비정상 상태 비등온 반응기 설계Unsteady-State Nonisothermal Reactor Design
Fogler, Elements of Chemical Reaction Engineering, Chapter 13. 냉각수 유량, 공급 속도, 초기 조건을 끌어 움직이면 온도와 전환율이 실시간으로 바뀐다.Fogler, Elements of Chemical Reaction Engineering, Chapter 13. Drag the coolant flow, the feed rate, and the initial conditions and watch temperature and conversion respond in real time.
비정상 상태 에너지 수지단열 회분식 반응기냉각 정지와 폭주반회분식 열 제거CSTR 시동다중 반응과 반응기 안전
Section 13.1
비정상 상태 에너지 수지The Unsteady-State Energy Balance
11장과 12장에서는 정상 상태 비등온 반응기를 다뤘다. 이 장에서는 온도와 농도가 시간에 따라 함께 변하는 경우로 넘어간다. 회분식 반응기, 반회분식 반응기, 시동 중인 CSTR이 여기에 해당한다. 비정상 상태 에너지 수지를 몰 수지와 함께 풀면 온도와 전환율을 시간의 함수로 얻는다.Chapters 11 and 12 treated steady-state nonisothermal reactors. This chapter moves to cases where temperature and concentration change together with time: batch reactors, semibatch reactors, and a CSTR during startup. Solving the unsteady energy balance together with the mole balances gives temperature and conversion as functions of time.
유도는 계의 총 에너지 $\sum N_iE_i$의 시간 변화에서 시작한다. 위치 에너지와 운동 에너지의 변화는 무시하고, 내부 에너지 $U_i$를 엔탈피 $H_i$로 바꿀 때 생기는 $PV$ 항도 다른 항보다 훨씬 작으므로 버린다. 여기에 각 화학종의 몰 수지 $dN_i/dt=F_{i0}-F_i+r_iV$를 대입하면 온도 $T$에 대한 식 하나가 남는다.The derivation starts from the time change of the total system energy $\sum N_iE_i$. Changes in potential and kinetic energy are neglected, and the $PV$ term that appears when internal energy $U_i$ is replaced by enthalpy $H_i$ is dropped because it is much smaller than the other terms. Substituting the mole balance of each species, $dN_i/dt=F_{i0}-F_i+r_iV$, leaves one equation for the temperature $T$.
분자는 열이 들어오고 나가는 속도의 합이고, 분모 $\sum N_iC_{Pi}$는 반응기 안의 모든 물질의 온도를 1 K 올리는 데 필요한 열량이다. 분모가 크면 같은 열이 들어와도 온도가 천천히 변한다. 반응기에 물질이 많이 들어 있거나 용매 열용량이 클수록 온도가 안정하다.The numerator is the sum of heat flows in and out, and the denominator $\sum N_iC_{Pi}$ is the heat needed to raise everything in the reactor by 1 K. A large denominator makes temperature change slowly for the same heat input. More material or a solvent with larger heat capacity makes the temperature steadier.
발열 속도와 제열 속도: $\dot Q_g$는 반응이 만드는 열이고 $\dot Q_r$는 유입 물질을 데우는 데 쓰이는 열과 열교환기가 빼는 열의 합이다. $\dot Q_g>\dot Q_r$이면 온도가 올라가고, 같으면 온도가 변하지 않는다.Heat generated and heat removed: $\dot Q_g$ is the heat made by reaction; $\dot Q_r$ is the heat spent on warming the feed plus the heat taken away by the exchanger. Temperature rises when $\dot Q_g>\dot Q_r$ and holds when they are equal.
회분식 반응기의 단순화: 유입과 유출이 없으므로 $F_{i0}$ 항이 사라진다. 축 일 $\dot W_s$는 보통 무시한다. 남는 식은 $\dot Q_g$와 열교환 $\dot Q$ 두 항뿐이다.Batch simplification: with no inflow or outflow the $F_{i0}$ term vanishes, and shaft work $\dot W_s$ is usually neglected. Only $\dot Q_g$ and the exchanger term $\dot Q$ remain.
열교환기 식: 냉각수가 열교환기를 지나며 온도가 $T_{a1}$에서 $T_{a2}$로 변하는 경우에 쓴다. 냉각수 유량이 매우 크면 $\dot Q\to UA\,(T_a-T)$가 된다.Exchanger expression: used when the coolant temperature changes from $T_{a1}$ to $T_{a2}$ along the exchanger. For a very large coolant flow it reduces to $\dot Q\to UA\,(T_a-T)$.
Figure 13.1단열 회분식 반응기의 전환율에 따른 온도Temperature versus Conversion in an Adiabatic Batch Reactor
초기 온도 $T_0$ (K)Initial temperature $T_0$ (K)276
메탄올 양 $N_M$ (mol)Methanol charge $N_M$ (mol)99
완전 전환 시 단열 온도 (K)Adiabatic T at X = 1 (K)—
350 K에 이르는 전환율Conversion at 350 K—
ΣN C_P (cal/K)—
예제 13-1의 값($N_{A0}=54.8$ mol, 물 555 mol, $\Delta H_{Rx}=-20{,}202$ cal/mol, $C_{PA}=35$, $C_{PB}=18$, $C_{PC}=46$, $C_{PM}=19.5$ cal/(mol K))으로 $T=T_0+[-\Delta H_{Rx}]X/(\sum\Theta_iC_{Pi}+\Delta C_PX)$를 그렸다. 초기 온도가 높을수록 같은 전환율에서 온도가 그만큼 높아지고, 메탄올 같은 불활성 용매를 더하면 같은 반응열이 더 많은 열용량에 나뉘어 온도 상승이 줄어든다. 점선은 부반응이 시작되는 350 K이다.Plotted from Example 13-1 values ($N_{A0}=54.8$ mol, water 555 mol, $\Delta H_{Rx}=-20{,}202$ cal/mol, $C_{PA}=35$, $C_{PB}=18$, $C_{PC}=46$, $C_{PM}=19.5$ cal/(mol K)) using $T=T_0+[-\Delta H_{Rx}]X/(\sum\Theta_iC_{Pi}+\Delta C_PX)$. A higher initial temperature lifts the whole curve, and an inert solvent such as methanol spreads the same reaction heat over more heat capacity so the rise is smaller. The dashed line is the 350 K onset of the side reaction.
