반응기의 체류 시간 분포(RTD)Residence Time Distributions of Chemical Reactors
Fogler, Elements of Chemical Reaction Engineering, Chapter 16. 추적자를 주입하고 그림을 끌어 움직이면 유출 곡선 $E(t)$가 실시간으로 바뀝니다.Fogler, Elements of Chemical Reaction Engineering, Chapter 16. Inject a tracer and drag the figures to watch the outlet curve $E(t)$ respond in real time.
비이상 반응기의 일반적 특성General Considerations of Nonideal Reactors
지금까지 설계한 PFR과 CSTR은 흐름이 이상적이라고 가정했다. PFR에서는 모든 분자가 같은 시간 동안 반응기에 머물고, CSTR에서는 입구에서 들어온 유체가 즉시 완전히 섞인다. 실제 반응기는 이 가정에서 벗어난다. 충전층에서는 유체가 저항이 작은 길로 몰려 흐르는 채널링이 생기고, 교반 탱크에서는 입구 유체가 곧바로 출구로 나가는 바이패스와 거의 섞이지 않는 정체 영역(dead zone)이 생긴다.The PFR and CSTR designed so far assumed ideal flow: in a PFR every molecule stays the same time, and in a CSTR entering fluid is mixed completely at once. Real reactors deviate. Packed beds show channeling along paths of low resistance, and stirred tanks show bypassing, where inlet fluid leaves almost immediately, and dead zones that are barely mixed.
유체 요소마다 반응기 안에 머무는 시간이 다르기 때문에, 체류 시간의 분포를 알면 반응기 안의 흐름이 이상적인지 판단할 수 있다. 분포는 출구 흐름에서 체류 시간이 $t$와 $t+dt$ 사이인 유체의 분율 $E(t)\,dt$로 정의한다. 이상 반응기의 평균 체류 시간은 공간 시간 $\tau=V/v_0$와 같고, 비이상 반응기에서는 이 값과 달라질 수 있다.Because each fluid element spends a different time in the reactor, the distribution of residence times shows whether the flow is ideal. It is defined as the fraction $E(t)\,dt$ of the exit stream whose residence time lies between $t$ and $t+dt$. For an ideal reactor the mean residence time equals the space time $\tau=V/v_0$; for a nonideal one it can differ.
RTD는 반응기마다 하나로 정해지지만, 같은 RTD를 갖는 반응기가 여럿일 수 있다. RTD는 체류 시간의 분포만 알려 주고 분자 수준의 섞임 정도는 알려 주지 않기 때문이다. 이 장은 RTD를 측정하는 방법, RTD를 숫자로 요약하는 방법, 이상 반응기의 RTD, 그리고 RTD로 바이패스와 정체 부피를 진단하는 방법을 순서대로 다룬다.A reactor has one RTD, but several different reactors can share the same RTD, because the RTD describes the distribution of times and not the degree of molecular mixing. This chapter covers how to measure the RTD, how to summarize it numerically, the RTDs of ideal reactors, and how to diagnose bypassing and dead volume from it.
$$\tau=\frac{V}{v_0},\qquad E(t)\,dt=\text{fraction of exit stream aged between }t\text{ and }t+dt,\qquad \int_0^\infty E(t)\,dt=1$$
채널링과 바이패스: 유체 일부가 반응기를 짧은 경로로 지나 평균보다 훨씬 일찍 나간다. E(t)에서 작은 $t$ 쪽에 봉우리로 나타난다.Channeling and bypassing: part of the fluid takes a short path and leaves much earlier than average. It appears in $E(t)$ as a peak at small $t$.
정체 영역과 정체 부피: 흐름에 거의 참여하지 않는 부피 $V_D$이다. 유효 부피가 $V-V_D$로 줄어 평균 체류 시간이 $\tau$보다 짧아진다.Dead zones and dead volume: a volume $V_D$ that hardly takes part in the flow. The effective volume falls to $V-V_D$, so the mean residence time becomes shorter than $\tau$.
RTD가 알려 주지 않는 것: 같은 RTD라도 섞이는 시점(early mixing 또는 late mixing)이 다르면 비선형 반응의 전환율이 달라진다(16.5절).What the RTD does not tell: with the same RTD, a different moment of mixing (early or late mixing) changes the conversion of a nonlinear reaction (Section 16.5).
