비이상 반응기 모형: 탱크 직렬과 분산Models for Nonideal Reactors: Tanks in Series and Dispersion
Fogler, Elements of Chemical Reaction Engineering, Chapter 18. 탱크 수와 Peclet 수를 조절하면 추적자 곡선과 전환율이 실시간으로 바뀐다.Fogler, Elements of Chemical Reaction Engineering, Chapter 18. Drag the number of tanks and the Peclet number and watch tracer curves and conversion respond in real time.
탱크 직렬 모형분산 모형과 Peclet 수Danckwerts 경계 조건분산 계수 상관식바이패스와 데드 볼륨추적자 자료 맞춤
Section 18.1
비이상 반응기 모형을 세우는 순서Some Guidelines for Developing Models
실제 반응기는 채널링, 바이패스, 정체 영역(dead zone) 때문에 이상적인 PFR 또는 CSTR의 흐름과 다르게 흐른다. 16장과 17장에서 추적자 실험으로 체류 시간 분포(RTD) $E(t)$를 얻었지만, RTD만으로는 일반적인 속도식의 전환율을 구할 수 없다. 그래서 이상 반응기 몇 개를 조합한 모형을 세우고, 그 모형의 RTD가 측정한 RTD와 같아지도록 매개변수를 정한다.Real reactors flow differently from an ideal PFR or CSTR because of channeling, bypassing, and dead zones. Chapters 16 and 17 gave the residence time distribution (RTD) $E(t)$ from tracer tests, but the RTD alone cannot give the conversion of a general rate law. So we build a model from a few ideal reactors and choose its parameters so that the model RTD equals the measured RTD.
모형은 매개변수 개수로 나눈다. 매개변수가 하나인 모형은 탱크 직렬 모형의 탱크 수 $n$과 분산 모형의 Peclet 수 $\mathrm{Pe}_r$이다. 매개변수가 둘인 모형은 바이패스 유량과 데드 볼륨처럼 이상 반응기를 조합해서 만든다. 매개변수가 적을수록 계산이 쉽지만, 측정한 RTD를 설명하지 못하면 매개변수를 하나 더 늘린다.Models are classified by their number of parameters. The one-parameter models are the number of tanks $n$ in the tanks-in-series model and the Peclet number $\mathrm{Pe}_r$ in the dispersion model. Two-parameter models combine ideal reactors, for example with a bypass flow and a dead volume. Fewer parameters make the calculation easier, but if the model cannot reproduce the measured RTD, one more parameter is added.
모형화 순서: (1) 반응기 내부의 흐름을 살펴 채널링이나 정체 영역이 있는지 판단한다. (2) 추적자로 RTD를 측정한다. (3) 모형을 고르고 RTD와 정성적으로 비교한다. (4) 매개변수를 RTD에서 구한다. (5) 속도식과 모형으로 전환율을 계산한다.Modeling steps: (1) inspect the flow for channeling and dead zones, (2) measure the RTD with a tracer, (3) choose a model and compare it qualitatively with the RTD, (4) obtain the parameters from the RTD, (5) compute conversion from the rate law and the model.
비이상성의 세 가지 원인: 채널링은 일부 유체가 평균보다 빨리 지나가는 것이고, 바이패스는 유체 일부가 반응 영역을 거치지 않고 출구로 가는 것이며, 데드 볼륨은 유체가 거의 교환되지 않는 영역이다.Three causes of nonideality: channeling is some fluid passing faster than average, bypassing is part of the feed reaching the outlet without entering the reaction zone, and a dead volume is a region where fluid is hardly exchanged.
Section 18.2
탱크 직렬 모형The Tanks-in-Series One-Parameter Model
탱크 직렬(T-I-S) 모형은 부피가 같은 CSTR $n$개를 직렬로 연결한 계의 RTD가 실제 반응기의 RTD와 같아지는 $n$을 찾는다. 추적자 펄스를 첫 탱크에 넣고 탱크마다 추적자 수지를 쓰면 $n$번째 탱크 출구의 $E(t)$가 얻어진다. 각 탱크의 공간 시간은 $\tau_i=\tau/n$이다.The tanks-in-series (T-I-S) model finds the number $n$ of equal-volume CSTRs in series whose RTD equals that of the real reactor. Inject a tracer pulse into the first tank, write a tracer balance on each tank, and the outlet of tank $n$ gives $E(t)$. Each tank has space time $\tau_i=\tau/n$.
$n=1$이면 CSTR의 $e^{-\Theta}$이고, $n$이 커질수록 피크가 $\Theta=1$ 쪽으로 모이며 폭이 줄어서 PFR의 delta 함수에 가까워진다. 무차원 분산은 $\sigma_\Theta^2=\sigma^2/\tau^2=1/n$이므로, 측정한 RTD에서 평균 체류 시간 $t_m$과 분산 $\sigma^2$를 구하면 탱크 수가 정해진다. 예제 18-1에서는 이렇게 구한 $n$이 4.35이다.For $n=1$ this is the CSTR result $e^{-\Theta}$; as $n$ grows the peak moves toward $\Theta=1$ and narrows toward the PFR delta function. The dimensionless variance is $\sigma_\Theta^2=\sigma^2/\tau^2=1/n$, so the mean residence time $t_m$ and variance $\sigma^2$ of the measured RTD fix the number of tanks. In Example 18-1 this gives $n=4.35$.