Section 13.2
회분식 반응기의 에너지 수지Energy Balance on Batch Reactors
회분식 반응기에서는 유입과 유출이 없으므로 에너지 수지는 $\dot Q_g$와 열교환만으로 쓰인다. 몰 수지 $dX/dt=-r_AV/N_{A0}$와 함께 $X(t)$와 $T(t)$ 두 개의 상미분방정식을 동시에 푼다. 반응 속도 상수가 $k=A\exp(-E/RT)$이므로 온도가 오르면 속도가 빨라지고, 속도가 빨라지면 온도가 더 빨리 오르는 되먹임이 생긴다. 이 되먹임이 폭주(runaway)의 원인이다.With no inflow or outflow, the batch energy balance contains only $\dot Q_g$ and heat exchange. It is solved together with the mole balance $dX/dt=-r_AV/N_{A0}$, two coupled ODEs for $X(t)$ and $T(t)$. Since $k=A\exp(-E/RT)$, a higher temperature speeds the reaction and a faster reaction raises temperature faster. This feedback is the origin of runaway.
13.2.1 단열 운전: 열교환이 없으면 에너지 수지와 몰 수지를 하나로 합쳐 $T$와 $X$의 대수 관계를 얻는다. 어떤 온도에서 시작해도 최종 온도는 반응열과 열용량으로 정해지므로 반응기를 설계하기 전에 최대 단열 온도를 먼저 계산할 수 있다. 시간은 $t=N_{A0}\int_0^X dX/(-r_AV)$로 구한다.13.2.1 Adiabatic operation: without heat exchange the energy and mole balances combine into an algebraic relation between $T$ and $X$. The final temperature is fixed by the reaction heat and heat capacity, so the maximum adiabatic temperature can be computed before the reactor is designed. Time follows from $t=N_{A0}\int_0^X dX/(-r_AV)$.
예제 13-1은 프로필렌 글리콜 합성의 단열 회분식 시험이다. 40 dm³ 반응기에 에틸렌 옥사이드 4 dm³(54.8 mol), 메탄올 4 dm³(98.8 mol), 0.1 wt% H₂SO₄ 수용액 10 dm³(물 555 mol)을 넣고 276 K에서 시작한다. 350 K를 넘으면 더 큰 발열 부반응이 시작되므로 단열 운전이 안전한지, 열교환기를 달면 얼마나 낮아지는지 확인한다. 열교환기는 $UA=10$ cal/(s K), 냉각수 유량 10 g/s, 입구 온도 290 K이다.Example 13-1 is an adiabatic batch test for propylene glycol. A 40 dm³ reactor is charged with 4 dm³ ethylene oxide (54.8 mol), 4 dm³ methanol (98.8 mol), and 10 dm³ of 0.1 wt% H₂SO₄ water (555 mol of water) at 276 K. Above 350 K a more exothermic side reaction begins, so the question is whether adiabatic operation is safe and how much a heat exchanger helps. The exchanger has $UA=10$ cal/(s K) and coolant at 10 g/s and 290 K.
반응열이 온도로 바뀌는 비율: 예제 13-1은 완전 전환 시 단열 온도 상승이 약 82 K이다. 276 K에서 시작하면 357 K까지 올라가 350 K 한계를 넘는다.How reaction heat becomes temperature: in Example 13-1 the adiabatic rise at full conversion is about 82 K. Starting at 276 K it reaches 357 K and passes the 350 K limit.
시작 온도와 시간: $E/R\approx9060$ K이면 시작 온도를 15 K 올릴 때 $k$가 약 5배 커진다. 온도 한계 안에서 시작 온도를 높이면 배치 시간이 크게 줄지만 최고 온도도 같이 올라간다.Start temperature and time: with $E/R\approx9060$ K, raising the start temperature by 15 K makes $k$ about five times larger. Within the temperature limit a hotter start shortens the batch a lot, but the peak temperature rises too.
재구성한 값: PDF에서 활성화 에너지가 32,400으로 읽히지만 영국 단위(Btu/lb-mol)의 값이다. mks로 환산하면 18,000 cal/mol이고 $E/R=9060$ K이다.Reconstructed value: the PDF text reads the activation energy as 32,400, which is in English units (Btu/lb-mol). Converted, it is 18,000 cal/mol and $E/R=9060$ K.
Figure 13.2초기 온도와 냉각수 유량에 따른 회분식 반응기의 T(t), X(t)Batch Reactor T(t) and X(t) versus Initial Temperature and Coolant Flow
예측: 냉각 없이(단열) 초기 온도를 276 K에서 291 K로 15 K 올리면 전환율 0.9에 이르는 시간은 어떻게 될까?Predict: with no cooling (adiabatic), if the initial temperature is raised by 15 K from 276 K to 291 K, what happens to the time to reach conversion 0.9?
목표: 위쪽 사각형에서 점을 끌어 초기 온도(가로)와 냉각수 유량(세로)을 정하고, 최고 온도 350 K 이하로 전환율 0.9에 32분 안에 도달하세요. 높게 시작하면 빠르지만 최고 온도가 한계를 넘습니다.Goal: drag the dot in the upper square to set the initial temperature (horizontal) and coolant flow (vertical), and reach conversion 0.9 within 32 min while the peak stays at or below 350 K. A hot start is fast but passes the limit.
