. Chapter 3 expressed the rate in terms of concentration and temperature, and this chapter expresses concentration in terms of conversion. The tool for this link is the stoichiometric table.
일반 반응 $aA+bB\rightarrow cC+dD$에서 한계 반응물 A를 기준 물질로 잡고 모든 계수를 $a$로 나누어 A 1 mol당 양으로 바꾼다. 각 물질에 대해 처음 몰수, 반응으로 인한 변화량, 남은 몰수를 한 행에 적은 표가 화학양론표이다. 변화량은 항상 $N_{A0}X$에 계수비를 곱한 값이다.For the general reaction $aA+bB\rightarrow cC+dD$ we take the limiting reactant A as the basis of calculation and divide every coefficient by $a$, so everything is per mole of A. The stoichiometric table lists, for each species, the initial moles, the change due to reaction, and the moles remaining. Each change equals $N_{A0}X$ times the coefficient ratio.
회분 반응기에서 부피가 일정하면 $V=V_0$이므로 몰수를 부피로 나누기만 하면 농도가 나온다. 정압 기상 회분계에서는 전체 몰수가 변하므로 부피가 전환율과 함께 변한다. 이 경우는 4.2.3에서 흐름계와 함께 다룬다.In a rigid batch reactor $V=V_0$, so dividing moles by volume gives concentration directly. In a constant-pressure gas-phase batch system the total moles change, so the volume varies with conversion. That case is treated in Section 4.2.3 together with flow systems.
기준 물질 A: 한계 반응물을 기준으로 삼아 전환율 $X=(N_{A0}-N_A)/N_{A0}$를 정의한다.Basis species A: the limiting reactant defines conversion $X=(N_{A0}-N_A)/N_{A0}$.
과잉비 $\Theta_i$: 물질 $i$의 처음 몰수를 A의 처음 몰수로 나눈 값이다. $\Theta_B$가 $b/a$보다 작으면 B가 먼저 소진된다.Feed ratio $\Theta_i$: initial moles of species $i$ divided by initial moles of A. If $\Theta_B$ is below $b/a$, B is exhausted first.
$\delta$: A 1 mol이 반응할 때 전체 몰수의 증가량이다. 생성물 계수의 합에서 반응물 계수의 합을 빼고 $a$로 나눈 값이다.$\delta$: the increase in total moles per mole of A reacted, the sum of product coefficients minus the sum of reactant coefficients, divided by $a$.
Figure 4.1전환율에 따른 화학양론표의 몰수 변화Stoichiometric table moles as conversion changes
예측: 회분 반응 $A+2B\rightarrow C$에서 A와 B를 같은 몰수로 넣었다($\Theta_B=1$). 전환율을 올리면 어느 물질이 먼저 소진될까?Predict: In the batch reaction $A+2B\rightarrow C$, A and B are fed in equal moles ($\Theta_B=1$). Which species runs out first as conversion rises?
목표: 그림 아래쪽 막대의 핸들을 끌어 첫 반응물이 정확히 소진되는 $X$를 찾으세요(오차 0.02 이내). $\Theta_B$를 바꾸면 소진되는 물질도 바뀝니다.Goal: drag the handle on the bar at the bottom to find the $X$ where the first reactant is exactly used up (within 0.02). Changing $\Theta_B$ changes which species runs out.
과잉비 $\Theta_B$Feed ratio $\Theta_B$1.0
전환율 XConversion X0.00
소진 한계 XLimit X0.50
N_B (mol)N_B (mol)10.0
N_T (mol)N_T (mol)20.0
$N_B=N_{A0}(\Theta_B-2X)$가 0이 되는 $X=\Theta_B/2$가 B의 소진점이다. 이 지점을 넘으면 몰수가 음수가 되어 물리적으로 불가능하다. 이 반응은 $\delta=-2$이므로 전체 몰수 $N_T$도 전환율에 비례해 줄어든다. 처음 몰수 $N_{A0}=10$ mol은 그림용 값이다.$N_B=N_{A0}(\Theta_B-2X)$ reaches zero at $X=\Theta_B/2$, the exhaustion point of B. Beyond it the mole count would be negative, which is physically impossible. Since $\delta=-2$ here, the total moles $N_T$ also fall linearly with conversion. The basis $N_{A0}=10$ mol is an illustration value.