$n$이 정해지면 1차 반응의 전환율은 탱크를 하나씩 지나며 농도가 $1/(1+\tau_i k)$배로 줄어드는 것을 $n$번 곱해서 얻는다. $n$이 정수가 아니어도 아래 식을 그대로 쓸 수 있고, 가까운 두 정수 탱크 수로 전환율의 범위를 잡는다. 1차가 아닌 반응은 탱크를 차례로 풀어야 하며, 이 점이 T-I-S 모형을 쓰는 이유이다.Once $n$ is fixed, the first-order conversion follows from the concentration being multiplied by $1/(1+\tau_i k)$ in each of the $n$ tanks. If $n$ is not an integer, use the formula below as written or bracket the conversion with the two nearest integers. Reactions other than first order are solved tank by tank, which is the reason to use the T-I-S model.
$\sigma_\Theta^2=1/n$: 탱크가 많을수록 분산이 작고 RTD가 좁다. $n\to\infty$에서 PFR이 된다.$\sigma_\Theta^2=1/n$: more tanks give smaller variance and a narrower RTD. As $n\to\infty$ the PFR is recovered.
탱크 수는 정수가 아니어도 된다: 감마 함수로 $(n-1)!$를 $\Gamma(n)$으로 바꾸면 $n=4.35$ 같은 값도 정의된다. 실제 반응기가 정수 탱크로 이루어진 것은 아니기 때문이다.$n$ need not be an integer: replacing $(n-1)!$ by $\Gamma(n)$ defines values such as $n=4.35$. The real reactor is not made of a whole number of tanks.
Figure 18.1탱크 수 $n$에 따른 추적자 이동과 $E(\Theta)$ 변화Tracer Passing Through $n$ Tanks and the Change of $E(\Theta)$
예측: 탱크 수 $n$을 1에서 늘리면 출구 추적자 곡선 $E(\Theta)$는 어떻게 될까?Predict: as the number of tanks $n$ increases from 1, what happens to the outlet tracer curve $E(\Theta)$?
목표: 그림 아래 막대의 핸들을 좌우로 끌어 탱크 수를 바꾸고, 계의 무차원 분산 $1/n$이 측정값 $\sigma_\Theta^2=0.23$의 10% 이내가 되게 하세요. 빨간 점선이 측정한 RTD입니다.Goal: drag the handle on the bar below the figure to change the number of tanks until the dimensionless variance $1/n$ is within 10% of the measured $\sigma_\Theta^2=0.23$. The red dashed curve is the measured RTD.
탱크 수 nTanks n—
모형 분산 1/nModel variance 1/n—
측정 분산 대비 오차Error vs measured—
1차 전환율 ($k\tau=2$)First-order X ($k\tau=2$)—
탱크마다 $dC_i/d\Theta=n(C_{i-1}-C_i)$를 직접 적분한 결과이고, 측정 곡선은 예제 18-1의 $n=4.35$에 해당하는 감마 분포로 다시 만든 값이다. 탱크를 늘릴수록 전환율이 PFR 값 0.865에 가까워지므로, 분산이 작다는 것은 같은 부피에서 전환율이 높다는 뜻이다.Each tank is integrated directly from $dC_i/d\Theta=n(C_{i-1}-C_i)$, and the measured curve is rebuilt as the gamma distribution for $n=4.35$ of Example 18-1. More tanks push the conversion toward the PFR value of 0.865, so a smaller variance means higher conversion at the same volume.
Q1. 추적자 펄스 실험에서 평균 체류 시간 $t_m=10$ min, 분산 $\sigma^2=25$ min$^2$를 얻었다. T-I-S 모형의 탱크 수는?Q1. A tracer pulse test gives $t_m=10$ min and $\sigma^2=25$ min$^2$. What is the number of tanks in the T-I-S model?
$n=t_m^2/\sigma^2=100/25=4$이다. 분산 $\sigma^2$을 $t_m^2$으로 나누지 않고 그대로 쓰거나 $\sigma^2/t_m^2=0.25$를 탱크 수로 읽으면 틀린다. 0.25는 무차원 분산이고 탱크 수는 그 역수이다.$n=t_m^2/\sigma^2=100/25=4$. Using the dimensional variance without dividing by $\tau^2$, or reading $\sigma^2/t_m^2=0.25$ as the number of tanks, is wrong: 0.25 is the dimensionless variance and the tank number is its reciprocal.