초기 온도 (K)Initial T (K)—
냉각수 유량 (g/s)Coolant flow (g/s)—
최고 온도 (K)Peak T (K)—
X = 0.9 도달 시간 (분)Time to X = 0.9 (min)—
모델은 예제 13-1의 1차 반응($-r_A=kC_A$)에 $UA=10$ cal/(s K), 냉각수 입구 290 K, $C_{Pc}=4.16$ cal/(g K)를 쓰고 이 페이지에서 4차 Runge-Kutta로 적분했다. 냉각수 유량을 올려도 $UA$가 상한이므로 제열 속도는 $10\,(T-290)$ cal/s를 넘지 못한다. 그래서 시간을 가장 줄이는 조건은 290 K 안팎에서 시작하고 냉각수를 충분히 흘려 최고 온도를 한계에 맞추는 것이다.The model uses the first-order rate law of Example 13-1 ($-r_A=kC_A$) with $UA=10$ cal/(s K), coolant inlet 290 K, and $C_{Pc}=4.16$ cal/(g K), integrated here by fourth-order Runge-Kutta. Because $UA$ is the ceiling, removal cannot exceed $10\,(T-290)$ cal/s however fast the coolant flows. The fastest safe batch therefore starts near 290 K with ample coolant so the peak just meets the limit.
13.2.2 냉각이 중단된 등온 운전: 등온 운전은 열교환기 제어로 유지된다. 열교환기가 멈추면 어떻게 되는지를 보여주는 사례가 Monsanto사 Sauget 공장의 사고이다. 이 반응기는 암모니아와 o-니트로클로로벤젠(ONCB)으로 니트로아닐린을 만들었고 $\mathrm{A}+2\mathrm{B}\rightarrow\mathrm{C}+\mathrm{D}$, $-r_A=kC_AC_B$ 형태의 속도식을 따랐다. 평소에는 175°C(448 K), 약 500 psi에서 24시간 동안 등온으로 운전했다.13.2.2 Isothermal operation interrupted by cooling loss: isothermal operation is held by controlling the heat exchanger. The accident at the Monsanto plant in Sauget shows what happens when the exchanger stops. The reactor made nitroaniline from ammonia and o-nitrochlorobenzene (ONCB), $\mathrm{A}+2\mathrm{B}\rightarrow\mathrm{C}+\mathrm{D}$ with $-r_A=kC_AC_B$. Normally it ran isothermally at 175°C (448 K) and about 500 psi for 24 h.
사고 당일에는 두 가지가 달랐다. 첫째, ONCB를 평소 3.17 kmol 대신 9.04 kmol 넣었다(반응 부피 3.27 m³에서 5.12 m³). 둘째, 반응 시작 45분 뒤 냉각이 약 10분 중단되었다. 냉각은 이전에도 가끔 10분 정도 멈췄으나 문제가 없었다. 반응기에는 약 700 psi에서 열리는 파열판이 있었는데, 열리면 압력이 내려가 물이 증발하면서 반응이 식었을 것이다.Two things differed on the day of the accident. First, 9.04 kmol of ONCB was charged instead of the usual 3.17 kmol (reaction volume from 3.27 m³ to 5.12 m³). Second, cooling stopped for about 10 min, 45 min after the start. Cooling had stopped for about 10 min before without trouble. The reactor had a rupture disk set near 700 psi; had it opened, the pressure drop would have boiled water and quenched the reaction.
에너지 수지는 $\sum N_iC_{Pi}=2504$ kcal/K(새 충전)를 분모로 하고 $\dot Q_g=(-r_AV)(-\Delta H_{Rx})$, $\dot Q_r=UA\,(T-T_a)$를 분자로 한다. $UA=35.85$ kcal/(min K), $T_a=298$ K, 속도 상수는 461 K에서 $k=0.00017$ m³/(kmol min), $E=11{,}273$ cal/mol이다. 분석 결과, 증가한 충전량, 초기의 냉각 중단, 안전장치 고장 세 조건이 모두 있어야 폭발이 일어난다.The energy balance has $\sum N_iC_{Pi}=2504$ kcal/K (new charge) in the denominator and $\dot Q_g=(-r_AV)(-\Delta H_{Rx})$, $\dot Q_r=UA\,(T-T_a)$ in the numerator. $UA=35.85$ kcal/(min K), $T_a=298$ K, and $k=0.00017$ m³/(kmol min) at 461 K with $E=11{,}273$ cal/mol. The analysis shows that all three conditions are needed for the explosion: the larger charge, the early cooling loss, and the failed relief system.
복구 뒤에도 폭주하는 조건: 냉각을 다시 켜는 시점의 온도에서 $\dot Q_g$가 $UA\,(T-T_a)$보다 크면 온도는 계속 오른다. 이 경계 온도를 넘었는지에 따라 사고 여부가 결정된다.Runaway after cooling returns: if $\dot Q_g$ at the temperature reached when cooling comes back exceeds $UA\,(T-T_a)$, temperature keeps rising. Whether that boundary temperature was passed decides the accident.
충전량의 영향: 충전량이 많으면 같은 시간에 만드는 열이 많고 온도 상승 후의 $\dot Q_g$ 곡선이 제열 직선보다 높아진다. 같은 10분 중단이 평소 충전량에서는 15 K 정도의 상승으로 끝난다.Effect of the charge: a larger charge makes more heat per unit time, and after a temperature rise the $\dot Q_g$ curve lies above the removal line. The same 10 min outage ends with only about a 15 K rise at the usual charge.
재구성한 값: 반응열은 PDF에서 지수가 지워져 있어 $-5.9\times10^{5}$ kcal/kmol로 복원했다. 이 값에서 448 K 등온 운전의 발열이 제열 한계(5380 kcal/min)보다 낮고, 평소 충전은 회복하며 3배 충전은 폭주해 본문의 결론과 맞는다. 파열판이 열리는 온도 535 K와 용기 파손 온도 600 K는 이 페이지의 가정이다.Reconstructed values: the exponent of the heat of reaction is lost in the PDF; it is restored as $-5.9\times10^{5}$ kcal/kmol. With it the 448 K isothermal heat generation is below the removal limit (5380 kcal/min), the usual charge recovers, and the tripled charge runs away, matching the text. The disk-opening temperature 535 K and vessel failure at 600 K are assumptions of this page.
Figure 13.3니트로아닐린 반응기의 냉각 중단 시각과 폭발까지의 시간Cooling-Loss Timing and Time to Explosion in the Nitroaniline Reactor
예측: 평소 충전량 3.17 kmol에서 같은 10분 냉각 중단이 45분에 일어나면 어떻게 될까?Predict: at the usual charge of 3.17 kmol, what happens if the same 10 min cooling loss occurs at 45 min?