Section 16.2
RTD의 측정: 추적자 펄스 입력과 계단 입력Measurement of the RTD: Pulse and Step Tracer Inputs
RTD는 추적자(tracer)를 입구에 주입하고 출구 농도를 시간에 따라 재서 얻는다. 추적자는 반응하지 않고, 검출이 쉽고, 유체와 물성이 비슷하며, 벽에 흡착하지 않아야 한다. 염료, 방사성 동위원소, 전해질 용액이 흔히 쓰인다. 입력 방식은 두 가지이다. 펄스 입력은 추적자 $N_0$를 짧은 시간에 한꺼번에 넣고, 계단 입력은 일정한 농도 $C_0$의 추적자를 $t=0$부터 계속 넣는다.The RTD is obtained by injecting a tracer at the inlet and measuring the outlet concentration over time. The tracer must be nonreactive, easy to detect, similar to the fluid in physical properties, and must not adsorb on the walls. Dyes, radioactive isotopes, and electrolyte solutions are common. There are two inputs: a pulse injects an amount $N_0$ of tracer at once, and a step feeds tracer at constant concentration $C_0$ continuously from $t=0$.
펄스 입력에서는 $C(t)$를 출구 농도 곡선의 면적 $A$로 나누어 $E(t)$를 얻는다. 계단 입력에서는 출구 농도를 $C_0$로 나눈 값이 바로 $F(t)$이고, $F(t)$를 시간으로 미분하면 $E(t)$가 된다. 두 방법은 같은 RTD를 준다. 펄스는 곡선을 미분 없이 곧바로 얻는 대신 짧은 시간에 정확한 양을 넣어야 하고, 계단은 연속 공급이 쉬운 대신 미분에서 오차가 커진다.For a pulse, dividing the outlet curve $C(t)$ by its area $A$ gives $E(t)$. For a step, the outlet concentration divided by $C_0$ is directly $F(t)$, and differentiating $F(t)$ gives $E(t)$. Both give the same RTD. The pulse gives the curve without differentiation but needs an exact quantity injected quickly; the step is easy to feed continuously but amplifies error on differentiation.
펄스 입력: $C(t)$는 입력한 추적자의 몰 수 $N_0=v_0\int_0^\infty C\,dt$를 보존한다. 측정한 면적이 $N_0/v_0$와 다르면 추적자가 새거나 흡착한 것이다.Pulse input: $C(t)$ conserves the injected moles $N_0=v_0\int_0^\infty C\,dt$. If the measured area differs from $N_0/v_0$, tracer was lost or adsorbed.
계단 입력: $F(t)$는 0에서 1까지 단조 증가하는 누적 분포이다. 출구에서 $F=0.5$가 되는 시간이 중앙 체류 시간이다.Step input: $F(t)$ is a cumulative distribution rising monotonically from 0 to 1. The time at which $F=0.5$ at the outlet is the median residence time.
Figure 16.1반응기 종류별 추적자 펄스 응답 측정Tracer Pulse Response of Different Reactor Types
예측: $\tau=10$ min인 CSTR 입구에 펄스를 넣으면 출구 농도는 언제 가장 높을까?Predict: after a pulse enters a CSTR with $\tau=10$ min, when is the outlet concentration highest?
목표: 반응기 종류를 고르고 그림을 클릭해 펄스를 주입하세요. 다섯 종류를 모두 측정하면 달성입니다 (0/5).Goal: choose a reactor type and click the figure to inject a pulse. Measure all five types to finish (0/5).
평균 체류 시간 $t_m$ (min)Mean residence time $t_m$ (min)—
분산 $\sigma^2$ (min2)Variance $\sigma^2$ (min2)—
E(t) 면적Area under E(t)—
t_m / tau—
모든 반응기는 $V=100$ L, $v_0=10$ L/min이므로 $\tau=10$ min이다. 곡선은 이 절의 식으로 계산한 $E(t)$이고, 측정 창은 60 min이다(층류 반응기의 긴 꼬리가 일부 잘린다). PFR의 봉우리는 폭 0.12 min의 좁은 정규 분포로 그렸으며 이상적으로는 델타 함수이다. 바이패스는 유량의 25%, 정체 부피는 전체 부피의 25%로 정했다. CSTR은 주입 직후에 농도가 가장 높고 지수적으로 감소한다. 정체 부피가 있으면 $t_m$이 $\tau$보다 작아지고, 바이패스가 있으면 $t=0$ 근처에 봉우리가 생긴다.Every reactor has $V=100$ L and $v_0=10$ L/min, so $\tau=10$ min. The curves are $E(t)$ computed from this section's equations over a 60 min window (the long tail of the laminar reactor is partly cut). The PFR peak is drawn as a narrow normal distribution of width 0.12 min; ideally it is a delta function. The bypass is 25% of the flow and the dead volume is 25% of the volume. The CSTR is highest right after injection and decays exponentially. Dead volume makes $t_m$ smaller than $\tau$, and bypassing adds a peak near $t=0$.