Section 18.3
분산 모형과 경계 조건The Dispersion Model and Its Boundary Conditions
분산 모형은 PFR의 축 방향 흐름에 확산과 비슷한 혼합 항을 더한다. 추적자 수지는 대류항 $U\,\partial C/\partial z$와 분산항 $D_a\,\partial^2 C/\partial z^2$로 이루어진다. 분산 계수 $D_a$는 분자 확산 계수와 달리 속도, 관 지름, 충전물에 따라 달라지는 유효 계수이다. 길이 $L$과 속도 $U$로 무차원화하면 매개변수는 Peclet 수 $\mathrm{Pe}_r=UL/D_a$ 하나가 된다.The dispersion model adds a diffusion-like mixing term to the axial flow of a PFR. The tracer balance has a convection term $U\,\partial C/\partial z$ and a dispersion term $D_a\,\partial^2 C/\partial z^2$. Unlike the molecular diffusivity, the dispersion coefficient $D_a$ is an effective coefficient that depends on velocity, tube diameter, and packing. Scaling by length $L$ and velocity $U$ leaves a single parameter, the Peclet number $\mathrm{Pe}_r=UL/D_a$.
해는 입구와 출구에서 유체가 반응기 경계를 어떻게 지나는지, 즉 경계 조건에 따라 달라진다. 닫힌 계(closed-closed)는 입구와 출구 바깥이 플러그 흐름이어서 분산이 반응기 안에서만 일어난다. 이때 입구에서 Danckwerts 조건을 쓰는데, 입구 바로 안쪽에서 농도가 $C_0$보다 낮아지는 불연속이 생기기 때문이다. 열린 계(open-open)는 경계 바깥에서도 같은 분산이 일어나서 농도가 연속이다.The solution depends on how fluid crosses the reactor boundaries, that is, on the boundary conditions. In a closed-closed vessel the flow outside the inlet and outlet is plug flow, so dispersion occurs only inside. The Danckwerts condition is used at the inlet because the concentration just inside is lower than $C_0$, a jump. In an open-open vessel the same dispersion also occurs outside the boundaries, so the concentration is continuous.
$\mathrm{Pe}_r$의 의미: 대류에 의한 이동 대비 분산에 의한 이동의 비이다. $\mathrm{Pe}_r\to\infty$는 플러그 흐름(PFR)이고 $\mathrm{Pe}_r\to0$는 완전 혼합이다.Meaning of $\mathrm{Pe}_r$: the ratio of convective transport to dispersive transport. $\mathrm{Pe}_r\to\infty$ is a PFR and $\mathrm{Pe}_r\to0$ is complete mixing (CSTR-like).
Peclet 수 두 가지: 길이 기준 $\mathrm{Pe}_r=UL/D_a$와 지름 기준 $\mathrm{Pe}_f=Ud_t/D_a$가 있으며 $\mathrm{Pe}_r=\mathrm{Pe}_f\,(L/d_t)$이다. 상관식은 $\mathrm{Pe}_f$로, 반응기 모형은 $\mathrm{Pe}_r$로 쓴다.Two Peclet numbers: the length-based $\mathrm{Pe}_r=UL/D_a$ and the diameter-based $\mathrm{Pe}_f=Ud_t/D_a$, with $\mathrm{Pe}_r=\mathrm{Pe}_f\,(L/d_t)$. Correlations give $\mathrm{Pe}_f$ and reactor models use $\mathrm{Pe}_r$.
분산이 작을 때: $\mathrm{Pe}_r$이 약 20보다 크면 닫힌 계와 열린 계의 분산이 모두 $\sigma_\Theta^2\approx2/\mathrm{Pe}_r$로 같아진다. 이 범위에서는 경계 조건을 구분할 필요가 없다.Small dispersion: for $\mathrm{Pe}_r$ above about 20, both closed and open variances approach $\sigma_\Theta^2\approx2/\mathrm{Pe}_r$, so the boundary condition no longer matters.
Section 18.4
분산이 있는 흐름의 전환율과 분산 계수Flow, Reaction, and Dispersion
반응이 있으면 정상 상태 농도식은 $\frac{1}{\mathrm{Pe}_r}\frac{d^2\Psi}{d\lambda^2}-\frac{d\Psi}{d\lambda}-\mathrm{Da}_1\Psi=0$이 된다. 여기서 $\mathrm{Da}_1=k\tau$는 1차 반응의 Damköhler 수이다. 닫힌 계의 Danckwerts 조건으로 풀면 출구 전환율을 해석식으로 얻는다. $\mathrm{Pe}_r$이 크면 PFR의 $1-e^{-\mathrm{Da}_1}$에 가까워지고, 작으면 CSTR의 값에 가까워진다.With reaction, the steady-state equation becomes $\frac{1}{\mathrm{Pe}_r}\frac{d^2\Psi}{d\lambda^2}-\frac{d\Psi}{d\lambda}-\mathrm{Da}_1\Psi=0$, where $\mathrm{Da}_1=k\tau$ is the first-order Damköhler number. Solving with the closed-closed Danckwerts conditions gives the exit conversion in closed form. It tends to the PFR value $1-e^{-\mathrm{Da}_1}$ for large $\mathrm{Pe}_r$ and toward the CSTR value for small $\mathrm{Pe}_r$.