목표: 충전량 9.04 kmol에서 그림을 좌우로 끌어 냉각 중단 시각을 바꾸고, 폭주가 일어나는 가장 늦은 중단 시각을 5분 오차 안에서 찾으세요. 그보다 늦으면 반응물이 줄어 회복합니다.Goal: at the 9.04 kmol charge, drag the figure left and right to change when cooling stops, and find the latest stop time that still causes runaway, within 5 min. Later than that, reactants are depleted and the reactor recovers.
냉각 중단 시각 (분)Cooling stops at (min)—
최고 온도 (K)Peak T (K)—
결과Outcome—
중단 후 사고까지 (분)Minutes from loss to event—
모델은 예제 13-2의 값(448 K 등온, $UA=35.85$ kcal/(min K), $T_a=298$ K, $\Delta H_{Rx}=-5.9\times10^{5}$ kcal/kmol 복원값)을 쓰고 이 페이지에서 적분했다. 파열판이 정상이면 535 K에서 열려 물이 증발하며 반응이 식고, 고장이면 온도가 계속 올라 600 K에서 용기가 파손되는 것으로 가정했다. 중단 시각이 늦을수록 ONCB가 이미 소비되어 $\dot Q_g$가 작아지므로 사고 조건은 사실상 처음 한두 시간 안의 중단에 한정된다.The model uses Example 13-2 values (448 K isothermal, $UA=35.85$ kcal/(min K), $T_a=298$ K, restored $\Delta H_{Rx}=-5.9\times10^{5}$ kcal/kmol), integrated on this page. With a working disk it opens at 535 K and boiling water quenches the reaction; if it fails, temperature keeps rising and the vessel is assumed to fail at 600 K. The later cooling stops, the more ONCB is already consumed and the smaller $\dot Q_g$ is, so the hazard is limited to outages within roughly the first one or two hours.
Figure 13.4냉각 복구 시점의 발열 곡선과 제열 직선Heat-Generation Curve and Removal Line When Cooling Returns
ONCB 충전량 (kmol)ONCB charge (kmol)9.04
냉각 중단 시각 (분)Cooling stops at (min)45
중단 길이 (분)Outage length (min)10
복구 시점 온도 (K)T when cooling returns (K)—
경계 온도 (K)Boundary T (K)—
전환율 XConversion X—
적분 결과Integration result—
복구 시점의 전환율에서 $\dot Q_g(T)$ 곡선과 $UA\,(T-298)$ 직선을 그렸다. 곡선이 직선과 만나는 낮은 쪽 온도가 경계 온도이고, 복구 시점의 온도(초록 점)가 이보다 높으면 냉각을 켜도 $\dot Q_g>\dot Q_r$이라 폭주한다. 충전량 슬라이더는 책의 두 충전(3.17과 9.04 kmol) 사이를 선형으로 보간한 가정이다.At the conversion reached when cooling returns, the $\dot Q_g(T)$ curve is drawn with the $UA\,(T-298)$ line. The lower intersection is the boundary temperature; if the temperature at restoration (green dot) is above it, $\dot Q_g>\dot Q_r$ even with cooling on and the reactor runs away. The charge slider interpolates linearly between the two charges of the text (3.17 and 9.04 kmol), which is an assumption.
Section 13.3
열교환기를 갖춘 반회분식 반응기Semibatch Reactors with a Heat Exchanger
반회분식 반응기는 한 반응물을 천천히 넣어 발열 속도를 조절하는 데 쓴다. 공급을 늦추면 넣는 즉시 반응하므로 발열이 공급 속도로 제한되고, 열교환기가 그 열을 감당할 수 있다. 12장까지는 열교환기 안의 냉각수 온도 $T_a$를 일정하다고 보았다. 이 절에서는 냉각수가 열교환기를 지나며 $T_{a1}$에서 $T_{a2}$로 변한다고 보고, 냉각수 쪽의 정상 상태 가정으로 $\dot Q$를 쓴다.A semibatch reactor adds one reactant slowly to control the rate of heat release. A slower feed reacts on arrival, so the heat release is tied to the feed rate and the exchanger can handle it. Up to Chapter 12 the coolant temperature $T_a$ in the exchanger was taken as constant. Here the coolant is allowed to change from $T_{a1}$ to $T_{a2}$ along the exchanger, and $\dot Q$ is written with a quasi-steady assumption on the coolant side.
부피는 $V=V_0+v_0t$로 늘어나므로 몰 수지는 화학종 수 $N_i$에 대해 쓰고 농도는 $C_i=N_i/V$로 계산한다. 에너지 수지에서는 들어오는 공급 흐름을 $T_0$에서 $T$로 데우는 항 $\sum F_{i0}C_{Pi}(T-T_{i0})$이 새로 나타난다. 분모 $\sum N_iC_{Pi}$는 공급량이 늘어남에 따라 같이 커진다.The volume grows as $V=V_0+v_0t$, so mole balances are written on $N_i$ and concentrations follow from $C_i=N_i/V$. The energy balance gains the term $\sum F_{i0}C_{Pi}(T-T_{i0})$ for heating the incoming stream from $T_0$ to $T$, and the denominator $\sum N_iC_{Pi}$ grows as feed is added.
예제 13-3은 에틸 아세테이트(A)와 NaOH(B)의 2차 비누화 반응이다. 처음 0.2 m³에 A가 5 kmol/m³, 물이 30.7 kmol/m³ 있고, 1 kmol/m³ NaOH 수용액을 300 K, 0.004 m³/s로 넣는다. $UA=3000$ J/(s K), 냉각수 100 kg/s, 285 K이며 반응기를 315 K 아래로 유지해야 한다. 공급한 B가 들어오는 즉시 소비되어 A는 약 250초 안에 거의 사라지고, 책은 이 반응에 반회분식 반응기가 알맞지 않다는 뜻으로 "Wrong Reactor Choice"라고 표시한다.Example 13-3 is the second-order saponification of ethyl acetate (A) with NaOH (B). The initial 0.2 m³ holds A at 5 kmol/m³ and water at 30.7 kmol/m³, and 1 kmol/m³ NaOH is fed at 300 K and 0.004 m³/s. $UA=3000$ J/(s K), coolant is 100 kg/s at 285 K, and the reactor must stay below 315 K. B is consumed as it arrives, so A is nearly gone within about 250 s, and the text labels the figure "Wrong Reactor Choice", meaning a semibatch reactor does not suit this reaction.
