반응계의 물질전달 제한Mass Transfer Limitations in Reacting Systems
Fogler, Elements of Chemical Reaction Engineering, Chapter 14. 촉매 입자와 충전층을 끌어 움직이면 경계층과 전환율이 실시간으로 바뀐다.Fogler, Elements of Chemical Reaction Engineering, Chapter 14. Drag the catalyst particle and the packed bed and watch the boundary layer and conversion respond in real time.
Fick 법칙경계층과 kcSherwood 수충전층 물질전달 제한Robert the WorrierShrinking core
Section 14.1
확산의 기초: 몰 플럭스와 Fick 법칙Diffusion Fundamentals: Molar Flux and Fick's Law
촉매 반응에서 반응물은 유체 본체에서 촉매 표면까지 먼저 이동해야 한다. 이 이동이 느리면 표면 반응이 아무리 빨라도 전체 속도는 이동 속도로 정해진다. 입자 내부의 기공 확산은 15장에서 다루고, 이 장은 입자 바깥쪽 유체에서 일어나는 외부 물질전달을 다룬다.In a catalytic reaction the reactant must first travel from the bulk fluid to the catalyst surface. If that transport is slow, the overall rate is set by the transport no matter how fast the surface reaction is. Diffusion inside the pores is treated in Chapter 15; this chapter treats external mass transfer in the fluid outside the particle.
화학종 A의 몰 플럭스 $W_A$는 단위 면적과 단위 시간당 이동하는 몰 수이다. 이 플럭스는 농도 기울기에서 생기는 분자 확산 플럭스 $J_A$와 유체 전체가 움직여서 생기는 대류 플럭스 $B_A$의 합이다. 확산 플럭스는 Fick 법칙으로 쓴다. 기체의 확산도 $D_{AB}$는 $T^{1.75}/P$에 비례하고, 액체의 확산도는 기체보다 약 네 자릿수 작다.The molar flux $W_A$ of species A is the number of moles crossing unit area per unit time. It is the sum of the molecular diffusion flux $J_A$, which comes from a concentration gradient, and the bulk flow flux $B_A$, which comes from the motion of the whole fluid. The diffusive part follows Fick's law. The gas diffusivity $D_{AB}$ scales as $T^{1.75}/P$, and liquid diffusivities are about four orders of magnitude smaller than gas values.
확산 플럭스 $J_A$: 농도가 높은 쪽에서 낮은 쪽으로 향하며, 크기는 농도 기울기와 $D_{AB}$의 곱이다. 기체는 $10^{-5}$ m²/s 정도, 액체는 $10^{-9}$ m²/s 정도이다.Diffusive flux $J_A$: directed from high to low concentration, with magnitude equal to the gradient times $D_{AB}$. Gases are near $10^{-5}$ m²/s and liquids near $10^{-9}$ m²/s.
대류 플럭스 $B_A$: A의 몰분율 $y_A$에 총 몰 플럭스를 곱한 값이다. 총 몰 플럭스가 0이 아니면 확산이 없어도 A가 이동한다.Bulk flow flux $B_A$: the mole fraction $y_A$ times the total molar flux. When the total flux is not zero, A moves even without diffusion.
온도 보정 (예제 14-2): 298 K에서 $0.69\times10^{-4}$ m²/s인 히드라진과 헬륨의 확산도는 450 K에서 $(450/298)^{1.75}=2.06$배가 되어 $1.42\times10^{-4}$ m²/s이다.Temperature correction (Example 14-2): the hydrazine-helium diffusivity of $0.69\times10^{-4}$ m²/s at 298 K becomes $(450/298)^{1.75}=2.06$ times larger, $1.42\times10^{-4}$ m²/s, at 450 K.
A와 B 두 성분만 있는 좁은 막 안에서 A가 표면 쪽으로 가는 만큼 B가 반대로 나오면 $W_{Bz}=-W_{Az}$이고, 총 몰 플럭스가 0이므로 대류 항이 사라진다. 이때 $W_{Az}=J_{Az}$이며 정상 상태에서 농도는 막 두께 $\delta$에 걸쳐 직선으로 변한다. 이성분 계의 이 경우를 등몰 역방향 확산이라고 한다.In a thin film containing only A and B, if B leaves as fast as A arrives at the surface, then $W_{Bz}=-W_{Az}$ and the total flux is zero, so the bulk flow term disappears. Then $W_{Az}=J_{Az}$ and at steady state the concentration falls linearly across the film thickness $\delta$. This case of a binary system is called equimolar counterdiffusion.