Section 4.2
흐름계와 액상 농도Flow Systems and Liquid-Phase Concentrations
흐름계에서는 몰수 대신 몰유량 $F_j$를 쓴다. 화학양론표의 구조는 같고 $N$이 $F$로, $N_{A0}$가 $F_{A0}$로 바뀐다. 농도는 몰유량을 부피유량 $v$로 나눈 값이다. 따라서 $v$가 전환율에 따라 어떻게 변하는지를 알아야 농도를 구할 수 있다.In flow systems we use molar flow rates $F_j$ instead of moles. The table has the same structure, with $N$ replaced by $F$ and $N_{A0}$ by $F_{A0}$. Concentration is molar flow rate divided by volumetric flow rate $v$, so we must know how $v$ changes with conversion.
액상 반응에서는 밀도 변화가 작으므로 $v=v_0$로 둔다. 그러면 농도는 전환율에 대해 일차 함수로 나타난다. 회분계의 부피 일정 조건과 식이 같다. 제한 반응물이 아닌 물질의 농도는 $\Theta_B$에 따라 올라가거나 내려간다. 2차 반응 $A+B\rightarrow C$에서는 $-r_A=kC_AC_B$에 이 농도식을 넣어 $-r_A$를 $X$만의 함수로 쓴다.In liquid-phase reactions density changes are small, so we take $v=v_0$. Concentrations are then linear in conversion, the same expressions as for a constant-volume batch system. The concentration of a species other than the limiting reactant rises or falls with $\Theta_B$. For the second-order reaction $A+B\rightarrow C$, substituting these into $-r_A=kC_AC_B$ gives $-r_A$ as a function of $X$ alone.
$-r_A=f(X)$: 속도식의 모든 농도를 $X$로 바꾸면 반응기 설계식에 바로 넣을 수 있는 형태가 된다.$-r_A=f(X)$: once every concentration in the rate law is written in terms of $X$, the rate goes straight into the design equation.
과잉 반응물: $\Theta_B$가 $b/a$보다 훨씬 크면 $C_B$가 거의 일정하여 속도식이 A에 대한 유사 1차식으로 단순해진다.Excess reactant: if $\Theta_B$ is much larger than $b/a$, $C_B$ stays nearly constant and the rate law reduces to pseudo-first order in A.
Figure 4.2액상 반응 $A+B\rightarrow C$의 농도와 반응 속도Concentrations and rate of the liquid-phase reaction $A+B\rightarrow C$
과잉비 $\Theta_B$Feed ratio $\Theta_B$1.5
전환율 $X$Conversion $X$0.40
C_A (mol/dm3)C_A (mol/dm3)0
C_B (mol/dm3)C_B (mol/dm3)0
-r_A (mol/dm3/min)-r_A (mol/dm3/min)0
$C_{A0}=2.0$ mol/dm3, $k=0.1$ dm3/(mol min)은 이 그림을 위해 정한 예시 값이다. $\Theta_B<1$이면 B가 한계 반응물이 되어 $X$ 축이 $\Theta_B$에서 끝난다. $\Theta_B$를 키울수록 $-r_A$가 느리게 감소한다.$C_{A0}=2.0$ mol/dm3 and $k=0.1$ dm3/(mol min) are illustration values chosen for this plot. For $\Theta_B<1$, B is limiting and the $X$ axis stops at $\Theta_B$. A larger $\Theta_B$ makes $-r_A$ decay more slowly.
Section 4.2.3
기상 반응의 부피유량과 농도Gas-Phase Volumetric Flow and Concentrations
기체의 부피유량은 전환율, 온도, 압력에 따라 변한다. 이상기체에서 전체 몰유량 $F_T=F_{T0}+F_{A0}\delta X$이고, $v=F_TRT/P$이다. 처음 상태와 비를 취하면 $v=v_0(1+\varepsilon X)(P_0/P)(T/T_0)$를 얻는다. 여기서 $\varepsilon=y_{A0}\delta$는 $X=1$일 때 부피유량이 처음의 몇 배 늘어나는지를 나타낸다.The volumetric flow rate of a gas varies with conversion, temperature, and pressure. For an ideal gas the total molar flow is $F_T=F_{T0}+F_{A0}\delta X$ and $v=F_TRT/P$. Taking the ratio to the inlet state gives $v=v_0(1+\varepsilon X)(P_0/P)(T/T_0)$. Here $\varepsilon=y_{A0}\delta$ is the fractional increase in volumetric flow rate at complete conversion.