Figure 18.2Peclet 수에 따른 추적자 펄스 퍼짐과 축 방향 농도 분포Tracer Pulse Spreading and Axial Concentration Profile vs Peclet Number
예측: $k\tau=2$인 1차 반응에서 $\mathrm{Pe}_r$을 2에서 키우면 출구 전환율은 어떻게 될까?Predict: for a first-order reaction with $k\tau=2$, what happens to the exit conversion as $\mathrm{Pe}_r$ is raised from 2?
목표: 그림 아래 막대의 핸들을 끌어 $\mathrm{Pe}_r$을 바꾸고, 출구 전환율 $X$를 0.83 이상으로 올리세요. PFR 값 0.865의 96%입니다.Goal: drag the handle on the bar below the figure to change $\mathrm{Pe}_r$ and raise the exit conversion $X$ to 0.83 or more, which is 96% of the PFR value of 0.865.
Pe_r—
전환율 X (분산 모형)X (dispersion)—
PFR / CSTR 전환율PFR / CSTR X—
RTD 분산 (닫힌 계)RTD variance (closed)—
위쪽 관의 펄스는 위치 $\lambda=\Theta$를 중심으로 폭 $\sqrt{2\Theta/\mathrm{Pe}_r}$로 퍼지는 가우스 분포이고, 아래 곡선은 Danckwerts 조건의 해를 식에서 직접 계산한 값이다. 입구에서 농도가 1보다 낮은 불연속이 보이며, $\mathrm{Pe}_r$이 작을수록 이 불연속이 커서 전환율이 낮다.The pulse in the upper tube is a Gaussian centered at $\lambda=\Theta$ with width $\sqrt{2\Theta/\mathrm{Pe}_r}$, and the lower curve is the Danckwerts solution evaluated directly from the equations. The concentration jump below 1 at the inlet is visible, and it grows as $\mathrm{Pe}_r$ falls, which lowers conversion.
분산 계수는 상관식으로 추정한다. 층류 관 흐름에서는 Aris와 Taylor가 속도 분포 때문에 생기는 분산을 $D_a=D_{AB}+U^2R^2/(48D_{AB})$로 구했다. 확산이 느릴수록($Sc$가 클수록) 분산이 오히려 커지는데, 반경 방향으로 섞이지 않은 채 축 방향 속도 차이가 쌓이기 때문이다. 난류에서는 $D_a/(Ud_t)$가 Reynolds 수와 Schmidt 수로 정리된 그림(Figure 18-11)에서 읽는다. 충전층에서는 입자 지름 $d_p$를 기준으로 하는 그림(Figure 18-12)에서 읽는다.The dispersion coefficient is estimated from correlations. For laminar pipe flow, Aris and Taylor obtained the dispersion caused by the velocity profile as $D_a=D_{AB}+U^2R^2/(48D_{AB})$. Slower diffusion (larger $Sc$) actually increases dispersion, because axial velocity differences accumulate without radial mixing. For turbulent flow, $D_a/(Ud_t)$ is read from the chart of Reynolds and Schmidt numbers (Figure 18-11). For packed beds it is read from the chart based on particle diameter $d_p$ (Figure 18-12).
Aris-Taylor 분산: 층류에서 $D^*=D_a/D_{AB}=1+Pe_{AB}^2/48$ 형태이며, $Pe_{AB}=Ud_t/(2D_{AB})$의 제곱에 비례해 커진다. 관이 충분히 길어야(Figure 18-10의 $L/d_t$ 조건) 성립한다.Aris-Taylor dispersion: in laminar flow $D^*=D_a/D_{AB}=1+Pe_{AB}^2/48$ with $Pe_{AB}=Ud_t/(2D_{AB})$, growing with the square of the Peclet number. It holds only for long enough tubes (the $L/d_t$ conditions of Figure 18-10).
실험으로 구하기: 추적자 펄스에서 $t_m$과 $\sigma^2$를 구하고, 닫힌 계 또는 열린 계의 $\sigma_\Theta^2$ 식에서 $\mathrm{Pe}_r$을 풀면 $D_a=UL/\mathrm{Pe}_r$이다. 18.8절에서 직접 해 본다.From an experiment: obtain $t_m$ and $\sigma^2$ from a tracer pulse, solve the closed or open $\sigma_\Theta^2$ equation for $\mathrm{Pe}_r$, and then $D_a=UL/\mathrm{Pe}_r$. Section 18.8 does this.