반응식 $\mathrm{A}\rightarrow\mathrm{B}$에서 표면 반응이 한 몰의 A를 소비하면서 한 몰의 B를 내보내는 경우가 이에 해당한다. 직선 분포이므로 플럭스는 농도 차를 막 두께로 나눈 값에 $D_{AB}$를 곱하면 된다. 이 식에서 $D_{AB}/\delta$는 속도의 단위(m/s)를 가지며, 14.4절의 물질전달 계수 $k_c$가 된다.The reaction $\mathrm{A}\rightarrow\mathrm{B}$ is an example: the surface consumes one mole of A while releasing one mole of B. With a linear profile the flux is $D_{AB}$ times the concentration difference over the film thickness. The ratio $D_{AB}/\delta$ has units of velocity (m/s) and becomes the mass transfer coefficient $k_c$ of Section 14.4.
적용 조건: 두 성분의 몰 플럭스가 크기는 같고 방향이 반대이다. 반응에서 몰 수가 변하지 않는 기상 반응(예: 이성질화)이나 묽은 용액에서 근사적으로 성립한다.Conditions: the two molar fluxes are equal in size and opposite in direction. It holds for gas-phase reactions without a change in moles (for example isomerization) and approximately in dilute solutions.
직선 농도 분포: 플럭스가 위치에 관계없이 일정하므로 $dC_A/dz$도 일정하다. 14.3절의 그림에서 다른 경우와 비교한다.Linear profile: the flux is the same at every position, so $dC_A/dz$ is constant. Figure 14.1 in Section 14.3 compares it with the other case.
Section 14.3
정체 막을 통한 확산Diffusion Through a Stagnant Film
표면 반응이 A만 소비하고 생성물이 B가 아닌 다른 쪽으로 나가면 막 안의 B는 움직이지 않는다($W_{Bz}=0$). 그러면 $W_{Az}=J_{Az}+y_AW_{Az}$이므로 $W_{Az}=J_{Az}/(1-y_A)$이다. A가 이동하면서 만드는 대류가 A 자신의 이동을 돕는 경우이다.If the surface consumes A only and the product leaves some other way, B in the film does not move ($W_{Bz}=0$). Then $W_{Az}=J_{Az}+y_AW_{Az}$, so $W_{Az}=J_{Az}/(1-y_A)$. The bulk flow created by the moving A helps A itself move.
농도가 묽으면 $y_A\ll1$이므로 두 경우의 차이가 거의 없다. $y_A$가 커질수록 정체 막의 플럭스가 등몰 역방향 확산보다 커진다. 막 안의 $y_A$ 분포도 직선이 아니라 로그 형태가 된다. 그림 14.1에서 조성과 막 두께를 바꿔 두 경우를 비교한다.At low concentration $y_A\ll1$ the two cases barely differ. As $y_A$ grows, the stagnant film flux exceeds the equimolar counterdiffusion flux, and the $y_A$ profile in the film becomes logarithmic instead of linear. Figure 14.1 compares the two cases as composition and film thickness change.
정체 막 $W_A$ (mol/(m² s))Stagnant film $W_A$ (mol/(m² s))0
플럭스 비 (정체 막 / 등몰)Flux ratio (stagnant / equimolar)0
표면에서 $y_A=0$이고 $D_{AB}=1.42\times10^{-4}$ m²/s(예제 14-2의 히드라진과 헬륨, 450 K), $C_T=27.1$ mol/m³(1 atm)를 썼다. 비는 $-\ln(1-y_{A0})/y_{A0}$이므로 $y_{A0}$가 0에 가까우면 1이고, 0.9에서는 2.6이 된다. 묽은 계에서 등몰 역방향 확산 식을 쓰는 근거가 이 극한이다.Surface $y_A=0$, $D_{AB}=1.42\times10^{-4}$ m²/s (hydrazine-helium of Example 14-2 at 450 K), $C_T=27.1$ mol/m³ (1 atm). The ratio is $-\ln(1-y_{A0})/y_{A0}$: 1 as $y_{A0}\to0$ and 2.6 at 0.9. This limit is why the equimolar formula is used for dilute systems.
등몰 역방향 확산과 정체 막: 두 경우 모두 $W_A=kC$ 꼴로 정리되며 물질전달 계수 $k_c$를 정의할 수 있다. 차이는 조성이 높을 때만 나타난다.Equimolar and stagnant film: both reduce to the form $W_A=kC$ and allow a mass transfer coefficient $k_c$ to be defined. They differ only at high composition.
Section 14.4
물질전달 계수와 외부 물질전달 제한The Mass Transfer Coefficient and External Mass Transfer Limitation
고체 표면 가까이에서는 유체 속도가 0에 가까워져 경계층이 생기고, 반응물은 이 경계층 안에서 확산으로만 이동한다. 이 막의 유효 두께를 $\delta$라 하면 플럭스는 $W_A=k_c(C_{Ab}-C_{As})$이고 $k_c=D_{AB}/\delta$이다. 유속이 빠를수록 경계층이 얇아져 $k_c$가 커진다.Near a solid surface the fluid velocity falls toward zero and a boundary layer forms, in which the reactant moves by diffusion alone. If the effective thickness of this film is $\delta$, the flux is $W_A=k_c(C_{Ab}-C_{As})$ with $k_c=D_{AB}/\delta$. A faster flow makes the layer thinner and $k_c$ larger.