Section 16.3
RTD의 특성: E(t), F(t), 평균과 분산Characteristics of the RTD: E(t), F(t), Mean, and Variance
$E(t)$를 적분한 누적 분포 $F(t)$는 반응기에 $t$보다 짧게 머문 유체의 분율이다. 따라서 $t_1$과 $t_2$ 사이에 나간 분율은 $F(t_2)-F(t_1)$이고, $t$보다 오래 머문 분율은 $1-F(t)$이다. 출구 농도 곡선은 검출기에서 이산적으로 얻으므로 예제 16-1처럼 곡선 면적을 수치로 구한 뒤 $E(t)=C(t)/A$로 규격화한다.The cumulative distribution $F(t)$, the integral of $E(t)$, is the fraction of fluid that stayed less than $t$ in the reactor. The fraction leaving between $t_1$ and $t_2$ is $F(t_2)-F(t_1)$, and the fraction that stayed longer than $t$ is $1-F(t)$. Since the outlet curve is measured at discrete times, Example 16-1 computes the area numerically and normalizes with $E(t)=C(t)/A$.
분포를 숫자로 요약할 때는 모멘트를 쓴다. 첫째 모멘트인 평균 체류 시간 $t_m$은 분포의 평균 위치이고, 평균 주위의 둘째 모멘트인 분산 $\sigma^2$은 분포가 퍼진 정도이다. 밀도가 변하지 않는 닫힌 계에서 $t_m=\tau$이다. $\sigma^2$이 0이면 PFR이고, $\sigma^2=\tau^2$이면 CSTR이다.Moments summarize the distribution numerically. The first moment, the mean residence time $t_m$, is the center of mass of the distribution, and the second moment about the mean, the variance $\sigma^2$, measures its spread. For a closed system of constant density, $t_m=\tau$. $\sigma^2=0$ is a PFR and $\sigma^2=\tau^2$ is a CSTR.
분산 $\sigma^2$: 단위가 시간의 제곱이다. $\sigma^2$이 클수록 분포가 넓고, 유체 요소마다 체류 시간의 차이가 크다.Variance $\sigma^2$: it has units of time squared. A larger $\sigma^2$ means a broader distribution and a larger spread of residence times among fluid elements.
무차원 시간 $\theta$: $t$를 $\tau$로 나누면 크기가 다른 반응기의 RTD를 같은 축에서 비교할 수 있다.Dimensionless time $\theta$: dividing $t$ by $\tau$ lets reactors of different sizes be compared on one axis.
Figure 16.2예제 16-1의 E(t)와 F(t), 시간 구간별 유출 분율E(t) and F(t) of Example 16-1 and the Fraction Leaving in a Time Window
구간 시작 $t_1$ (min)Window start $t_1$ (min)3.0
구간 끝 $t_2$ (min)Window end $t_2$ (min)6.0
C(t) 면적 A (g min/m3)Area under C(t), A (g min/m3)—
평균 체류 시간 $t_m$ (min)Mean residence time $t_m$ (min)—
분산 $\sigma^2$ (min2)Variance $\sigma^2$ (min2)—
구간에 나간 분율 F(t2) - F(t1)Fraction leaving in window F(t2) - F(t1)—
예제 16-1의 추적자 자료에서 $E(t)$ 값(0.02, 0.1, 0.16, 0.2, ...)은 교재 표에서 읽었고, $C(t)=51E(t)$로 환산해 C 값을 복원했다. 면적은 교재가 다항식 적합으로 51 g min/m3을 얻은 데 비해 이 페이지는 선형 보간한 곡선을 적분해 약 50.7을 얻는다. 곡선은 자료점 사이를 직선으로 잇고 $F$는 이 곡선을 수치 적분한다. 구간을 3과 6으로 두면 예제 16-2(d)의 질문(3 min에서 6 min 사이에 나간 분율)이 된다.The $E(t)$ values of Example 16-1 (0.02, 0.1, 0.16, 0.2, ...) were read from the textbook table and converted to $C(t)=51E(t)$ to restore the C values. The textbook obtains an area of 51 g min/m3 by polynomial fitting; this page integrates the linearly interpolated curve and gets about 50.7. The curve joins the data points with straight lines and $F$ is its numerical integral. Setting the window to 3 and 6 reproduces Example 16-2(d), the fraction leaving between 3 and 6 min.