Figure 18.3관 흐름의 분산 계수 $D_a/(Ud_t)$와 Reynolds 수Pipe-Flow Dispersion Coefficient $D_a/(Ud_t)$ vs Reynolds Number
Reynolds 수 (log10)Reynolds number (log10)10000
Schmidt 수 (log10, 층류)Schmidt number (log10, laminar)1
관 길이비 $L/d_t$Tube length ratio $L/d_t$100
흐름 영역Regime—
D_a/(U d_t)—
Pe_r = (L/d_t)/(D_a/(U d_t))—
등가 탱크 수 $n=\mathrm{Pe}_r/2+1$Equivalent tanks $n=\mathrm{Pe}_r/2+1$—
층류 곡선은 위 Aris-Taylor 식을 $Re\,Sc$로 정리한 값이고, 난류 곡선은 Figure 18-11을 근사하는 Wen과 Fan 형태의 근사식이다. 책의 그림에서 읽은 값이 아니므로 설계에는 원본 그림으로 확인해야 한다. 난류에서는 $Sc$ 의존성을 무시했고, 2100부터 3000까지는 전이 영역이어서 곡선을 그리지 않았다.The laminar curve is the Aris-Taylor expression rewritten in $Re\,Sc$, and the turbulent curve is a Wen and Fan type fit approximating Figure 18-11. These are not values read from the book's chart, so check the original figure for design. The $Sc$ dependence is ignored in turbulent flow, and 2100 to 3000 is the transition region where no curve is drawn.
Section 18.5
탱크 직렬 모형과 분산 모형의 비교Tanks-in-Series Model versus Dispersion Model
두 모형은 모두 RTD의 분산으로 매개변수를 정하고, 1차 반응에서는 계산 난이도가 같다. 1차가 아닌 반응이나 복합 반응에서는 T-I-S 모형이 탱크를 차례로 풀기만 하면 되어 수학적으로 쉽다. 분산 모형은 2계 미분방정식을 수치로 풀어야 한다.Both models fix their parameter from the variance of the RTD, and for first-order reactions they are equally easy. For other reaction orders and multiple reactions the T-I-S model only needs the tanks solved one after another, which is mathematically easier. The dispersion model requires a numerical solution of a second-order differential equation.
두 모형의 분산이 같아지는 조건에서 탱크 수와 Peclet 수가 연결된다. Peclet 수가 클 때 $\sigma_\Theta^2\approx2/\mathrm{Pe}_r$과 $\sigma_\Theta^2=1/n$을 같게 놓으면 아래 관계를 얻는다. 예제 18-1에서 $\mathrm{Pe}_r$로 구한 탱크 수 4.75는 T-I-S로 구한 4.35와 가깝다. 그래서 1차가 아닌 반응에서는 $n=4$와 $n=5$ 두 경우를 풀어 전환율의 범위를 잡는다.The two parameters are linked by equating the variances. At large Peclet number, setting $\sigma_\Theta^2\approx2/\mathrm{Pe}_r$ equal to $\sigma_\Theta^2=1/n$ gives the relation below. In Example 18-1 the tank number from $\mathrm{Pe}_r$ is 4.75, close to the 4.35 from the T-I-S analysis. For non-first-order reactions, therefore, solve both $n=4$ and $n=5$ to bracket the conversion.
Figure 18.41차 반응의 전환율: PFR, CSTR, 탱크 직렬, 분산 모형First-Order Conversion: PFR, CSTR, Tanks in Series, and Dispersion Model
탱크 수 $n$ (분산 모형은 $\mathrm{Pe}_r=2(n-1)$)Tanks $n$ (dispersion uses $\mathrm{Pe}_r=2(n-1)$)4
읽을 Damköhler 수 $k\tau$Damköhler number $k\tau$ to read2.0
X (T-I-S)X (T-I-S)—
X (분산)X (dispersion)—
두 모형의 차이Difference—
X (PFR / CSTR)—
T-I-S 식과 Danckwerts 닫힌 계 식을 이 페이지에서 직접 계산한 값이다. $n=4$일 때 두 모형의 전환율 차이가 0.2 퍼센트포인트 정도여서, 1차 반응에서는 어느 모형을 써도 같은 결과로 봐도 된다. $n=1$에서 분산 모형이 CSTR보다 약간 높은 것은 $\mathrm{Pe}_r\to0$에서도 입구의 경계 조건이 남기 때문이며, 이 구간에서는 닫힌 계의 관계식 $\mathrm{Pe}_r=2(n-1)$이 근사일 뿐이다.Both the T-I-S formula and the closed-closed Danckwerts formula are evaluated directly in this page. At $n=4$ the two conversions differ by about 0.2 percentage points, so for first-order reactions either model gives the same result. At $n=1$ the dispersion model sits slightly above the CSTR because the inlet boundary condition persists even as $\mathrm{Pe}_r\to0$; in that range $\mathrm{Pe}_r=2(n-1)$ is only an approximation.
Q2. 관형 반응기의 분산 모형에서 $\mathrm{Pe}_r=10$을 얻었다. 같은 RTD 분산을 주는 탱크 직렬 모형의 탱크 수는?Q2. A dispersion-model fit of a tubular reactor gives $\mathrm{Pe}_r=10$. How many tanks in series give the same RTD variance?