$k_c$는 무차원수의 상관식으로 구한다. Sherwood 수 $\mathrm{Sh}=k_cd_p/D_{AB}$는 입자 크기를 경계층 두께로 나눈 값에 해당하며, Reynolds 수 $\mathrm{Re}$와 Schmidt 수 $\mathrm{Sc}$의 함수이다. 단일 구에는 Frossling 상관식을, 충전층에는 Thoenes-Kramers 상관식을 쓴다. 두 식 모두 $\mathrm{Sh}\propto\mathrm{Re}^{1/2}\mathrm{Sc}^{1/3}$ 꼴이다.$k_c$ comes from dimensionless correlations. The Sherwood number $\mathrm{Sh}=k_cd_p/D_{AB}$ equals the particle size divided by the boundary layer thickness, and is a function of the Reynolds number $\mathrm{Re}$ and the Schmidt number $\mathrm{Sc}$. The Frossling correlation applies to a single sphere and the Thoenes-Kramers correlation to a packed bed. Both have the form $\mathrm{Sh}\propto\mathrm{Re}^{1/2}\mathrm{Sc}^{1/3}$.
Figure 14.2Reynolds 수에 따른 Sherwood 수 상관식 비교Sherwood Number Correlations Versus Reynolds Number
$\log_{10}\mathrm{Re}$$\log_{10}\mathrm{Re}$100
$\log_{10}\mathrm{Sc}$$\log_{10}\mathrm{Sc}$1.0
층 공극률 $\phi$Bed porosity $\phi$0.40
Sh, 단일 구 (Frossling)Sh, single sphere (Frossling)0
Sh, 충전층 (Thoenes-Kramers)Sh, packed bed (Thoenes-Kramers)0
Sh, 평판 층류Sh, laminar flat plate0
Re를 4배로 올릴 때 Sh 증가율 (Frossling)Sh gain for 4x Re (Frossling)0
식은 교재의 표 14-5와 식 14-65이며, 각 곡선은 이 식을 그대로 계산한 값이다. Thoenes-Kramers 식은 교재의 유효 범위(공극률 0.25부터 0.5, Re 40부터 4000, Sc 1부터 4000)를 벗어나도 곡선을 그렸다. Re가 크면 $\mathrm{Sh}\propto\mathrm{Re}^{1/2}$이므로 Re를 4배로 올려도 Sh는 2배에 못 미친다.The equations are Table 14-5 and Eq. 14-65 of the text, evaluated directly. The Thoenes-Kramers curve is drawn beyond the stated validity range (porosity 0.25 to 0.5, Re 40 to 4000, Sc 1 to 4000). At large Re, $\mathrm{Sh}\propto\mathrm{Re}^{1/2}$, so quadrupling Re raises Sh by less than a factor of 2.
촉매 구 하나에서 반응이 표면에서 순간적으로 일어나면 $C_{As}=0$이다. 예제 14-1은 지름 1 cm인 구가 액체 B 속에서 0.1 m/s로 놓여 있고, $\nu=5\times10^{-7}$ m²/s, $D_{AB}=10^{-10}$ m²/s, $C_{Ab}=1$ mol/dm³인 경우이다. 이때 $\mathrm{Re}=2000$, $\mathrm{Sc}=5000$이고 $\mathrm{Sh}=460.7$, $k_c=4.61\times10^{-6}$ m/s, $W_{Ar}=4.61\times10^{-3}$ mol/(m² s)이다.For a single catalyst sphere with an instantaneous surface reaction, $C_{As}=0$. Example 14-1 has a 1 cm sphere in liquid B at 0.1 m/s with $\nu=5\times10^{-7}$ m²/s, $D_{AB}=10^{-10}$ m²/s and $C_{Ab}=1$ mol/dm³. Then $\mathrm{Re}=2000$, $\mathrm{Sc}=5000$, $\mathrm{Sh}=460.7$, $k_c=4.61\times10^{-6}$ m/s and $W_{Ar}=4.61\times10^{-3}$ mol/(m² s).
표면 반응이 유한한 속도 $k_r$로 일어나면 표면 농도 $C_{As}$는 0이 아니다. 정상 상태에서 표면에 도착하는 양과 반응하는 양이 같으므로 두 저항이 직렬로 더해진다. $k_r\gg k_c$이면 물질전달이 속도를 정하고, $k_r\ll k_c$이면 표면 반응이 정한다. 그림 14.3에서 유속과 입자 지름을 바꿔 이 전환을 확인한다.When the surface reaction has a finite rate constant $k_r$, the surface concentration $C_{As}$ is not zero. At steady state the arrival rate equals the reaction rate, so the two resistances add in series. If $k_r\gg k_c$, mass transfer sets the rate; if $k_r\ll k_c$, the surface reaction sets it. Figure 14.3 shows this switch as velocity and particle diameter change.