$\varepsilon$는 $\delta$뿐 아니라 A의 처음 몰분율 $y_{A0}$에도 비례한다. 같은 $A\rightarrow 3B$ 반응이라도 순수 A를 공급하면 $\varepsilon=2$이고, A와 불활성 기체를 절반씩 공급하면 $\varepsilon=1$이다. 불활성 기체를 섞으면 팽창이 줄어든다.$\varepsilon$ is proportional not only to $\delta$ but also to the inlet mole fraction $y_{A0}$. For the same reaction $A\rightarrow 3B$, a pure A feed gives $\varepsilon=2$, while a feed of half A and half inert gives $\varepsilon=1$. The inert dilutes the expansion.
$\varepsilon>0$이면 전환이 진행될수록 기체가 팽창하여 농도가 액상 반응보다 더 빨리 낮아진다. $\varepsilon<0$이면 부피가 줄어 농도가 상대적으로 높게 유지된다. 압력이 낮아지거나 온도가 올라가도 같은 방향으로 농도가 낮아진다. 촉매 기상 반응의 속도식은 분압으로 쓰이므로 $P_A=C_ART$도 전환율의 함수로 쓴다.For $\varepsilon>0$ the gas expands as conversion proceeds, so concentration falls faster than in a liquid-phase reaction. For $\varepsilon<0$ the volume shrinks and concentration stays relatively high. Lower pressure or higher temperature also lowers concentration. Rate laws of gas-solid catalytic reactions use partial pressures, so $P_A=C_ART$ is also written as a function of conversion.
$\varepsilon$의 부호: 몰수가 늘어나는 반응($\delta>0$)은 $\varepsilon>0$, 줄어드는 반응은 $\varepsilon<0$, 몰수가 같은 반응은 $\varepsilon=0$이어서 액상 식과 같아진다.Sign of $\varepsilon$: reactions that add moles ($\delta>0$) have $\varepsilon>0$, those that remove moles have $\varepsilon<0$, and equimolar reactions have $\varepsilon=0$, recovering the liquid-phase expressions.
압력과 온도 비: 등온 정압 운전이면 $P/P_0=T/T_0=1$이어서 $C_A=C_{A0}(1-X)/(1+\varepsilon X)$로 단순해진다.Pressure and temperature ratios: for isothermal constant-pressure operation $P/P_0=T/T_0=1$ and $C_A=C_{A0}(1-X)/(1+\varepsilon X)$.
Figure 4.3$\delta$와 $\varepsilon$에 따른 기체 팽창과 $C_A$ 감소Gas expansion and falling $C_A$ as a function of $\delta$ and $\varepsilon$
예측: 반응 $A\rightarrow(1+\delta)B$에서 $\delta$를 키워 $\varepsilon$를 올리면, 같은 전환율에서 $C_A/C_{A0}$는 어떻게 될까?Predict: For $A\rightarrow(1+\delta)B$, if we raise $\delta$ and so $\varepsilon$, what happens to $C_A/C_{A0}$ at the same conversion?
목표: 위쪽 용기의 점선(전환율 1에서의 오른쪽 벽)을 좌우로 끌어 $\delta$를 바꾸고, $X=0.5$에서 $C_A/C_{A0}$가 0.25 이하가 되게 하세요. $y_{A0}$ 슬라이더도 함께 조절하세요.Goal: drag the dashed line (the right wall at $X=1$) of the upper vessel left or right to change $\delta$, so that $C_A/C_{A0}$ at $X=0.5$ is 0.25 or lower. Adjust the $y_{A0}$ slider as well.
A의 처음 몰분율 $y_{A0}$Inlet mole fraction $y_{A0}$0.50
δδ1.00
εε0.50
X=1에서 v/v0v/v0 at X=11.50
X=0.5에서 C_A/C_A0C_A/C_A0 at X=0.50.40
등온 정압이면 전체 농도는 일정하고 용기 부피만 $1+\varepsilon X$배로 커진다. A는 반응으로 줄고 부피 팽창으로 한 번 더 희석되므로 $C_A/C_{A0}=(1-X)/(1+\varepsilon X)$는 액상(회색선)보다 아래에 놓인다. $\varepsilon$의 상한은 $y_{A0}\delta$이므로 $\delta$가 작거나 불활성 기체가 많으면 목표에 도달하지 못한다.At constant T and P the total concentration is constant and only the vessel volume grows by $1+\varepsilon X$. A is consumed and diluted once more by expansion, so $C_A/C_{A0}=(1-X)/(1+\varepsilon X)$ lies below the liquid-phase line (gray). The limit on $\varepsilon$ is $y_{A0}\delta$, so a small $\delta$ or a lot of inert makes the goal unreachable.