온도 상승이 공급 속도에 비례하는 이유: B는 들어오는 즉시 소비되므로 발열 속도는 공급 속도 $F_{B0}$와 반응열의 곱 근처에 머문다. 공급 속도를 두 배로 하면 발열도 두 배가 되지만 공급이 절반 시간에 끝나서 최고 온도는 두 배가 되지 않는다.Why heating follows the feed rate: B is consumed on arrival, so the heating rate stays near $F_{B0}$ times the heat of reaction. Doubling the feed doubles the heating, but the feed ends in half the time, so the peak temperature does not double.
열용량의 효과: 탱크 안에 물이 많아 열용량이 크므로 반응열의 대부분은 열교환기로 나가지 않고 액체의 온도를 올린다. 이 예제에서 $UA$를 두 배로 해도 최고 온도는 몇 K만 내려간다.Effect of heat capacity: the tank holds a lot of water, so most of the reaction heat warms the liquid instead of leaving through the exchanger. In this example doubling $UA$ lowers the peak by only a few kelvin.
재구성한 값: $\Delta H_{Rx}=-79{,}076$ kJ/kmol, $C_{PA}=170.7$ kJ/(kmol K), 나머지 화학종 $C_P=75.24$ kJ/(kmol K)로 읽었다. 모든 값은 PDF에서 읽을 수 있었으나 그림 E13-3의 곡선은 읽을 수 없어 이 페이지가 직접 적분한 결과로 대신한다.Reconstructed values: $\Delta H_{Rx}=-79{,}076$ kJ/kmol, $C_{PA}=170.7$ kJ/(kmol K), and $C_P=75.24$ kJ/(kmol K) for the other species. All numbers were legible in the PDF, but the curves of Figure E13-3 were not, so this page's own integration stands in for them.
Figure 13.5NaOH 공급 속도와 열교환기 용량에 따른 반회분식 반응기 온도Semibatch Temperature versus NaOH Feed Rate and Exchanger Capacity
예측: 열교환기를 그대로 두고 NaOH 공급 속도를 두 배로 올리면 최고 온도 상승(300 K 대비)은 어떻게 될까?Predict: with the exchanger unchanged, if the NaOH feed rate is doubled, what happens to the peak temperature rise above 300 K?
목표: 위쪽 사각형에서 점을 끌어 공급 속도(가로)와 열교환기 용량 $UA$(세로)를 정하고, 최고 온도 308 K 이하로 A가 90% 소비되는 시간을 200초 이하로 줄이세요. 공급이 느리면 시간 조건이, 열교환기가 작으면 온도 조건이 맞지 않습니다.Goal: drag the dot in the upper square to set the feed rate (horizontal) and exchanger capacity $UA$ (vertical) so that the peak stays at or below 308 K while 90% of A is consumed within 200 s. A slow feed fails the time condition; a small exchanger fails the temperature condition.
공급 속도 (m³/s)Feed rate (m³/s)—
UA (W/K)—
최고 온도 (K)Peak T (K)—
A 90% 소비 시간 (s)Time to 90% A consumed (s)—
모델은 예제 13-3의 값($k=0.39175$ m³/(kmol s)(273 K 기준), $C_{A,i}=5$ kmol/m³, $V_0=0.2$ m³, 공급 300 K, 냉각수 100 kg/s와 285 K)을 쓰고 이 페이지에서 적분했다. 308 K 한계는 책의 315 K보다 엄격하게 잡은 이 그림의 과제 조건이다. 탱크의 열용량이 커서 공급을 늦추면 온도는 내려가지만 반응 시간이 길어지고, $UA$를 키우면 온도는 더 내려가지만 그 효과는 작다.The model uses Example 13-3 values ($k=0.39175$ m³/(kmol s) referenced to 273 K, $C_{A,i}=5$ kmol/m³, $V_0=0.2$ m³, feed at 300 K, coolant 100 kg/s at 285 K), integrated on this page. The 308 K limit is a task condition of this figure, stricter than the 315 K of the text. A large tank heat capacity means a slower feed lowers the temperature but lengthens the reaction, and a larger $UA$ lowers it further but only slightly.
Section 13.4
CSTR의 비정상 상태 운전: 시동Unsteady Operation of a CSTR: Startup
CSTR 시동 시에는 정상 상태에 어떻게 접근하는지를 따져야 한다. 온도가 정상값보다 크게 넘어서면 반응물이나 생성물이 분해될 수 있고, 부반응이 시작되는 온도를 넘으면 안전 문제가 된다. 이 한계를 실용 안정 한계(practical stability limit)라 하며, 반응과 조건마다 반응 안전 담당자가 정한다.When a CSTR is started, how it approaches steady state matters. A large temperature overshoot can degrade a reactant or product, and passing the onset temperature of a side reaction is a safety problem. This limit is called the practical stability limit and is set for each reaction and condition by the reaction safety engineer.
시간에 따른 $T(t)$와 $C_A(t)$를 적분해도 되지만, $C_A$를 가로축 또는 세로축으로 하는 온도-농도 상평면(phase plane)이 접근 과정을 더 잘 보여준다. 상평면에는 $dC_A/dt=0$인 곡선과 $dT/dt=0$인 곡선이 있고, 두 곡선의 교점이 정상 상태이다. 교점이 하나이면 어디서 시작해도 같은 정상 상태에 이르고, 셋이면 초기 조건에 따라 서로 다른 정상 상태에 이른다.Integrating $T(t)$ and $C_A(t)$ in time works, but the temperature-concentration phase plane shows the approach better. It contains the curve $dC_A/dt=0$ and the curve $dT/dt=0$, and their intersections are the steady states. With one intersection every start reaches the same steady state; with three, different starts reach different ones.