Figure 14.3촉매 입자의 경계층과 관측 속도: 유속과 입자 지름 변화Boundary Layer and Observed Rate of a Catalyst Pellet: Velocity and Diameter
예측: 표면 반응이 매우 빠를 때 유속 $U$를 4배로 올리면 관측 속도는 몇 배가 될까?Predict: when the surface reaction is very fast, how many times does the observed rate rise if the velocity $U$ is quadrupled?
목표: 아래 두 막대의 점을 끌어 $U$와 $d_p$를 바꾸며 관측 속도를 측정하세요. 그림 오른쪽 아래에 점이 쌓입니다. 속도 변화를 보고 이 촉매 샘플이 반응 속도 제한인지, 물질전달 제한인지, 둘이 섞인 영역인지 고르세요. 샘플은 숨겨져 있으며 새 샘플 버튼으로 바꿀 수 있습니다.Goal: drag the dots on the two bars to change $U$ and $d_p$ and measure the observed rate. Points accumulate at the lower right. From the trend decide whether this catalyst sample is reaction-limited, mass-transfer-limited, or mixed. The sample is hidden; the new-sample button swaps it.
U (m/s)—
d_p (mm)—
k_c (m/s)—
경계층 두께 $\delta$ (mm)Boundary layer $\delta$ (mm)—
관측 속도 (mol/(m² s))Observed rate (mol/(m² s))—
측정한 점 수Points measured0
기체 조건은 $\nu=1.5\times10^{-5}$ m²/s, $D_{AB}=1.4\times10^{-5}$ m²/s이고 $k_c$는 Frossling 식, 경계층 두께는 $\delta=D_{AB}/k_c=d_p/\mathrm{Sh}$이다. 관측 속도는 $C_{Ab}=1$ mol/m³에서의 값이다. 반응 속도 제한이면 $U$를 올려도 속도가 거의 같고 입자 지름에도 둔감하지만, 물질전달 제한이면 $U^{1/2}$에 비례해 오르고 $d_p$가 커지면 내려간다. 답을 고르면 표면 농도 분포가 나타난다.Gas conditions are $\nu=1.5\times10^{-5}$ m²/s and $D_{AB}=1.4\times10^{-5}$ m²/s; $k_c$ is from the Frossling equation and the boundary layer thickness is $\delta=D_{AB}/k_c=d_p/\mathrm{Sh}$. The rate is for $C_{Ab}=1$ mol/m³. A reaction-limited sample shows almost no change with $U$ or $d_p$; a mass-transfer-limited one rises as $U^{1/2}$ and falls as $d_p$ grows. Choosing an answer reveals the surface concentration profile.
충전층에서는 유체가 층을 지나면서 반응물이 촉매 표면으로 이동해 소비된다. 외부 물질전달이 속도를 정하면 $C_{As}\approx0$이므로 축 방향 몰 수지는 $U\,dC_A/dz=-k_ca_cC_A$이다. 여기서 $a_c=6(1-\phi)/d_p$는 층 부피당 외부 표면적이다. 적분하면 전환율이 $k_c$, $a_c$, $U$, 층 길이 $L$ 네 가지로만 정해진다.In a packed bed the fluid passes through while the reactant moves to the catalyst surface and is consumed. If external mass transfer controls, $C_{As}\approx0$ and the axial mole balance is $U\,dC_A/dz=-k_ca_cC_A$, where $a_c=6(1-\phi)/d_p$ is the external surface area per bed volume. Integration shows that conversion is set by $k_c$, $a_c$, $U$ and the bed length $L$ alone.
예제 14-2는 2% 히드라진과 98% 헬륨 혼합 기체가 지름 0.25 cm, 길이 0.5 cm인 원통형 촉매 위를 150 m/s, 450 K로 지나는 경우이다. 부피 기준 평균 지름은 3.61 mm이고 $a_c=998$ m²/m³이다. 층 길이 0.05 m에서의 전환율이 그림 14.4의 출발점이다.Example 14-2 passes a 2% hydrazine, 98% helium gas over cylindrical pellets (0.25 cm diameter, 0.5 cm long) at 150 m/s and 450 K. The volume-average diameter is 3.61 mm and $a_c=998$ m²/m³. The conversion in a 0.05 m bed is the starting point of Figure 14.4.
Figure 14.4충전층 안의 농도 감소와 99% 전환에 필요한 길이Concentration Decay in a Packed Bed and the Length for 99% Conversion
예측: 같은 전환율을 얻는 데 필요한 층 길이는 입자 지름 $d_p$를 절반으로 줄이면 어떻게 될까?Predict: how does the bed length needed for the same conversion change if the particle diameter $d_p$ is halved?