Figure 4.4$\varepsilon$, 압력비, 온도비에 따른 $C_A$와 $v$$C_A$ and $v$ versus $\varepsilon$, pressure ratio, and temperature ratio
$\varepsilon$1.0
$P/P_0$1.00
$T/T_0$1.00
전환율 $X$Conversion $X$0.50
C_A / C_A0C_A / C_A00
v / v0v / v00
P_A / P_A0P_A / P_A00
그림은 4.2.3의 식을 그대로 그린 것이며 무차원 비만 쓰므로 물성값이 필요 없다. 점선은 $\varepsilon=0$인 기준선이다. $P/P_0$를 낮추거나 $T/T_0$를 높이면 $v$가 늘어 $C_A$가 같은 비율로 낮아진다.The plot draws the Section 4.2.3 expressions directly and uses only dimensionless ratios, so no property data are needed. The dotted line is the reference $\varepsilon=0$. Lowering $P/P_0$ or raising $T/T_0$ increases $v$ and lowers $C_A$ by the same factor.
Section 4.3
가역 반응과 평형 전환율Reversible Reactions and Equilibrium Conversion
가역 반응의 등온 반응기 설계는 비가역 반응과 거의 같고, 한 가지만 다르다. 반응이 도달할 수 있는 최대 전환율이 평형 전환율 $X_e$로 제한된다. 평형에서는 농도가 열역학에서 정해진 농도 평형 상수 $K_C$를 만족한다. $K_C$에 평형 농도를 $X_e$로 나타내어 넣으면 $X_e$를 풀 수 있다.Isothermal design for a reversible reaction is nearly the same as for an irreversible one, with one difference. The maximum attainable conversion is limited to the equilibrium conversion $X_e$. At equilibrium the concentrations satisfy the concentration equilibrium constant $K_C$ fixed by thermodynamics. Writing the equilibrium concentrations in terms of $X_e$ and substituting into $K_C$ gives $X_e$.
Example 4-5는 기상 분해 반응 $N_2O_4\rightleftharpoons 2NO_2$이다. 340 K, 2 atm에서 순수 $N_2O_4$를 공급하면 $C_{A0}=P_0/RT=0.0717$ mol/dm3이고 $K_C=0.1$ mol/dm3이다. 부피가 일정한 회분 반응기에서는 $X_e=0.44$이고, 압력이 일정한 흐름계에서는 $\varepsilon=1$이므로 $X_e=0.51$이다. 같은 $K_C$에서도 계의 조건에 따라 평형 전환율이 다르다.Example 4-5 is the gas-phase decomposition $N_2O_4\rightleftharpoons 2NO_2$. Pure $N_2O_4$ at 340 K and 2 atm gives $C_{A0}=P_0/RT=0.0717$ mol/dm3, with $K_C=0.1$ mol/dm3. In a constant-volume batch reactor $X_e=0.44$, while in a constant-pressure flow system $\varepsilon=1$ and $X_e=0.51$. The same $K_C$ gives different equilibrium conversions depending on the system.
몰수가 늘어나는 반응에서 압력을 높이면 $C_{A0}$가 커져 $X_e$가 내려간다. 몰수가 같은 반응($\delta=0$)에서는 압력이 $X_e$에 영향을 주지 않는다. 몰수가 줄어드는 반응은 압력을 높일수록 $X_e$가 올라간다.For a reaction that adds moles, raising the pressure increases $C_{A0}$ and lowers $X_e$. For an equimolar reaction ($\delta=0$) pressure has no effect on $X_e$. For a reaction that removes moles, raising pressure raises $X_e$.
평형 전환율 $X_e$: 정반응과 역반응 속도가 같아져 $-r_A=0$이 되는 전환율이다. 이 값을 넘는 전환율은 얻을 수 없다.Equilibrium conversion $X_e$: the conversion at which forward and reverse rates are equal and $-r_A=0$. No larger conversion can be reached.