예제 13-4는 12-3의 프로필렌 글리콜 CSTR의 시동 과정을 다룬다. 용적 500 gal(66.8 ft³)의 반응기에 처음에는 물과 0.1 wt% H₂SO₄만 75°F로 들어 있다. 공급은 프로필렌 옥사이드 80 lb-mol/h, 물 1000 lb-mol/h, 메탄올 100 lb-mol/h이고 $\Delta H_{Rx}=-36{,}400$ Btu/lb-mol, $UA=16{,}000$ Btu/(h °F), 냉각수 1000 lb-mol/h(60°F)이다. 이 조건의 정상 상태는 약 140°F, 전환율 0.80이다.Example 13-4 starts up the propylene glycol CSTR of Example 12-3. The 500 gal (66.8 ft³) reactor initially holds only water with 0.1 wt% H₂SO₄ at 75°F. The feed is 80 lb-mol/h propylene oxide, 1000 lb-mol/h water, and 100 lb-mol/h methanol, with $\Delta H_{Rx}=-36{,}400$ Btu/lb-mol, $UA=16{,}000$ Btu/(h °F), and coolant 1000 lb-mol/h at 60°F. The steady state of these conditions is about 140°F at conversion 0.80.
정상 상태의 안정성: 교점이 셋일 때 가운데 교점은 불안정이다. 이 점 위에서 시작하면 정상 상태에 머물지만 조금만 벗어나면 낮은 전환율 상태나 높은 전환율 상태로 갈라진다.Stability of steady states: when there are three intersections the middle one is unstable. A start exactly on it stays, but a small deviation sends the reactor to the low or the high conversion state.
초기 농도의 역할: 탱크를 반응물로 채우고 시작하면 처음부터 발열이 크고, 물만 채우고 시작하면 반응물이 들어오며 서서히 데워진다. 따라서 같은 초기 온도라도 초기 농도에 따라 최고 온도가 다르다.Role of initial concentration: starting with a tank filled with reactant gives strong heating at once, while starting with water only warms up slowly as reactant arrives. The same initial temperature therefore gives different peak temperatures for different initial concentrations.
재구성한 값: 반응기 안 물질의 열용량 $\sum N_iC_{Pi}$는 조성에 따라 변하지만 이 그림에서는 4400 Btu/°F로 일정하다고 근사했다. 정상 상태 한 개 조건은 책의 값이고, 정상 상태 세 개 조건은 유량을 2.25배, $UA$를 8000으로 바꾼 이 페이지의 변형이다.Reconstructed values: the heat capacity $\sum N_iC_{Pi}$ varies with composition, but this figure approximates it as constant at 4400 Btu/°F. The single-steady-state case uses the values of the text; the three-steady-state case is a variation of this page with flow scaled by 2.25 and $UA=8000$.
Figure 13.6CSTR 시동의 T-CA 상평면에서 초기 조건에 따른 정상 상태Steady State Reached from Each Initial Condition on the T-CA Phase Plane of CSTR Startup
예측: 예제 13-4 조건에서 탱크를 75°F 대신 200°F의 물로 채워 시동하면 어떤 정상 상태에 이를까?Predict: under the Example 13-4 conditions, if the tank is started with 200°F water instead of 75°F, which steady state does it reach?
목표: 그림 위에서 시작점을 끌어 놓으세요. 책의 조건에서는 최고 온도를 145°F 이하로 유지하며 정상 상태에 이르고, 유량 2.25배 조건에서는 초기 온도 120°F 이하에서 고온 정상 상태(약 174°F)에 이르면 달성입니다.Goal: drag the start point on the plane and release. Succeed by reaching steady state with a peak at or below 145°F under the textbook conditions, and by reaching the hot steady state (about 174°F) from an initial temperature of 120°F or lower under the 2.25-fold flow condition.
시작점 T (°F)Start T (°F)—
시작점 C_A (lb-mol/ft3)Start C_A (lb-mol/ft3)—
도달한 정상 상태Steady state reached—
최고 온도 (°F)Peak T (°F)—
파란 곡선은 $dC_A/dt=0$, 빨간 곡선은 $dT/dt=0$이고 속이 찬 점은 안정, 빈 점은 불안정한 정상 상태이다. 모델은 예제 13-4의 값($k=16.96\times10^{12}\exp[-32400/(1.987\,T_R)]$ h⁻¹, $C_{A0}=0.181$ lb-mol/ft³, $\tau=0.151$ h)을 쓰고 이 페이지에서 적분했다. 정상 상태가 하나이면 시작점은 경로만 바꾸고 도착점은 바꾸지 못하며, 셋이면 시작점의 온도와 농도가 어느 정상 상태에 가는지를 정한다. 145°F 한계는 이 그림의 과제 조건이다.The blue curve is $dC_A/dt=0$ and the red curve is $dT/dt=0$; filled dots are stable and open dots are unstable steady states. The model uses Example 13-4 values ($k=16.96\times10^{12}\exp[-32400/(1.987\,T_R)]$ h⁻¹, $C_{A0}=0.181$ lb-mol/ft³, $\tau=0.151$ h), integrated on this page. With one steady state the start changes only the path, not the destination; with three, the start temperature and concentration decide which one is reached. The 145°F limit is a task condition of this figure.
Section 13.5
비등온 다중 반응과 반응기 안전Nonisothermal Multiple Reactions and Reactor Safety
$q$개의 반응이 일어나는 회분식 또는 반회분식 반응기에서는 발열 항을 반응마다 더한다. 반응 $i$의 반응열 $\Delta H_{Rxij}$는 화학종 $j$ 한 몰당 값이고, 반응 속도 $r_{ij}$는 각 반응의 속도식으로 정한다. 몰 수지는 화학종마다 $dN_j/dt=\sum_i r_{ij}V$로 쓴다. 속도 상수가 모두 Arrhenius 식을 따르고 활성화 에너지가 다르면 온도에 따라 선택도가 바뀐다.In a batch or semibatch reactor with $q$ reactions, the heat generation term is summed over reactions. The heat of reaction $\Delta H_{Rxij}$ is per mole of species $j$ in reaction $i$, and the rates $r_{ij}$ come from the rate law of each reaction. Mole balances are written per species as $dN_j/dt=\sum_i r_{ij}V$. When all rate constants follow Arrhenius laws with different activation energies, selectivity changes with temperature.