Section 16.4
이상 반응기의 RTDRTD in Ideal Reactors
PFR에서는 모든 유체가 정확히 $\tau$ 동안 머무르므로 $E(t)$는 $t=\tau$에서 델타 함수이고 $F(t)$는 $\tau$에서 0에서 1로 바뀌는 계단 함수이다. 분산은 0이다. CSTR에 펄스를 넣으면 추적자는 곧바로 탱크 전체로 퍼지고, 유출 농도는 $e^{-t/\tau}$로 감소한다. 이때 $E(t)$의 지수 함수에서 $\sigma^2=\tau^2$이다.In a PFR every element stays exactly $\tau$, so $E(t)$ is a delta function at $t=\tau$ and $F(t)$ is a step from 0 to 1 at $\tau$. The variance is zero. When a pulse enters a CSTR, the tracer spreads through the whole tank at once and the outlet concentration decays as $e^{-t/\tau}$, giving $\sigma^2=\tau^2$ for the exponential $E(t)$.
층류 반응기(LFR)에서는 관 중심의 유체가 평균 속도의 두 배로 흐르므로 가장 빠른 유체가 $\tau/2$에 나온다. 그보다 이른 시간에는 추적자가 나오지 않고, 이후에는 $E(t)=\tau^2/(2t^3)$으로 감소한다. 관벽 근처의 느린 유체 때문에 꼬리가 길어서 분산 적분이 발산한다. 반경 방향 확산이 없는 이상적인 층류 모형의 결과이며, 실제로는 확산이 꼬리를 줄인다.In a laminar flow reactor (LFR), fluid at the tube center moves at twice the mean velocity, so the fastest fluid exits at $\tau/2$. Nothing exits earlier, and afterwards $E(t)=\tau^2/(2t^3)$ decreases. Slow fluid near the wall makes the tail long, and the variance integral diverges. This is the result of the ideal laminar model without radial diffusion; in practice diffusion shortens the tail.
CSTR의 63.2%: $t=\tau$에서 $F=1-e^{-1}=0.632$이다. 공간 시간만큼 지나도 유체의 36.8%는 아직 반응기 안에 있다.63.2% for a CSTR: at $t=\tau$, $F=1-e^{-1}=0.632$. After one space time, 36.8% of the fluid is still in the reactor.
세 반응기의 평균은 같다: PFR, CSTR, LFR 모두 $t_m=\tau$이다. 분산만 $0$, $\tau^2$, 발산으로 다르다.All three share the mean: PFR, CSTR, and LFR all have $t_m=\tau$. Only the variance differs: $0$, $\tau^2$, and divergent.
Figure 16.3PFR, CSTR, 층류 반응기의 E(t)와 F(t) 비교E(t) and F(t) of PFR, CSTR, and Laminar Flow Reactor
공간 시간 $\tau$ (min)Space time $\tau$ (min)10.0
CSTR에서 t = tau까지 나간 분율CSTR fraction out by t = tau—
층류에서 t = tau까지 나간 분율Laminar fraction out by t = tau—
CSTR 분산 (min2)CSTR variance (min2)—
층류 첫 유출 시간 (min)Laminar first exit time (min)—
곡선은 이 절의 식을 그대로 그린 것이고 측정값이 아니다. PFR의 델타 함수는 높이를 임의로 정한 수직선으로 나타냈다. $\tau$를 바꾸면 곡선은 시간 축으로 늘어나거나 줄어들지만 모양은 $\theta=t/\tau$에서 같다. $t=\tau$까지 CSTR은 63.2%, 층류 반응기는 75%만 나가고 PFR은 이 시점에서 전부 나간다.The curves plot this section's equations and are not measured data. The PFR delta function is drawn as a vertical line of arbitrary height. Changing $\tau$ stretches or shrinks the time axis, but the shapes are identical in $\theta=t/\tau$. By $t=\tau$ only 63.2% has left a CSTR and 75% a laminar reactor, while a PFR releases everything at that moment.
