정상상태 비등온 반응기 설계: 열교환이 있는 유동 반응기Steady-State Nonisothermal Reactor Design: Flow Reactors with Heat Exchange
Fogler, Elements of Chemical Reaction Engineering, Chapter 12. 슬라이더를 움직이면 그래프가 실시간으로 바뀝니다.Fogler, Elements of Chemical Reaction Engineering, Chapter 12. Move the sliders to see the graphs respond in real time.
열교환이 있는 PFR냉각수 co-current와 countercurrentCSTR의 G(T)와 R(T)다중 정상상태점화와 소화 온도다중 반응과 안전
Section 12.1
열교환이 있는 정상상태 관형 반응기Steady-State Tubular Reactor with Heat Exchange
관형 반응기의 원통형 관벽으로 열을 공급하거나 제거하는 경우를 다룬다. 반경 방향 기울기는 없다고 가정하고, 반응기 부피 $V$ 구간에서 에너지 수지를 세운다. 관벽을 통한 열 유입 속도는 총괄 열전달 계수 $U$, 열교환 면적 $A$, 주변 온도 $T_a$와 반응기 온도 $T$의 차이로 주어진다. 반응기 부피당 열교환 면적 $a$는 지름 $D$인 관에서 $4/D$이다.We consider a tubular reactor in which heat is added or removed through the cylindrical wall. Radial gradients are neglected, and the energy balance is written on a slice of reactor volume $V$. The heat input through the wall depends on the overall heat-transfer coefficient $U$, the exchange area $A$, and the difference between the ambient temperature $T_a$ and the reactor temperature $T$. For a tube of diameter $D$, the exchange area per reactor volume is $a = 4/D$.
이 열 유입을 Chapter 11의 에너지 수지에 대입하고, 몰 수지와 엔탈피의 미분 형태를 함께 쓰면 PFR의 에너지 수지가 얻어진다. 분자는 반응으로 생기는 열 $Q_g$와 관벽으로 제거되는 열 $Q_r$의 차이다. 발열 반응에서 $Q_g$가 $Q_r$보다 크면 반응기를 따라 온도가 올라가고, $Q_r$이 더 크면 온도가 내려간다. 흡열 반응에서는 $Q_g$와 $Q_r$이 모두 음수이고, $(-Q_g)$와 $(-Q_r)$의 크기를 비교해 같은 방식으로 판단한다.Substituting this heat input into the Chapter 11 energy balance, together with the differential mole balance and enthalpy, gives the PFR energy balance. The numerator is the difference between the heat generated by reaction, $Q_g$, and the heat removed through the wall, $Q_r$. For an exothermic reaction, the temperature rises along the reactor while $Q_g > Q_r$ and falls once $Q_r > Q_g$. For an endothermic reaction both terms are negative, and the same comparison is made between $(-Q_g)$ and $(-Q_r)$.
전환율을 독립 변수로 쓰면 $F_i = F_{A0}(\Theta_i + \nu_i X)$를 분모에 대입해 아래 식이 되고, packed-bed 반응기에서는 $dW = \rho_b\,dV$를 써서 부피 대신 촉매 질량으로 나타낸다. 이 두 식은 Chapter 11의 Table 11-1에 있는 형태와 같다.With conversion as the independent variable, $F_i = F_{A0}(\Theta_i + \nu_i X)$ goes into the denominator, and for a packed bed $dW = \rho_b\,dV$ converts volume to catalyst mass. Both forms match those in Table 11-1 of Chapter 11.
열 생성 $Q_g$와 열 제거 $Q_r$: $Q_g$는 반응 속도에 비례하고 온도에 대해 지수적으로 증가한다. $Q_r$은 $T - T_a$에 비례한다. 두 곡선의 크기 비교가 $dT/dV$의 부호를 정한다.Heat generated $Q_g$ and heat removed $Q_r$: $Q_g$ scales with the reaction rate and grows exponentially with temperature, while $Q_r$ is proportional to $T - T_a$. Their relative size sets the sign of $dT/dV$.
알고리즘에 다섯 번째 요소 추가: 몰 수지, 속도식, 화학양론, 조합에 더해 에너지 수지를 쓴다. 기체상 반응에서 압력 강하를 포함하면 $T$, $X$, $p$에 대한 세 식을 동시에 풀고, 액상 반응은 $T$와 $X$ 두 식이면 된다.Energy balance as a fifth building block: the energy balance is added to the mole balance, rate law, stoichiometry, and combination steps. A gas-phase reaction with pressure drop needs the equations for $T$, $X$, and $p$ solved together, whereas a liquid-phase reaction needs only $T$ and $X$.
여러 반응으로 확장: 같은 형태의 식이 몰 유량 형태로 다중 반응과 membrane reactor에도 적용된다(12.6절).Extension to multiple reactions: the same form carries over to the molar-flow-rate formulation for multiple reactions and membrane reactors (Section 12.6).