$n=\mathrm{Pe}_r/2+1=10/2+1=6$이다. $\mathrm{Pe}_r=2(n-1)$에서 1을 빠뜨리고$n=\mathrm{Pe}_r/2=5$로 쓰기 쉽다. 이 관계는 $\mathrm{Pe}_r$이 클 때의 근사이므로 $\mathrm{Pe}_r$이 작은 구간에서는 오차가 커진다.$n=\mathrm{Pe}_r/2+1=10/2+1=6$. It is easy to drop the 1 in $\mathrm{Pe}_r=2(n-1)$ and write $n=\mathrm{Pe}_r/2=5$. The relation is an approximation for large $\mathrm{Pe}_r$, so the error grows when $\mathrm{Pe}_r$ is small.
Section 18.7
이상 반응기 조합으로 만드는 이매개변수 모형Two-Parameter Models: Combinations of Ideal Reactors
매개변수가 둘인 모형은 이상 반응기를 병렬과 직렬로 조합한 것이다. 대표적인 모형은 바이패스와 데드 볼륨이 있는 CSTR 모형이다. 전체 부피 $V$ 중 $V_D$는 정체 영역이고, 전체 유량 $v_0$ 중 $v_b$는 반응기를 지나지 않고 출구로 간다. 활성 CSTR의 부피는 $V_s=V-V_D$, 유량은 $v_s=v_0-v_b$이다.Two-parameter models combine ideal reactors in parallel and in series. A representative model is a CSTR with a bypass and a dead volume. Of the total volume $V$, the volume $V_D$ is stagnant, and of the total flow $v_0$, the flow $v_b$ goes to the outlet without passing through the reactor. The active CSTR has volume $V_s=V-V_D$ and flow $v_s=v_0-v_b$.
두 매개변수를 바이패스 분율 $b=v_b/v_0$와 데드 볼륨 분율 $d=V_D/V$로 쓴다. 이 페이지가 정한 표기이며, 교재는 활성 부피 분율과 활성 유량 분율로 같은 내용을 나타낸다. 활성 탱크의 공간 시간은 $\tau_s=V_s/v_s=\tau(1-d)/(1-b)$이다. 추적자 펄스에 대한 출구 신호는 바이패스한 비율 $b$가 $t=0$에 delta 함수로 나오고, 나머지가 활성 CSTR의 지수 감쇠로 나오는 합이다.The textbook writes the two parameters as $\alpha=V_s/V$ (active volume fraction) and $\beta=v_s/v_0$; the equations below are rewritten with the bypass fraction $b=v_b/v_0=1-\beta$ and the dead-volume fraction $d=V_D/V=1-\alpha$. The active tank has space time $\tau_s=V_s/v_s=\tau(1-d)/(1-b)$. For a tracer pulse the outlet signal is the sum of a delta function at $t=0$ from the bypassed share and the exponential decay of the active CSTR.
이 식은 측정한 RTD에서 두 가지를 직접 읽게 한다. $t=0$ 직후의 신호가 바이패스 분율 $b$를 주고, 지수 감쇠의 시간 상수가 $\tau_s$를 주어 $d=1-\tau_s(1-b)/\tau$로 데드 볼륨 분율을 얻는다. 다른 조합으로는 PFR 다음에 CSTR이 이어지는 직렬 모형이 있고, 이때 CSTR이 차지하는 부피 분율이 하나의 매개변수이다. 교환이 있는 모형(정체 영역과 활성 영역 사이에 물질이 오가는 모형)은 매개변수가 하나 더 필요하다.From a measured RTD this equation allows two direct readings. The signal just after $t=0$ gives the bypass fraction $b$, and the time constant of the exponential decay gives $\tau_s$, hence the dead-volume fraction $d=1-\tau_s(1-b)/\tau$. Another combination puts a PFR and a CSTR in series with the CSTR volume fraction as the single parameter. Models with exchange (material moving between the stagnant and active zones) need one more parameter.
바이패스의 증거: 펄스를 넣자마자 출구에서 추적자가 나온다. 총량의 $b$가 $t=0$에 나온다.Evidence of bypassing: tracer appears at the outlet right after the pulse; a share $b$ of the total leaves at $t=0$.
데드 볼륨의 증거: 평균 체류 시간이 $V/v_0$보다 짧게 측정된다. 유체가 정체 영역을 쓰지 않으므로 같은 유량이 더 작은 부피를 지나간다.Evidence of a dead volume: the measured mean residence time is shorter than $V/v_0$, because the same flow passes through a smaller volume.
Figure 18.5바이패스와 데드 볼륨이 있는 CSTR의 RTD 맞추기Fitting the RTD of a CSTR with Bypass and Dead Volume
예측: 빨간 측정 자료에는 $t=0$에 막대가 있다. 이것은 어느 요인 때문일까?Predict: the red measured data has a bar at $t=0$. Which cause produces it?