Section 16.5
PFR과 CSTR 직렬의 RTDPFR/CSTR Series RTD
실제 반응기를 PFR 부분과 CSTR 부분이 직렬로 이어진 것으로 모형화할 수 있다. 공간 시간이 $\tau_p$인 PFR과 $\tau_s$인 CSTR을 직렬로 두면 추적자는 PFR을 지나는 동안 모양이 변하지 않고 $\tau_p$만큼 늦게 나오며, 그 뒤 CSTR의 지수 감소가 시작된다. 평균 체류 시간은 $t_m=\tau_p+\tau_s$이고 분산은 CSTR 부분만으로 $\sigma^2=\tau_s^2$이다.A real reactor can be modeled as a PFR section and a CSTR section in series. With a PFR of space time $\tau_p$ and a CSTR of $\tau_s$, the tracer keeps its shape through the PFR and emerges delayed by $\tau_p$, after which the exponential decay of the CSTR begins. The mean residence time is $t_m=\tau_p+\tau_s$ and the variance comes from the CSTR part only, $\sigma^2=\tau_s^2$.
두 장치의 순서를 바꿔도 $E(t)$는 그대로이다. 그러나 비선형 반응의 전환율은 달라진다. 예제 16-3은 $\tau_s=\tau_p=1$ min, $k=1$ m3/(kmol min), $C_{A0}=1$ kmol/m3인 2차 반응을 다룬다. CSTR이 앞에 있으면(early mixing) $X=0.618$이고, PFR이 앞에 있으면(late mixing) $X=0.634$이다. 1차 반응에서는 두 순서의 전환율이 같다.Swapping the two units leaves $E(t)$ unchanged, but the conversion of a nonlinear reaction differs. Example 16-3 treats a second-order reaction with $\tau_s=\tau_p=1$ min, $k=1$ m3/(kmol min), and $C_{A0}=1$ kmol/m3. With the CSTR first (early mixing) $X=0.618$, and with the PFR first (late mixing) $X=0.634$. For a first-order reaction the two orders give the same conversion.
early mixing과 late mixing: 농도가 높을 때 PFR을 먼저 지나면 2차 반응이 빠르게 진행되므로 late mixing의 전환율이 더 높다. 이 전환율 차이는 반응 차수가 1보다 클수록 커진다.Early and late mixing: passing through the PFR first while the concentration is high lets a second-order reaction proceed quickly, so late mixing gives higher conversion. The difference grows as the reaction order exceeds 1.
RTD의 한계: 같은 $E(t)$에서 전환율이 다르다는 것은 RTD만으로 비선형 반응기의 성능을 정할 수 없다는 뜻이다. 섞임 모형을 따로 정해야 한다(17장과 18장).Limit of the RTD: different conversions at the same $E(t)$ mean the RTD alone cannot fix the performance of a reactor with nonlinear kinetics. A mixing model must be chosen separately (Chapters 17 and 18).
Figure 16.4PFR과 CSTR의 부피 분배에 따른 E(t)와 전환율E(t) and Conversion vs PFR/CSTR Volume Split
예측: 직렬로 이은 PFR과 CSTR의 순서를 바꾸면 E(t)는 어떻게 될까?Predict: if the PFR and CSTR in series swap places, what happens to E(t)?
목표: 막대 아래의 구분선을 끌어 PFR 비율을 바꾸고, 두 순서의 전환율 차이를 1.7 %p 이상으로 만드세요. 전체 $\tau=2$ min이고 2차 반응($k C_{A0}=1$ min-1)입니다.Goal: drag the divider under the bar to change the PFR fraction and make the conversion gap between the two orders at least 1.7 %p. Total $\tau=2$ min, second-order reaction ($k C_{A0}=1$ min-1).