예제 13-5는 직렬 반응 $2\mathrm{A}\rightarrow\mathrm{B}\rightarrow3\mathrm{C}$이다. 첫 반응은 발열($\Delta H_{Rx1A}=-6500$ cal/mol A), 둘째 반응은 흡열($\Delta H_{Rx2B}=+8000$ cal/mol B)이고 반회분식 반응기에 순수 A(4 mol/dm³)를 240 dm³/h로 공급한다. 앞 반응이 열을 내고 뒤 반응이 열을 흡수하므로 온도 변화를 줄이는 방향으로 작용하며, 선택도는 온도와 B 농도에 함께 달려 있다. 이 예제의 수치는 PDF에서 일부만 읽혀 이 페이지는 그림으로 다루지 않는다.Example 13-5 is the series reaction $2\mathrm{A}\rightarrow\mathrm{B}\rightarrow3\mathrm{C}$. The first reaction is exothermic ($\Delta H_{Rx1A}=-6500$ cal/mol A), the second endothermic ($\Delta H_{Rx2B}=+8000$ cal/mol B), and pure A (4 mol/dm³) is fed at 240 dm³/h into a semibatch reactor. The first step releases heat and the second absorbs it, so temperature tends to regulate itself, and selectivity depends on both temperature and the B concentration. Only part of the numbers could be read in the PDF, so this page does not draw a figure for it.
예제 13-6은 2007년 12월 T2 Laboratories 폭발이다. 2450 gal 회분식 반응기에서 메틸시클로펜타디엔(A)과 나트륨(B)이 반응해 수소를 만드는 1단계가 진행 중이었다. 반응기가 455.4 K에 이르렀을 때 운전원은 냉각수를 흘릴 수 없었다. 온도가 계속 올라 약 470 K에서 용매 디글림(S)의 분해가 시작되어 수소가 더 빨리 발생했고, 압력이 파열판 설정(28.2 atm)을 넘은 뒤에도 배출보다 발생이 커서 용기가 파손되었다. 4명이 사망했다.Example 13-6 is the T2 Laboratories explosion of December 2007. Step 1 was under way in a 2450 gal batch reactor, where methylcyclopentadiene (A) and sodium (B) react to give hydrogen. When the reactor reached 455.4 K the operator could not start the cooling water. Temperature kept rising, decomposition of the solvent diglyme (S) began near 470 K, hydrogen evolved even faster, and after the pressure passed the rupture disk setting (28.2 atm) generation still exceeded venting until the vessel failed. Four people died.
두 반응의 에너지 규모: T2에서 반응 2의 반응열은 반응 1의 약 7배이다. 반응 2는 약 470 K 이상에서만 빨라지므로 정상 운전에서는 보이지 않다가 냉각 상실로 그 온도에 이르면 갑자기 지배적이 된다.Energy scale of the two reactions: in T2 the heat of reaction 2 is about seven times that of reaction 1. Reaction 2 speeds up only above about 470 K, so it is invisible in normal operation and becomes dominant suddenly once cooling loss brings the batch to that temperature.
반응기 안전의 공통 조건: 13.2의 니트로아닐린 사고와 T2 사고는 모두 냉각 상실, 온도에 따라 급증하는 발열, 용량이 부족하거나 고장 난 압력 방출 장치가 겹쳐 일어났다. 한 가지를 막으면 사고가 나지 않는다.Common safety conditions: both the nitroaniline accident of 13.2 and the T2 accident came from loss of cooling, heat generation rising steeply with temperature, and a pressure-relief system that was undersized or failed. Removing any one of them prevents the accident.
재구성한 값: 반응 1의 $A_{1A}=5.73\times10^{2}$ dm³/(mol h), $E_{1A}=128{,}000$ J/mol, 반응열 두 개는 PDF에서 읽었다. 반응 2의 활성화 에너지는 읽은 값이 비현실적이어서 수치 모델은 만들지 않았다.Reconstructed values: $A_{1A}=5.73\times10^{2}$ dm³/(mol h), $E_{1A}=128{,}000$ J/mol, and both heats of reaction were read from the PDF. The value read for the activation energy of reaction 2 is unphysical, so no numerical model was built from it.
Self-Check
확인 문제Quiz
Q1. 예제 13-1의 단열 회분식 반응기($\Delta H_{Rx}=-20{,}202$ cal/mol, $\sum\Theta_iC_{Pi}=252$ cal/(mol K), $\Delta C_P=-7$ cal/(mol K))에서 전환율 0.5일 때의 온도 상승은?Q1. In the adiabatic batch reactor of Example 13-1 ($\Delta H_{Rx}=-20{,}202$ cal/mol, $\sum\Theta_iC_{Pi}=252$ cal/(mol K), $\Delta C_P=-7$ cal/(mol K)), what is the temperature rise at conversion 0.5?
$\Delta T=20202\times0.5/(252-7\times0.5)=10101/248.5\approx41$ K이다. 단열 반응에서 온도 상승은 전환율에 거의 비례하고, 완전 전환에서 약 82 K이다.$\Delta T=20202\times0.5/(252-7\times0.5)=10101/248.5\approx41$ K. In an adiabatic reactor the rise is nearly proportional to conversion, reaching about 82 K at full conversion.
Q2. 니트로아닐린 반응기에서 냉각이 복구된 뒤에도 폭주가 계속되는 조건은?Q2. In the nitroaniline reactor, what condition lets the runaway continue after cooling is restored?