목표: 파란 핸들 두 개를 끌어 막대 높이(바이패스 분율 $b$)와 감쇠 시간 $\tau_s$(데드 볼륨 분율 $d$)를 정하고, 측정 자료와의 잔차 $R$을 0.03 이하로 만드세요.Goal: drag the two blue handles to set the bar height (bypass fraction $b$) and the decay time $\tau_s$ (dead-volume fraction $d$) until the residual $R$ against the measured data is 0.03 or less.
바이패스 분율 bBypass fraction b—
데드 볼륨 분율 dDead-volume fraction d—
tau_s / tau—
잔차 RResidual R—
측정 자료는 이 페이지가 감춘 값으로 만든 모의 자료에 4% 크기의 결정론적 잡음을 더한 것이며 교재의 실측값이 아니다. 잔차는 연속 부분의 면적 차이 $\int|E_{model}-E_{meas}|d\Theta$에 막대 높이 차이를 더한 값이다. 위쪽 그림의 점은 이 계의 추적자 입자로, 바이패스 입자는 곧바로 나가고 활성 영역 입자는 지수 분포의 시간 뒤에 나간다.The measured data is simulated from values hidden in this page plus 4% deterministic noise, not a measurement from the textbook. The residual is the area mismatch of the continuous part $\int|E_{model}-E_{meas}|d\Theta$ plus the bar-height mismatch. In the schematic above, the dots are tracer particles: bypassed ones leave at once and active-zone ones leave after an exponentially distributed time.
Q3. 부피 100 L인 반응기에 유량 10 L/min을 흘린다. 데드 볼륨이 20 L이고 유량의 10%가 바이패스한다. 활성 CSTR의 공간 시간 $\tau_s$는?Q3. A 100 L reactor is fed at 10 L/min. The dead volume is 20 L and 10% of the flow bypasses. What is the space time $\tau_s$ of the active CSTR?
$V_s=100-20=80$ L, $v_s=10(1-0.1)=9$ L/min이므로 $\tau_s=80/9=8.9$ min이다. 데드 볼륨만 고려하면 8 min, 바이패스만 고려하면 11.1 min이다. 두 효과는 서로 반대 방향이어서 함께 있으면 일부가 서로 상쇄된다.$V_s=100-20=80$ L and $v_s=10(1-0.1)=9$ L/min, so $\tau_s=80/9=8.9$ min. With only the dead volume it would be 8 min, and with only the bypass 11.1 min. The two effects act in opposite directions, so together they partly cancel.
Section 18.8
추적자 자료에서 모형 매개변수 구하기Determining Model Parameters from Tracer Data
매개변수를 구하는 순서는 모형과 관계없이 같다. 출구 농도 $C(t)$를 적분으로 규격화해 $E(t)$를 만들고, 평균 체류 시간과 분산을 구한다. 그다음 모형의 분산식에 대입한다. 소프트웨어(Polymath, MATLAB, Python)는 $C(t)$에 모형 곡선을 직접 최소 제곱으로 맞추는 방법도 제공한다.The procedure is the same for every model. Normalize the outlet concentration $C(t)$ by its integral to obtain $E(t)$, then compute the mean residence time and the variance, and substitute them into the model's variance equation. Software (Polymath, MATLAB, Python) can also fit the model curve to $C(t)$ directly by least squares.
분산은 꼬리 부분의 자료에 가장 민감하다. $(t-t_m)^2$ 가중치 때문에 멀리 있는 작은 농도가 분산에 크게 기여한다. 측정이 너무 일찍 끝나면 분산이 작게 계산되어 $n$이 크게 나오고, 잡음이 있으면 반대 방향의 오차도 생긴다. 따라서 꼬리를 충분히 길게 측정하고, 모형 곡선과 자료를 겹쳐 눈으로도 확인해야 한다.The variance is most sensitive to the tail data. Because of the $(t-t_m)^2$ weight, small concentrations far out contribute strongly. If the measurement ends too early the variance comes out small and $n$ large, and noise adds errors in the other direction. Measure the tail long enough and always overlay the model curve on the data.
Figure 18.6추적자 펄스 자료에서 $n$과 $\mathrm{Pe}_r$ 구하기Obtaining $n$ and $\mathrm{Pe}_r$ from Tracer Pulse Data
측정 잡음 (%)Measurement noise (%)3
측정 종료 시간 (min)End of measurement (min)40
t_m (min)—
sigma^2 / t_m^2—
탱크 수 nTanks n—
Pe_r (열린 계 / 닫힌 계)Pe_r (open / closed)—
자료는 예제 18-1의 결과($t_m\approx10$ min, $n=4.35$)에 맞춰 이 페이지에서 만든 모의 값이며, 교재 표의 숫자가 아니다. 종료 시간을 14 min 쪽으로 줄이면 꼬리가 잘려 분산이 작아지고 $n$이 4.35보다 크게 나오므로, 같은 자료도 측정을 일찍 끝내면 PFR에 더 가까운 반응기로 잘못 판단한다.The data is simulated in this page to match the result of Example 18-1 ($t_m\approx10$ min, $n=4.35$) and is not a table from the textbook. Moving the end time toward 14 min cuts the tail, shrinks the variance, and gives $n$ above 4.35, so the same data mistakes the reactor for one closer to a PFR when the measurement stops early.