tau_p (min)—
tau_s (min)—
평균 체류 시간 $t_m$ (min)Mean residence time $t_m$ (min)—
분산 $\sigma^2$ (min2)Variance $\sigma^2$ (min2)—
X, CSTR 먼저X, CSTR first—
X, PFR 먼저X, PFR first—
전환율 차이 (%p)Conversion gap (%p)—
전환율은 이 페이지에서 예제 16-3의 식으로 직접 계산한다. 구분선이 중앙(τp = τs = 1 min)이면 X는 0.618과 0.634로 교재와 같다. PFR 비율이 0이면 CSTR 하나(X = 0.5), 1이면 PFR 하나(X = 0.667)이고 순서는 의미가 없다. 두 순서의 차이는 PFR 비율 0.3 근처에서 가장 커서 약 1.9 %p이다. $E(t)$는 두 순서에서 같고 평균 체류 시간은 항상 2 min이다.Conversions are computed on this page with the equations of Example 16-3. With the divider at the center ($\tau_p=\tau_s=1$ min), X is 0.618 and 0.634, matching the textbook. A PFR fraction of 0 is a single CSTR (X = 0.5) and 1 a single PFR (X = 0.667), where order is meaningless. The gap between the two orders is largest near a PFR fraction of 0.3, about 1.9 %p. $E(t)$ is the same in both orders and the mean residence time is always 2 min.
Section 16.6
RTD를 이용한 진단과 문제 해결Diagnostics and Troubleshooting
설계한 대로 운전되지 않는 반응기는 RTD를 측정하여 원인을 찾는다. 이상적인 CSTR의 $E(t)$는 $t=0$에서 $1/\tau$로 시작하는 지수 곡선이다. 측정한 곡선에서 평균 체류 시간이 $V/v_0$보다 작으면 흐름에 참여하지 않는 정체 부피가 있다. $t=0$ 근처에 좁은 봉우리가 있고 그 뒤의 곡선이 더 천천히 감소하면 유체 일부가 바이패스한다.When a reactor does not perform as designed, the RTD helps find the cause. The ideal CSTR has an exponential $E(t)$ starting at $1/\tau$ at $t=0$. If the measured mean residence time is smaller than $V/v_0$, part of the volume takes no part in the flow. A narrow peak near $t=0$ followed by a slower decay means part of the fluid bypasses.
정체 부피 $V_D$를 가진 CSTR에서는 유효 부피가 $V-V_D$이므로 $t_m=(V-V_D)/v_0$이고, 이 식으로 $V_D=V-v_0t_m$을 얻는다. 유량 $v_b$가 바이패스하는 CSTR에서는 반응 부피로 $v_0-v_b$만 들어가므로 반응기 부분의 평균 체류 시간은 $\tau/(1-\beta)$로 늘어나고, $\beta=v_b/v_0$ 비율의 추적자가 지연 없이 나와 봉우리가 된다. 충전층에서 채널링과 정체 영역이 함께 있으면 두 특징이 한 곡선에 같이 나타난다.For a CSTR with dead volume $V_D$ the effective volume is $V-V_D$, so $t_m=(V-V_D)/v_0$, which gives $V_D=V-v_0t_m$. For a CSTR with a bypass flow $v_b$, only $v_0-v_b$ enters the reacting volume, so the mean residence time of the reactor part grows to $\tau/(1-\beta)$, and a fraction $\beta=v_b/v_0$ of the tracer leaves without delay as a peak. In a packed bed with both channeling and dead zones, both features appear in one curve.
평균 체류 시간으로 구별하기: 정체 부피가 있으면 $t_m<\tau$이다. 바이패스만 있으면 $t_m$이 $\tau$와 같다. 봉우리가 지연 없이 나가는 만큼 나머지가 더 오래 머물기 때문이다.Separating by the mean: with dead volume $t_m<\tau$. With bypass alone $t_m$ equals $\tau$, because the rest stays longer by as much as the peak leaves early.
곡선의 형태로 구별하기: 바이패스는 $t=0$ 근처의 봉우리로, 정체 부피는 처음 높이가 $1/\tau$보다 높고 더 빨리 감소하는 지수 곡선으로 나타난다.Separating by shape: bypass shows as a peak near $t=0$; dead volume shows as an exponential whose initial height exceeds $1/\tau$ and which decays faster.