$dT/dt=(\dot Q_g-\dot Q_r)/\sum N_iC_{Pi}$이므로 냉각을 켜도 $\dot Q_g>UA\,(T-T_a)$이면 온도는 계속 오른다. 온도 448 K는 기준 운전 온도일 뿐이고, 중단 길이는 도달 온도를 정하는 한 요인에 지나지 않는다. 그림 13.4의 경계 온도가 이 조건을 나타낸다.Since $dT/dt=(\dot Q_g-\dot Q_r)/\sum N_iC_{Pi}$, temperature keeps rising even with cooling on if $\dot Q_g>UA\,(T-T_a)$. 448 K is only the normal operating temperature, and outage length is just one factor setting the temperature reached. The boundary temperature in Figure 13.4 expresses this condition.
Q3. 상평면에 정상 상태가 세 개 있는 CSTR에서 가운데 정상 상태는 어떤 성질을 갖는가?Q3. In a CSTR whose phase plane has three steady states, what is the character of the middle one?
세 교점 중 바깥 두 개는 안정, 가운데는 불안정이다. 가운데 점은 수학적으로 정상 상태이지만 작은 교란으로 두 안정 상태 중 하나로 이동하므로 실제 운전에서는 유지되지 않는다. 그림 13.6의 유량 2.25배 조건에서 시작점을 바꿔 보면 경계를 확인할 수 있다.Of the three intersections the outer two are stable and the middle one is unstable. The middle point is a steady state mathematically, but a small disturbance sends it to one of the stable states, so it cannot be held in real operation. Moving the start point in the 2.25-fold flow case of Figure 13.6 shows the boundary.
What If?
만약에?What If?
만약 니트로아닐린 반응기의 파열판이 정상적으로 열렸다면?What if the rupture disk of the nitroaniline reactor had opened as designed?
클릭하여 확인 →Click to reveal →
압력이 내려가면 물이 증발하면서 기화열을 흡수해 반응 혼합물이 식는다. 증발이 곧 제열 수단이 되므로 $\dot Q_r$가 크게 늘어 폭주가 멈춘다. 그림 13.3에서 파열판을 정상으로 두면 535 K에서 사고가 끝난다. 사고에서는 세 조건 중 이것이 지켜지지 않았다.When the pressure drops, water boils and its latent heat cools the mixture. Evaporation becomes the removal mechanism, so $\dot Q_r$ rises sharply and the runaway stops. In Figure 13.3 the event ends at 535 K when the disk is set to work. In the accident this one of the three conditions was not met.
만약 반회분식 반응기에서 반응이 느려 B가 쌓이는 상태로 냉각이 고장 나면?What if cooling fails in a semibatch reactor where the reaction is slow and B accumulates?
클릭하여 확인 →Click to reveal →
반응이 느리면 넣은 B가 소비되지 않고 쌓인다. 쌓인 B는 온도가 오르는 순간 한꺼번에 반응하므로 회분식에서 모든 반응물을 한 번에 넣은 것과 같은 열이 나온다. 반회분식의 안전 이점은 B가 들어오는 즉시 소비될 때만 유효하다. 예제 13-3은 반응이 빨라서 이 문제가 없었다.If the reaction is slow, the B fed in is not consumed and accumulates. The accumulated B reacts all at once as soon as temperature rises, releasing as much heat as a batch charged with all reactants at the start. The safety benefit of semibatch holds only if B is consumed as it arrives. In Example 13-3 the reaction is fast, so this problem did not arise.
만약 단열 회분식 반응기의 초기 온도를 15 K 낮추면?What if the initial temperature of the adiabatic batch reactor is lowered by 15 K?
클릭하여 확인 →Click to reveal →
최종 온도도 15 K 내려가지만 속도 상수는 약 5배 작아져 배치 시간이 5배 가까이 길어진다. 시작 온도가 낮아도 반응이 끝나면 단열 온도 상승 82 K는 그대로이므로 한계에 가까운 최고 온도는 온도 여유만큼만 줄어든다. 안전을 위해 시작 온도를 낮추는 데는 시간 비용이 따른다.The final temperature falls by 15 K too, but the rate constant becomes about five times smaller and the batch takes nearly five times longer. The adiabatic rise of 82 K is unchanged once the reaction finishes, so the peak near the limit drops only by the margin gained. Lowering the start temperature for safety has a time cost.
Key Takeaways
01
온도는 발열과 제열의 차이로 변한다Temperature Follows Heat Generated Minus Removed
$dT/dt=(\dot Q_g-\dot Q_r)/\sum N_iC_{Pi}$를 몰 수지와 함께 풀면 회분식, 반회분식, 시동 중인 CSTR의 $T(t)$를 얻는다.Solving $dT/dt=(\dot Q_g-\dot Q_r)/\sum N_iC_{Pi}$ with the mole balances gives $T(t)$ for batch, semibatch, and CSTR startup.
02
시작 온도와 제열의 균형Balancing Start Temperature and Cooling
단열 온도 상승은 반응열과 열용량으로 정해지고, 시작 온도를 15 K 올리면 시간이 5분의 1이 되지만 최고 온도가 같은 양만큼 올라간다.The adiabatic rise is set by reaction heat and heat capacity; 15 K more at the start cuts time to a fifth but raises the peak by the same 15 K.
03
폭주는 경계 온도를 넘으면 시작된다Runaway Starts Past a Boundary Temperature
$\dot Q_g(T)$ 곡선이 $\dot Q_r(T)$ 직선 위로 올라가는 온도를 넘으면 냉각을 켜도 온도가 오른다. 충전량, 중단 시각, 안전장치 상태가 모두 영향을 준다.Above the temperature where the $\dot Q_g(T)$ curve passes over the $\dot Q_r(T)$ line, temperature rises even with cooling on. Charge, outage time, and relief status all matter.
04
시동 경로는 상평면에서 읽는다Read the Startup Path on the Phase Plane
정상 상태가 여러 개이면 초기 온도와 농도가 도달점을 정하고, 하나이면 최고 온도 초과 여부가 안전 판단 기준이 된다.With several steady states the initial temperature and concentration decide the destination; with one, whether the peak exceeds the limit is the safety criterion.