What If?
만약에?What If?
만약 2차 반응에서 같은 RTD로 T-I-S와 분산 모형을 쓴다면?What if a second-order reaction is computed with T-I-S and with the dispersion model for the same RTD?
클릭하여 확인 →Click to reveal →
두 모형은 같은 분산을 가지지만 RTD의 모양은 다르므로 전환율이 조금 다를 수 있다. 2차 반응은 분포가 넓을수록 전환율이 낮아진다. 그래서 T-I-S 모형에서 가까운 정수 탱크 수 두 개를 풀어 범위를 잡고, 분산 모형은 수치로 풀어 비교하는 것이 안전하다.The two models have the same variance but different RTD shapes, so conversions can differ slightly. A second-order reaction loses conversion as the distribution widens. It is safer to solve the T-I-S model for the two nearest integer tank numbers to bracket the answer and compare with a numerical dispersion solution.
만약 유량을 2배로 올리면 층류 관 반응기의 $\mathrm{Pe}_r$은?What if the flow rate is doubled in a laminar tubular reactor: what happens to $\mathrm{Pe}_r$?
클릭하여 확인 →Click to reveal →
층류에서 $D_a\approx U^2R^2/(48D_{AB})$이므로 $D_a$는 $U^2$에 비례한다. $\mathrm{Pe}_r=UL/D_a\propto1/U$이므로 유량을 2배로 올리면 $\mathrm{Pe}_r$은 절반으로 줄어든다. 빠르게 흘릴수록 PFR에 가까워질 것 같지만, 확산이 반경 방향 속도 차이를 줄이지 못해서 축 방향 분산이 더 크게 늘어난다.In laminar flow $D_a\approx U^2R^2/(48D_{AB})$, so $D_a\propto U^2$ and $\mathrm{Pe}_r=UL/D_a\propto1/U$. Doubling the flow halves $\mathrm{Pe}_r$. Faster flow seems closer to a PFR, but diffusion cannot even out the radial velocity differences in time, so axial dispersion grows more.
만약 RTD에 바이패스와 데드 볼륨이 모두 있는데 T-I-S 모형만 쓴다면?What if the RTD has both bypass and dead volume but only the T-I-S model is used?
클릭하여 확인 →Click to reveal →
분산은 맞출 수 있지만 모양을 설명하지 못한다. 바이패스는 $t=0$ 부근의 빠른 신호를 만들고 T-I-S 곡선은 그 구간에서 0이므로, 모형이 반응하지 않고 나가는 유체의 비율을 놓친다. 그 결과 전환율을 실제보다 높게 예측한다. 이 경우 18.7절의 이매개변수 모형이 필요하다.The variance can be matched but the shape cannot be explained. Bypassing makes an early signal near $t=0$ where the T-I-S curve is zero, so the model misses the share that leaves unreacted and predicts too high a conversion. A two-parameter model of Section 18.7 is needed.
Key Takeaways
01
분산에서 모형 매개변수로From Variance to Model Parameter
T-I-S 모형은 $n=1/\sigma_\Theta^2$, 분산 모형은 $\sigma_\Theta^2$ 식에서 $\mathrm{Pe}_r$을 풀어 구한다. 둘 다 추적자 자료의 평균과 분산이 입력이다.The T-I-S model gives $n=1/\sigma_\Theta^2$ and the dispersion model gives $\mathrm{Pe}_r$ by solving the $\sigma_\Theta^2$ equation. Both take the mean and variance of the tracer data as input.
02
경계 조건과 Peclet 수의 크기Boundary Conditions and the Size of Pe
닫힌 계는 Danckwerts 조건을 쓴다. $\mathrm{Pe}_r$이 약 20보다 크면 열린 계와 닫힌 계의 차이가 사라지고, 전환율은 PFR 값에 가까워진다.A closed vessel uses the Danckwerts conditions. Above $\mathrm{Pe}_r$ of about 20 the open and closed cases coincide and the conversion approaches the PFR value.
03
두 모형의 연결Linking the Two Models
$\mathrm{Pe}_r=2(n-1)$이므로 1차 반응에서는 두 모형의 전환율이 거의 같다. 1차가 아닌 반응은 T-I-S가 풀기 쉽고, 정수 탱크 수 두 개로 범위를 잡는다.With $\mathrm{Pe}_r=2(n-1)$ the two models give almost the same first-order conversion. For other orders T-I-S is easier to solve, and two integer tank numbers bracket the answer.
04
이매개변수 모형과 자료의 질Two-Parameter Models and Data Quality
$t=0$ 근처 신호는 바이패스, 지수 감쇠의 시간 상수는 활성 부피를 알려 준다. 분산은 꼬리에 민감하므로 측정을 충분히 길게 해야 한다.The signal near $t=0$ shows bypassing and the decay time constant shows the active volume. The variance is sensitive to the tail, so measure long enough.