Figure 16.5측정한 E(t)에서 결함 유형과 비율 찾기Identifying the Fault Type and Fraction from a Measured E(t)
예측: 빨간 곡선은 $\tau=10$ min인 CSTR에서 측정한 E(t)이다. 이 반응기의 결함은 바이패스일까, 정체 부피일까?Predict: the red curve is the E(t) measured in a CSTR with $\tau=10$ min. Is the fault a bypass or a dead volume?
목표: 유형을 고른 뒤 그림 아래 막대의 점을 끌어 파란 점선 모형이 빨간 곡선과 겹치게 하세요. 결함 비율을 3 %p 안에서 맞히면 달성입니다.Goal: choose the type, then drag the dot on the bar below the figure until the blue dashed model overlaps the red curve. Match the fault fraction within 3 %p.
측정한 $t_m$ (min)Measured $t_m$ (min)—
$\tau=V/v_0$ (min)$\tau=V/v_0$ (min)10.0
t_m / tau—
모형의 결함 비율Model fault fraction—
곡선 차이 (RMS)Curve gap (RMS)—
문제의 곡선은 이 절의 두 식으로 만든 가상 측정값이고 실제 실험 자료가 아니다. 결함 비율은 12%부터 40%까지에서 무작위로 정한다. 그림에서 위로 솟은 봉우리는 세로축을 0.2 min-1에서 잘랐다는 뜻이다. 바이패스에서는 $t_m$이 $\tau$ 근처에 머물고, 정체 부피에서는 $t_m=(1-V_D/V)\tau$로 비율이 바로 읽힌다. 충전층의 채널링도 같은 방식으로 이른 시간의 봉우리로 나타난다.The problem curve is a synthetic measurement built from the two equations of this section, not real experimental data. The fault fraction is drawn at random between 12% and 40%. A peak rising out of the frame means the vertical axis is cut at 0.2 min-1. With bypass $t_m$ stays near $\tau$, and with dead volume $t_m=(1-V_D/V)\tau$ gives the fraction directly. Channeling in a packed bed shows up the same way, as an early peak.
Self-Check
확인 문제Quiz
Q1. 펄스 입력으로 얻은 출구 농도 $C(t)$에서 $E(t)$를 얻으려면 $C(t)$를 무엇으로 나누는가?Q1. To obtain $E(t)$ from the outlet concentration $C(t)$ of a pulse input, what is $C(t)$ divided by?
$E(t)$는 면적이 1이 되도록 규격화한 분포이므로 $E(t)=C(t)/\int_0^\infty C\,dt$이다. 예제 16-1에서 면적은 약 51 g min/m3이다. $C_0$로 나누는 것은 계단 입력에서 $F(t)$를 얻을 때이다.$E(t)$ is normalized to unit area, so $E(t)=C(t)/\int_0^\infty C\,dt$. In Example 16-1 the area is about 51 g min/m3. Dividing by $C_0$ is for $F(t)$ from a step input.
Q2. 이상적인 CSTR에서 $t=\tau$가 지난 시점에 출구로 이미 나간 유체의 분율은?Q2. In an ideal CSTR, what fraction of the fluid has already left by $t=\tau$?
$F(\tau)=1-e^{-1}=0.632$이다. 36.8%는 아직 반응기 안에 있는 분율 $e^{-1}$이다. 평균 체류 시간이 $\tau$여도 절반이 넘는 63.2%가 평균보다 일찍 나가고, 일부는 훨씬 오래 머문다.$F(\tau)=1-e^{-1}=0.632$. The 36.8% is the fraction $e^{-1}$ still inside. Even though the mean residence time is $\tau$, 63.2%, more than half, leaves earlier than the mean while some stays much longer.
Q3. $V/v_0=10$ min인 CSTR에 펄스를 주입했더니 측정한 $t_m=7.5$ min이고 $E(t)$가 지수 곡선이었다. 정체 부피는 전체 부피의 몇 %인가?Q3. A pulse into a CSTR with $V/v_0=10$ min gives a measured $t_m=7.5$ min and an exponential $E(t)$. What percentage of the volume is dead?
$V_D/V=1-t_m/\tau=1-7.5/10=0.25$이다. 바이패스는 $t_m$을 $\tau$ 근처에 두고 $t=0$ 근처에 봉우리를 만든다. 지수 곡선이면서 $t_m<\tau$인 것은 정체 부피의 특징이다.$V_D/V=1-t_m/\tau=1-7.5/10=0.25$. Bypass keeps $t_m$ near $\tau$ and adds a peak near $t=0$. An exponential with $t_m<\tau$ is the signature of dead volume.