정용 대 정압: 정용 회분계는 $C_A=C_{A0}(1-X)$이고 정압 흐름계는 $\varepsilon$에 따라 부피가 변하므로 같은 $K_C$에서 $X_e$가 다르다.Constant volume versus constant pressure: the constant-volume batch has $C_A=C_{A0}(1-X)$, while the constant-pressure flow system changes volume with $\varepsilon$, so $X_e$ differs for the same $K_C$.
Figure 4.5압력과 $K_C$에 따른 평형 전환율 $X_e$Equilibrium conversion $X_e$ versus pressure and $K_C$
예측: 정압 흐름계의 $A\rightleftharpoons 2B$에서 압력을 올리면 $X_e$는 어떻게 될까?Predict: For $A\rightleftharpoons 2B$ in a constant-pressure flow system, what happens to $X_e$ when pressure rises?
목표: $A\rightleftharpoons 2B$, 정압 흐름계에서 $X_e=0.80$(오차 0.02 이내)이 되도록 압력 슬라이더를 움직이고, 그림의 수평선(KC)을 위아래로 끌어 조정하세요.Goal: for $A\rightleftharpoons 2B$ in a constant-pressure flow system, reach $X_e=0.80$ (within 0.02) by moving the pressure slider and dragging the horizontal line ($K_C$) up or down in the plot.
압력 $P$ (atm)Pressure $P$ (atm)2.0
$\log_{10}K_C$$\log_{10}K_C$0.100
C_A0 (mol/dm3)C_A0 (mol/dm3)0
평형 전환율 X_eEquilibrium X_e0
C_A,e (mol/dm3)C_A,e (mol/dm3)0
C_B,e (mol/dm3)C_B,e (mol/dm3)0
곡선은 전환율 $X$에서 계산한 $C_B^p/C_A^q$이고, 수평선이 주어진 $K_C$이다. 두 선이 만나는 $X$가 $X_e$이다. $T=340$ K로 고정하고 $C_{A0}=P/RT$로 계산했다. 기본값(2 atm, $K_C=0.1$)은 Example 4-5의 값으로, 정압 흐름에서 0.51, 정용 회분에서 0.44가 나온다. $A\rightleftharpoons B$는 압력과 관계없이 $X_e=K_C/(1+K_C)$이다.The curve is $C_B^p/C_A^q$ evaluated at conversion $X$, and the horizontal line is the given $K_C$. The $X$ where they meet is $X_e$. $T$ is fixed at 340 K and $C_{A0}=P/RT$. The default (2 atm, $K_C=0.1$) is the Example 4-5 case, giving 0.51 for constant-pressure flow and 0.44 for constant-volume batch. For $A\rightleftharpoons B$, $X_e=K_C/(1+K_C)$ regardless of pressure.
Summary
등온 반응기 설계 알고리즘 미리 보기Preview of the Isothermal Reactor Design Algorithm
이 장으로 CRE 설계의 세 요소가 모였다. 몰수지(mole balance)가 반응기 부피와 $-r_A$를 연결하고, 속도식(rate law)이 $-r_A$를 농도로 나타내며, 화학양론이 농도를 전환율로 나타낸다. 세 식을 결합하면 $-r_A$가 $X$만의 함수가 되어 CSTR과 PFR의 부피를 계산할 수 있다.This chapter completes three building blocks of CRE design. The mole balance relates reactor volume to $-r_A$, the rate law expresses $-r_A$ in terms of concentration, and stoichiometry expresses concentration in terms of conversion. Combining them makes $-r_A$ a function of $X$ alone, so CSTR and PFR volumes can be computed.
Example 4-5의 흐름계에서 $F_{A0}=3.0$ mol/min, $k=0.5$ min-1이면 $X=0.4$에서 $-r_A=0.0070$ mol/dm3/min이고, CSTR 부피는 0.171 m3이다. 이 값은 Levenspiel 도표에서 $F_{A0}/(-r_A)$ 곡선 아래의 직사각형 넓이와 같다. 다음 장에서는 이 계산을 적분표와 Polymath로 바꾼다.For the flow system of Example 4-5 with $F_{A0}=3.0$ mol/min and $k=0.5$ min-1, $-r_A=0.0070$ mol/dm3/min at $X=0.4$ and the CSTR volume is 0.171 m3. This equals the rectangle area under the $F_{A0}/(-r_A)$ curve on a Levenspiel plot. The next chapter replaces this calculation with integral tables and Polymath.