목표: 아래 막대의 점을 끌어 유속 $U$를 150 m/s 이상으로 유지하면서 층 길이 0.05 m에서 전환율 99% 이상을 달성하세요.Goal: drag the dots on the bars to keep the velocity $U$ at 150 m/s or more and still reach at least 99% conversion in the 0.05 m bed.
Re—
k_c (m/s)—
a_c (m²/m³)—
전환율 $X$ (L = 0.05 m)Conversion $X$ (L = 0.05 m)—
99% 전환 길이 (m)Length for 99% (m)—
조건은 예제 14-2(헬륨 $\nu=4.94\times10^{-5}$ m²/s, $D_{AB}=1.42\times10^{-4}$ m²/s, $\phi=0.4$)이다. 교재 수치가 인쇄 과정에서 일부 손상되어, 이 그림의 $k_c$는 식 14-65를 직접 계산한 값이다(출발점 $X\approx0.84$). $k_ca_c\propto d_p^{-3/2}$이므로 같은 전환율에 필요한 길이는 $d_p^{3/2}$에 비례하고, $d_p$를 절반으로 하면 0.35배가 된다. 입자를 줄이면 압력 강하가 커지는 점은 이 그림에 넣지 않았다.Conditions are those of Example 14-2 (helium $\nu=4.94\times10^{-5}$ m²/s, $D_{AB}=1.42\times10^{-4}$ m²/s, $\phi=0.4$). Parts of the printed values are damaged in the source text, so $k_c$ here is computed directly from Eq. 14-65 (starting point $X\approx0.84$). Since $k_ca_c\propto d_p^{-3/2}$, the length for a given conversion scales as $d_p^{3/2}$, and halving $d_p$ gives 0.35 times the length. The larger pressure drop of smaller pellets is not included.
물질전달 제한 반응의 특징: 전환율이 유속, 입자 지름, 층 길이에 민감하고 온도에는 약하게 반응한다. 반응 속도 제한 영역은 반대로 온도에 민감하다.Signature of mass transfer limitation: conversion responds to velocity, particle diameter and bed length, and only weakly to temperature. A reaction-limited regime is the opposite and is sensitive to temperature.
제한 영역에서 벗어나는 방법: 입자를 작게 하거나 유속을 올려 $k_c$를 키운다. 식 14-70에 따라 $k_c\propto U^{1/2}d_p^{-1/2}$이다.Escaping the limitation: raise $k_c$ with smaller particles or higher velocity. By Eq. 14-70, $k_c\propto U^{1/2}d_p^{-1/2}$.
Section 14.5
조건을 바꾸면 어떻게 되는가: Robert the WorrierWhat If...? Parameter Sensitivity and Robert the Worrier
Robert는 유량이나 온도 같은 운전 조건을 바꾸면 나쁜 일이 생긴다고 걱정하는 엔지니어이다. 식 14-64에서 전환율은 $k_c$, $a_c$, $U$, $L$로 정해지므로, 각 변수가 조건 변화에 따라 어떻게 바뀌는지만 알면 걱정을 계산으로 바꿀 수 있다. 이 방법이 어림 계산(back-of-the-envelope)이다.Robert is an engineer who worries that changing an operating condition such as flow rate or temperature will make something go wrong. Since Eq. 14-64 sets conversion by $k_c$, $a_c$, $U$ and $L$, knowing how each changes with a condition turns the worry into a calculation. This is the back-of-the-envelope method.
예제 14-3에서는 직렬로 연결된 같은 크기의 두 반응기(전환율 0.865)를 분리해 유량을 반씩 나누어 병렬로 쓰자는 제안을 검토한다. 병렬에서는 $L$이 절반, $U$가 절반이고 $k_c\propto U^{1/2}$이므로 지수가 $0.5\times0.707\times2=0.707$배가 되어 전환율이 0.757로 떨어진다. Robert의 걱정이 맞았다.Example 14-3 considers splitting two identical reactors in series (conversion 0.865) into two parallel reactors, each taking half the flow. In parallel $L$ and $U$ are both halved and $k_c\propto U^{1/2}$, so the exponent becomes $0.5\times0.707\times2=0.707$ times as large and conversion drops to 0.757. Robert's worry was justified.
예제 14-4는 온도를 400°C에서 500°C로 올리면 반응 속도가 $2^{10}$배가 된다는 어림법칙을 검토한다. 표면 반응 속도 상수는 Arrhenius 식으로 크게 오르지만, 이미 물질전달이 속도를 정하고 있으면 $k_c$만 완만하게 오른다. 그림 14.5에서 활성화 에너지에 따라 겉보기 활성화 에너지가 어떻게 달라지는지 본다.Example 14-4 tests the rule of thumb that raising the temperature from 400 °C to 500 °C multiplies the rate by $2^{10}$. The surface rate constant rises steeply by the Arrhenius law, but if mass transfer already sets the rate, only the modest increase of $k_c$ counts. Figure 14.5 shows how the apparent activation energy depends on the true one.