What If?
만약에?What If?
만약 반응이 1차 반응이라면 PFR과 CSTR의 순서를 바꿔도 전환율이 같을까?What if the reaction is first order: does swapping the PFR and CSTR change the conversion?
클릭하여 확인 →Click to reveal →
같다. 1차 반응은 속도가 농도에 선형이어서 섞이는 시점이 달라도 평균 속도가 변하지 않는다. 순서에 따라 전환율이 달라지는 것은 2차 이상의 비선형 반응이다. 그래서 1차 반응에서는 RTD만으로 전환율을 정할 수 있다.Yes. A first-order rate is linear in concentration, so the moment of mixing does not change the mean rate. Order matters only for nonlinear (second order and above) reactions. For first-order kinetics the RTD alone fixes the conversion.
만약 CSTR의 교반을 줄여 정체 영역이 커진다면 E(t)는 어떻게 될까?What if reduced stirring in a CSTR enlarges the dead zones: what happens to E(t)?
클릭하여 확인 →Click to reveal →
유효 부피가 줄어 $\tau'=\tau(1-V_D/V)$가 작아지므로 $E(0)=1/\tau'$이 올라가고 곡선이 더 빨리 감소한다. 같은 공급 유량에서 반응에 쓰이는 부피가 줄어 전환율이 떨어진다. 반면 $t_m$이 줄어드는 것을 측정하면 정체 부피를 계산할 수 있다.The effective volume shrinks, so $\tau'=\tau(1-V_D/V)$ falls, $E(0)=1/\tau'$ rises, and the curve decays faster. At the same feed rate less volume is used for reaction, so conversion drops. Conversely, measuring the decrease of $t_m$ lets you calculate the dead volume.
만약 층류 반응기에서 반경 방향 확산이 있다면 E(t)의 긴 꼬리는?What if there is radial diffusion in a laminar flow reactor: what happens to the long tail of E(t)?
클릭하여 확인 →Click to reveal →
확산이 느린 관벽 쪽 유체를 빠른 중심부로 옮겨 오래 머무는 유체가 줄어든다. 꼬리가 $t^{-3}$보다 빨리 감소하여 분산이 발산하지 않고 유한한 값을 가진다. 확산이 충분히 크면 층류 반응기는 PFR에 가까운 분포를 갖는다. 이 내용은 17장의 분산 모형에서 다룬다.Diffusion carries slow wall fluid toward the faster center, so less fluid stays long. The tail decays faster than $t^{-3}$, the variance no longer diverges, and it is finite. With enough diffusion a laminar reactor approaches PFR-like behavior. Chapter 17 treats this in the dispersion model.
Key Takeaways
01
추적자로 E(t)를 얻는다Tracers Give E(t)
펄스 응답 $C(t)$를 면적으로 나누면 $E(t)$이고, 계단 응답 $C/C_0$는 $F(t)$이며 미분하면 $E(t)$이다.Dividing the pulse response $C(t)$ by its area gives $E(t)$; the step response $C/C_0$ is $F(t)$, whose derivative is $E(t)$.
02
평균과 분산으로 요약Summary by Mean and Variance
$t_m$은 분포의 중심이고 $\sigma^2$은 퍼진 정도이다. PFR은 $\sigma^2=0$, CSTR은 $\sigma^2=\tau^2$이다.$t_m$ is the center and $\sigma^2$ the spread. A PFR has $\sigma^2=0$ and a CSTR has $\sigma^2=\tau^2$.
03
E(t)로 결함을 진단Diagnosis from E(t)
$t_m<\tau$이면 정체 부피($V_D=V-v_0t_m$)이고, $t=0$ 근처의 봉우리는 바이패스 또는 채널링이다.$t_m<\tau$ means dead volume ($V_D=V-v_0t_m$), and a peak near $t=0$ means bypassing or channeling.
04
RTD는 유일한 정보가 아니다The RTD Is Not the Whole Story
같은 $E(t)$를 가진 PFR과 CSTR 직렬도 순서에 따라 2차 반응의 전환율이 달라진다. 섞임 모형이 따로 필요하다.A PFR and CSTR in series with the same $E(t)$ still give different second-order conversions depending on order. A mixing model is also needed.