순서: 몰수지, 속도식, 화학양론, 결합, 계산 순으로 진행한다. 이 장은 화학양론 단계이다.Order: mole balance, rate law, stoichiometry, combine, evaluate. This chapter supplies the stoichiometry step.
$X_e$ 근처: 전환율이 $X_e$에 가까워지면 $-r_A\rightarrow 0$이므로 필요한 부피가 무한히 커진다.Near $X_e$: as conversion approaches $X_e$, $-r_A\rightarrow 0$ and the required volume grows without bound.
Figure 4.6$N_2O_4$ 분해 반응의 Levenspiel 도표와 CSTR 부피Levenspiel plot and CSTR volume for $N_2O_4$ decomposition
예측: 같은 전환율 $X=0.4$를 얻는 데 CSTR과 PFR 중 어느 쪽 부피가 작을까?Predict: To reach the same conversion $X=0.4$, which reactor volume is smaller, CSTR or PFR?
목표: 그림의 세로선을 끌어 $X$를 평형 전환율의 80%(0.406, 오차 0.01 이내)에 맞추고, 그때의 CSTR 부피를 읽으세요. $X_e$에 가까워질수록 부피가 어떻게 되는지도 확인하세요.Goal: drag the vertical line to set $X$ to 80% of the equilibrium conversion (0.406, within 0.01) and read the CSTR volume. Also watch what happens to the volume as $X$ approaches $X_e$.
전환율 XConversion X0.000
X / X_eX / X_e0.00
V_CSTR (dm3)V_CSTR (dm3)0
V_PFR (dm3)V_PFR (dm3)0
파란 영역(곡선 아래 넓이)이 PFR 부피, 빨간 직사각형이 CSTR 부피이다. $F_{A0}/(-r_A)$가 $X$와 함께 증가하므로 같은 $X$에서 PFR이 더 작다. 값은 Example 4-5의 $F_{A0}=3.0$ mol/min, $k=0.5$ min-1, $K_C=0.1$ mol/dm3, $C_{A0}=0.0717$ mol/dm3을 쓰고, $X=0.4$에서 CSTR 부피가 약 172 dm3이다.The blue area under the curve is the PFR volume and the red rectangle is the CSTR volume. Since $F_{A0}/(-r_A)$ increases with $X$, the PFR is smaller at the same $X$. Values are from Example 4-5: $F_{A0}=3.0$ mol/min, $k=0.5$ min-1, $K_C=0.1$ mol/dm3, $C_{A0}=0.0717$ mol/dm3, giving a CSTR volume of about 172 dm3 at $X=0.4$.
Quiz
확인 문제Check Your Understanding
반응 $A\rightarrow 3B$에 A 50 mol%와 불활성 기체 50 mol%를 공급할 때 $\varepsilon$은?For $A\rightarrow 3B$ fed with 50 mol% A and 50 mol% inert, what is $\varepsilon$?
$\delta=3-1=2$이고 $y_{A0}=0.5$이므로 $\varepsilon=y_{A0}\delta=1.0$이다. 순수 A를 공급하면 $\varepsilon=2$이다.$\delta=3-1=2$ and $y_{A0}=0.5$, so $\varepsilon=y_{A0}\delta=1.0$. A pure A feed would give $\varepsilon=2$.
등온 정압 기상 반응에서 $\varepsilon>0$이면 같은 전환율의 $C_A$는 액상 반응($\varepsilon=0$)과 비교해 어떠한가?In an isothermal constant-pressure gas-phase reaction with $\varepsilon>0$, how is $C_A$ at a given conversion compared with a liquid-phase reaction ($\varepsilon=0$)?
$C_A=C_{A0}(1-X)/(1+\varepsilon X)$에서 분모가 1보다 크므로 $C_A$가 더 작다. 기체가 팽창하며 농도가 낮아지기 때문이다.In $C_A=C_{A0}(1-X)/(1+\varepsilon X)$ the denominator exceeds 1, so $C_A$ is smaller. The gas expands and dilutes.
$N_2O_4\rightleftharpoons 2NO_2$를 같은 $K_C$, 같은 처음 상태에서 운전할 때 평형 전환율이 더 큰 쪽은?For $N_2O_4\rightleftharpoons 2NO_2$ with the same $K_C$ and initial state, which system has the larger equilibrium conversion?