Figure 14.5온도에 따른 관측 속도와 겉보기 활성화 에너지Observed Rate and Apparent Activation Energy Versus Temperature
표면 반응의 $E_a$ (kJ/mol)Surface reaction $E_a$ (kJ/mol)100
운전 온도 $T$ (K)Operating temperature $T$ (K)700
k_r (m/s)0
k_c (m/s)0
관측 속도 상수 (m/s)Observed constant (m/s)0
겉보기 $E_a$ (kJ/mol)Apparent $E_a$ (kJ/mol)0
제한 영역Regime—
모형 값은 교재 자료가 아니고 설명용이다. $k_r=0.02\exp[-E_a/R(1/T-1/800)]$ m/s, $k_c=0.04(T/800)^{1.5}$ m/s로 두었으며, 지수 1.5는 기체 확산도의 온도 의존($T^{1.75}$)과 점도 변화를 합친 근사이다. 낮은 온도에서는 관측 곡선이 $k_r$을 따라 기울기가 $E_a$이고, 높은 온도에서는 $k_c$를 따라 기울기가 $1.5RT$(700 K에서 약 9 kJ/mol)로 낮아진다. 따라서 온도를 올려도 속도는 제한적으로만 오른다.The model values are illustrative, not data from the text: $k_r=0.02\exp[-E_a/R(1/T-1/800)]$ m/s and $k_c=0.04(T/800)^{1.5}$ m/s, where the exponent 1.5 approximates the gas diffusivity ($T^{1.75}$) combined with viscosity changes. At low temperature the observed curve follows $k_r$ with slope $E_a$; at high temperature it follows $k_c$ with slope $1.5RT$ (about 9 kJ/mol at 700 K). Raising the temperature then buys only a limited rate gain.
진단 방법: 겉보기 활성화 에너지가 수 kJ/mol에서 20 kJ/mol 이하이면 물질전달 제한을 의심한다. 유속을 올렸을 때 속도가 $U^{1/2}$로 오르는지도 확인한다.Diagnosis: an apparent activation energy from a few kJ/mol up to about 20 kJ/mol suggests mass transfer limitation. Check also whether the rate rises as $U^{1/2}$ when the velocity is raised.
예제 14-4의 결론: 표면 반응이 온도에 더 민감하므로 온도를 올릴수록 반응은 더욱 물질전달 제한이 된다. 100°C를 올려도 속도는 수십 퍼센트 정도 오른다.Conclusion of Example 14-4: the surface reaction is more temperature sensitive, so heating makes the system more mass-transfer-limited. A 100 °C rise raises the rate by tens of percent.
이 절은 입자 반응에 같은 물질전달 개념을 확장한 보충 내용이다. 이 장의 교재 본문에는 없으며 표준 shrinking core 모형을 따른다. 반응 입자가 구형이고 반응이 바깥쪽에서 안쪽으로 진행되어 반응하지 않은 코어 반지름 $r_c$가 줄어든다고 가정한다. 석탄 가스화에서는 재가 남아 회분층이 되고, 코크스가 쌓인 촉매의 재생에서는 산소가 입자 안으로 들어간다.This section extends the same mass transfer ideas to reacting particles. It is supplementary material that is not in the text of this chapter and follows the standard shrinking core model. The particle is a sphere that reacts from the outside in, so the unreacted core radius $r_c$ shrinks. In coal gasification the ash remains as a layer, and in regeneration of coked catalyst oxygen has to enter the particle.
반응물이 거치는 세 단계가 직렬 저항이다. 첫째는 기체막을 통한 외부 물질전달, 둘째는 회분층 안의 확산, 셋째는 코어 표면의 반응이다. 각 단계가 단독으로 속도를 정할 때 완전 반응 시간이 $\tau_f\propto R$, $\tau_a\propto R^2$, $\tau_r\propto R$이므로, 입자 지름을 바꿔 보면 어느 단계가 지배하는지 알 수 있다.The reactant passes three steps in series: external mass transfer through the gas film, diffusion through the ash layer, and reaction at the core surface. When each alone controls, the complete-conversion times scale as $\tau_f\propto R$, $\tau_a\propto R^2$ and $\tau_r\propto R$, so changing the particle size reveals which step dominates.
Figure 14.6Shrinking core 입자의 코어 반지름과 완전 반응 시간Core Radius and Time to Complete Conversion of a Shrinking Core Particle
예측: 회분층 확산이 속도를 정할 때 입자 반지름 $R$을 2배로 키우면 완전 반응 시간은 몇 배가 될까?Predict: when ash-layer diffusion controls, how many times longer is the complete reaction if the particle radius $R$ is doubled?
목표: 아래 막대의 시간 점을 끌어 코어 반지름이 처음 반지름의 절반이 되는 시간을 오차 3% 이내로 찾으세요. 시나리오를 바꾸면 그 시간이 달라집니다.Goal: drag the time dot on the bar to find the time at which the core radius is half of the initial radius, within 3%. Changing the scenario changes that time.
입자 반지름 $R$ (mm)Particle radius $R$ (mm)2.0
시간 $t$ (s)Time $t$ (s)—
전환율 $X$Conversion $X$—
r_c / R—
완전 반응 시간 (s)Time to complete (s)—
지배 단계Controlling step—
$R=2$ mm에서 세 단계의 시간은 시나리오별로 임의로 정한 설명용 값이다. 기체막 제어는 $(\tau_f,\tau_a,\tau_r)=(600,40,30)$ s, 회분층 제어는 $(40,900,60)$ s, 표면 반응 제어는 $(30,40,500)$ s이며, $R$에 따라 $\tau_f\propto R$, $\tau_a\propto R^2$, $\tau_r\propto R$로 바뀐다. 코어가 줄수록 회분층이 두꺼워지므로 회분층 제어에서는 시간이 지날수록 전환 속도가 느려진다. 기체막 제어에서 $X$는 시간에 비례해 직선으로 오른다.The three times at $R=2$ mm are illustrative values assigned per scenario: gas film control $(\tau_f,\tau_a,\tau_r)=(600,40,30)$ s, ash layer control $(40,900,60)$ s, surface reaction control $(30,40,500)$ s, scaled with $R$ as $\tau_f\propto R$, $\tau_a\propto R^2$, $\tau_r\propto R$. As the core shrinks the ash layer thickens, so under ash control conversion slows with time. Under gas film control $X$ rises linearly in time.
용해: 고체 구가 액체에 녹을 때는 물질전달 계수 $k_c$가 속도를 정하며, 입자 반지름 자체가 줄어든다. 정체 유체($\mathrm{Sh}=2$)에서는 완전 용해 시간이 $R^2$에 비례한다.Dissolution: when a solid sphere dissolves, $k_c$ sets the rate and the particle radius itself shrinks. In a stagnant fluid ($\mathrm{Sh}=2$) the complete dissolution time scales with $R^2$.
입자 지름 시험: 지름을 2배로 하여 시간이 2배이면 기체막 또는 표면 반응이, 4배이면 회분층 확산이 지배한다. 기체막과 표면 반응은 유속을 바꾸면 구별된다.Size test: doubling the diameter doubles the time under gas film or surface reaction control and quadruples it under ash layer control. Gas film and surface reaction are told apart by changing the velocity.
Self-Check
확인 문제Quiz
Q1. Sherwood 수 $\mathrm{Sh}=k_cd_p/D_{AB}$는 무엇의 비인가?Q1. What does the Sherwood number $\mathrm{Sh}=k_cd_p/D_{AB}$ compare?
$k_c=D_{AB}/\delta$이므로 $\mathrm{Sh}=d_p/\delta$이다. 첫째 보기는 Reynolds 수, 셋째 보기는 Schmidt 수이다.Since $k_c=D_{AB}/\delta$, $\mathrm{Sh}=d_p/\delta$. The first option is the Reynolds number and the third is the Schmidt number.
Q2. 물질전달 제한인 충전층에서 전환율이 0.865이다. 다른 조건은 그대로 두고 유속 $U$를 4배로 올리면 전환율은 얼마가 되는가? ($k_c\propto U^{1/2}$)Q2. A mass-transfer-limited packed bed gives conversion 0.865. Keeping everything else fixed, what is the conversion if $U$ is quadrupled? ($k_c\propto U^{1/2}$)
$\ln[1/(1-0.865)]=2.0$이다. 지수 $k_ca_cL/U\propto U^{1/2}/U=U^{-1/2}$이므로 $U$를 4배로 올리면 지수는 1.0이 되고 $X=1-e^{-1}=0.63$이다. 유속을 올리면 $k_c$는 커지지만 체류 시간이 더 짧아져 전환율은 내려간다.$\ln[1/(1-0.865)]=2.0$. The exponent $k_ca_cL/U\propto U^{1/2}/U=U^{-1/2}$, so quadrupling $U$ halves it to 1.0 and $X=1-e^{-1}=0.63$. A higher velocity raises $k_c$, but the residence time shortens more, so conversion falls.
Q3. 외부 물질전달이 속도를 정하는 반응에서 온도를 크게 올렸을 때 전환율의 변화는?Q3. In a reaction controlled by external mass transfer, what happens to conversion when the temperature is raised substantially?