정용 계는 몰수가 늘면 압력이 올라가 평형이 반응물 쪽으로 이동한다. 정압 계는 부피가 늘어 농도가 낮아지므로 분해가 더 진행되어 $X_e=0.51$이 되고, 정용 계는 $X_e=0.44$이다.In the constant-volume system the pressure rises as moles are added, pushing equilibrium back toward reactant. The constant-pressure system expands and dilutes, so more decomposition occurs: $X_e=0.51$ versus $X_e=0.44$ for constant volume.
What If?
만약에?What If?
만약 몰수가 늘어나는 기상 반응에 불활성 기체를 섞으면?What if an inert gas is added to a gas-phase reaction that increases moles?
클릭하여 확인 →Click to reveal →
$y_{A0}$가 줄어 $\varepsilon=y_{A0}\delta$가 작아지고, 반응물 농도도 낮아진다. 평형 전환율은 반응물 분압이 낮아진 효과로 올라가지만, 같은 부피에서 처리하는 A의 양은 줄어든다.$y_{A0}$ falls, so $\varepsilon=y_{A0}\delta$ shrinks and the reactant concentration drops. The equilibrium conversion rises because of the lower reactant partial pressure, but less A is processed per unit volume.
만약 $\delta=0$인 기상 반응($A\rightleftharpoons B$)의 압력을 10배 올리면?What if the pressure of a gas-phase reaction with $\delta=0$ ($A\rightleftharpoons B$) is raised tenfold?
클릭하여 확인 →Click to reveal →
$C_{A0}$는 10배가 되지만 $K_C=C_B/C_A$는 농도 비이므로 $X_e=K_C/(1+K_C)$는 변하지 않는다. 속도는 농도에 따라 빨라지므로 같은 전환율에 이르는 시간은 짧아진다.$C_{A0}$ becomes ten times larger, but $K_C=C_B/C_A$ is a ratio of concentrations, so $X_e=K_C/(1+K_C)$ is unchanged. The rate rises with concentration, so the same conversion is reached sooner.
만약 액상 반응 $A+B\rightarrow C$에서 B를 매우 과량($\Theta_B=50$)으로 넣으면?What if B is fed in large excess ($\Theta_B=50$) in the liquid-phase reaction $A+B\rightarrow C$?
클릭하여 확인 →Click to reveal →
$C_B=C_{A0}(\Theta_B-X)$는 $X$가 0에서 1까지 변해도 2% 안에서 일정하다. 속도식은 $-r_A\approx(kC_B)C_A$가 되어 A에 대한 유사 1차 반응으로 취급할 수 있다.$C_B=C_{A0}(\Theta_B-X)$ varies by only about 2% as $X$ goes from 0 to 1. The rate becomes $-r_A\approx(kC_B)C_A$, which can be treated as pseudo-first order in A.
Key Takeaways
01
화학양론표Stoichiometric table
기준 물질 A를 정하고 $N_j=N_{A0}(\Theta_j+\nu_jX)$로 모든 물질의 몰수를 전환율에 연결한다.Choose basis species A and link every species to conversion by $N_j=N_{A0}(\Theta_j+\nu_jX)$.
02
액상은 $v=v_0$Liquid: $v=v_0$
액상 반응의 농도는 전환율의 일차식이다. 속도식이 $X$만의 함수가 된다.Liquid-phase concentrations are linear in conversion, so the rate law becomes a function of $X$ alone.
03
기상은 $\varepsilon$로 팽창 보정Gas: correct for expansion with $\varepsilon$
$v=v_0(1+\varepsilon X)(P_0/P)(T/T_0)$이다. $\varepsilon=y_{A0}\delta$가 양수이면 농도가 더 빨리 낮아진다.$v=v_0(1+\varepsilon X)(P_0/P)(T/T_0)$. A positive $\varepsilon=y_{A0}\delta$ makes concentration fall faster.
04
평형 전환율이 상한$X_e$ is the ceiling
가역 반응의 전환율은 $X_e$를 넘지 못한다. $X_e$는 $K_C$, 압력, 정용 또는 정압 조건에 따라 달라진다.Conversion in a reversible reaction cannot exceed $X_e$, which depends on $K_C$, pressure, and constant-volume or constant-pressure operation.