물질전달 제한에서는 $r\approx k_cC_{Ab}$이고 $k_c$는 온도에 대해 $T^{1.5}$에서 $T^{1.75}$ 정도로만 변한다. 표면 반응 속도 상수가 지수적으로 오르더라도 직렬 저항 중 큰 쪽이 속도를 정하므로 관측 속도는 거의 오르지 않는다(예제 14-4).Under mass transfer limitation $r\approx k_cC_{Ab}$, and $k_c$ varies only as roughly $T^{1.5}$ to $T^{1.75}$. Even if the surface rate constant rises exponentially, the larger of the series resistances sets the rate, so the observed rate barely rises (Example 14-4).
What If?
만약에?What If?
만약 촉매 입자의 지름을 절반으로 줄인다면?What if the catalyst particle diameter is halved?
클릭하여 확인 →Click to reveal →
$k_c\propto d_p^{-1/2}$이고 $a_c\propto d_p^{-1}$이므로 $k_ca_c$가 $2^{3/2}=2.8$배가 된다. 같은 전환율에 필요한 층 길이는 0.35배이다. 작은 입자는 물질전달 제한에서 벗어나는 방법이지만 압력 강하가 커져 펌프 동력이 늘어난다.With $k_c\propto d_p^{-1/2}$ and $a_c\propto d_p^{-1}$, $k_ca_c$ rises by $2^{3/2}=2.8$ times. The bed length for the same conversion is 0.35 times. Small particles escape mass transfer limitation but raise the pressure drop and pumping power.
만약 직렬 반응기 두 대를 병렬로 나누어 유량을 반씩 보낸다면?What if two reactors in series are split into parallel reactors, each taking half the flow?
클릭하여 확인 →Click to reveal →
예제 14-3의 계산대로 지수가 0.707배가 되어 전환율이 0.865에서 0.757로 내려간다. 유속이 절반이면 압력 강하는 줄지만 $k_c\propto U^{1/2}$도 같이 내려간다. 압력 강하를 줄이려는 목적이 아니라 전환율이 목표라면 좋은 변경이 아니다.As computed in Example 14-3 the exponent becomes 0.707 times as large and conversion falls from 0.865 to 0.757. Half the velocity lowers the pressure drop but also lowers $k_c\propto U^{1/2}$. If conversion is the goal, this is not a good change.
만약 반응 온도를 400°C에서 500°C로 올린다면?What if the reaction temperature is raised from 400 °C to 500 °C?
클릭하여 확인 →Click to reveal →
반응이 물질전달 제한이면 $2^{10}$배는커녕 몇십 퍼센트 정도만 오른다. 표면 반응 속도 상수는 크게 오르지만 $k_c$는 $D_{AB}$와 점도를 통해 완만하게 오르기 때문이다. 이미 제한 상태이므로 온도를 올릴수록 물질전달 제한이 더 강해진다.If the reaction is mass-transfer-limited, the rate gains tens of percent rather than $2^{10}$. The surface rate constant rises sharply, but $k_c$ rises modestly through $D_{AB}$ and viscosity. The system is already limited, so heating makes the limitation stronger.
Key Takeaways
01
플럭스는 확산과 대류의 합Flux Is Diffusion Plus Bulk Flow
$W_A=J_A+B_A$이다. 등몰 역방향 확산은 직선 분포이고, 정체 막은 로그 분포이며 조성이 높을수록 플럭스가 커진다.$W_A=J_A+B_A$. Equimolar counterdiffusion gives a linear profile; a stagnant film gives a logarithmic one with a larger flux at higher composition.
02
kc는 상관식으로 구한다Find kc from Correlations
$k_c=D_{AB}/\delta$이고 $\mathrm{Sh}=2+0.6\mathrm{Re}^{1/2}\mathrm{Sc}^{1/3}$ 또는 Thoenes-Kramers 식으로 계산한다. $k_c\propto U^{1/2}d_p^{-1/2}$이다.$k_c=D_{AB}/\delta$, computed from $\mathrm{Sh}=2+0.6\mathrm{Re}^{1/2}\mathrm{Sc}^{1/3}$ or the Thoenes-Kramers equation. $k_c\propto U^{1/2}d_p^{-1/2}$.
03
충전층 전환율과 영역 진단Bed Conversion and Regime Diagnosis
$X=1-\exp(-k_ca_cL/U)$이다. 속도가 $U$와 $d_p$에 민감하고 온도에 둔하면 물질전달 제한이다.$X=1-\exp(-k_ca_cL/U)$. A rate that is sensitive to $U$ and $d_p$ but insensitive to temperature indicates mass transfer limitation.
04
조건 변화는 계산으로 확인Check Changes by Calculation
Robert의 걱정은 $k_c$, $a_c$, $U$, $L$의 변화를 식에 넣으면 풀린다. Shrinking core에서는 $R$을 바꾼 시간 비로 지배 단계를 가른다.Robert's worries are settled by inserting the changes in $k_c$, $a_c$, $U$ and $L$ into the equation. In the shrinking core model the time ratio on changing $R$ identifies the controlling step.