Figure 12.1PFR 내 열 생성과 열 제거, 온도 변화Heat Generation, Heat Removal, and Temperature along a PFR
열전달 계수 $Ua$Heat-transfer coefficient $Ua$5000
냉각 온도 $T_a$ (일정)Coolant temperature $T_a$ (constant)315 K
입구 온도 $T_0$Inlet temperature $T_0$305 K
최고 온도 $T_{max}$ (K)Peak temperature (K)0
hot spot 위치 (m³)Hot-spot position (m³)0
출구 전환율 $X$Exit conversion $X$0
반응기 입구에서는 $Q_g$가 $Q_r$보다 크므로 온도가 올라가고, $Q_g$와 $Q_r$이 만나는 지점에서 온도가 최고가 된다. 그 뒤에는 반응물이 소모되고 평형 전환율 $X_e$가 낮아지므로 $Q_g$가 줄어 온도가 내려간다. Example 12-1의 butane isomerization 값(액상 가역 발열, $\Delta H_{Rx} = -34\,500$ kJ/kmol, $C_{A0} = 1.86$ kmol/m³, 반응기 5 m³)을 쓴 계산이다.Near the inlet $Q_g$ exceeds $Q_r$, so the temperature rises, and it peaks where the two curves cross. Afterward the reactant is consumed and the equilibrium conversion $X_e$ drops, so $Q_g$ declines and the temperature falls. The calculation uses the butane isomerization data of Example 12-1 (liquid-phase reversible exothermic reaction, $\Delta H_{Rx} = -34{,}500$ kJ/kmol, $C_{A0} = 1.86$ kmol/m³, 5 m³ reactor).
Section 12.2
열전달 유체의 에너지 수지Balance on the Heat-Transfer Fluid
열전달 유체는 발열 반응에서는 냉각수, 흡열 반응에서는 가열 매체 역할을 한다. 유체의 유량이 반응 열에 비해 충분히 크면 $T_a$가 반응기를 따라 거의 변하지 않는다. 그렇지 않으면 안쪽 관(반응 혼합물)과 바깥쪽 환형 공간(열전달 유체) 사이의 열교환을 반영해 $T_a$의 변화를 따로 구해야 한다. 열전달 유체의 질량 유량은 $\dot{m}_c$, 열용량은 $C_{P_c}$로 쓴다.The heat-transfer fluid acts as a coolant for exothermic reactions and as a heating medium for endothermic ones. If its flow rate is large compared with the reaction heat, $T_a$ stays nearly constant along the reactor. Otherwise the change in $T_a$ must be found separately from the heat exchange between the inner tube (reacting mixture) and the outer annulus (heat-transfer fluid). The fluid has mass flow rate $\dot{m}_c$ and heat capacity $C_{P_c}$.
co-current에서는 반응물과 열전달 유체가 같은 방향으로 흐르고, 유체는 $V = 0$에서 $T_{a0}$로 들어간다. countercurrent에서는 유체가 반응기 출구 쪽($V = V_f$)에서 $T_{a0}$로 들어가 입구 쪽으로 흐른다. 두 식의 차이는 $(T - T_a)$와 $(T_a - T)$의 부호뿐이다. countercurrent는 $V = 0$에서의 $T_a$를 모르므로, 이 값을 가정하고 출구에서 $T_a = T_{a0}$가 되도록 반복 계산(trial and error)해야 한다.In co-current flow the reactants and the heat-transfer fluid move in the same direction, and the fluid enters at $T_{a0}$ at $V = 0$. In countercurrent flow the fluid enters at $T_{a0}$ at the reactor exit ($V = V_f$) and flows toward the inlet. The two equations differ only in the sign, $(T - T_a)$ versus $(T_a - T)$. Because $T_a$ at $V = 0$ is unknown for countercurrent flow, it must be guessed and iterated (trial and error) until $T_a = T_{a0}$ at the exit.
$T_a$가 일정한 경우: $\dot{m}_c C_{P_c}$가 매우 크면 $dT_a/dV \approx 0$이고, 에너지 수지 하나와 몰 수지만 풀면 된다.Constant $T_a$: when $\dot{m}_c C_{P_c}$ is very large, $dT_a/dV \approx 0$ and only the reactor energy balance and mole balance are needed.
냉각수의 온도 분포: 발열 반응의 co-current 냉각수는 입구에서 출구로 가며 온도가 올라가 반응 혼합물의 온도에 접근한다. 흡열 반응의 가열 매체는 반대로 온도가 내려간다.Coolant temperature profile: in co-current exothermic operation the coolant warms toward the reaction temperature along the reactor, whereas a heating medium for an endothermic reaction cools down.
방향 선택: Example 12-7에서 최고 온도는 co-current 930 K, countercurrent 1100 K, $T_a$ 일정 870 K였다. 부반응을 줄여야 하면 co-current 또는 $T_a$ 일정 조건이 낫다.Choosing the direction: in Example 12-7 the peak temperature was 930 K for co-current, 1100 K for countercurrent, and 870 K for constant $T_a$. If side reactions are a concern, co-current or constant $T_a$ operation is preferable.
Figure 12.2냉각수 방향과 Ua, 입구 온도에 따른 hot spotHot Spot versus Coolant Direction, Ua, and Coolant Inlet Temperature
예측: 같은 $Ua$와 $T_{a0}$에서 냉각수를 countercurrent로 바꾸면 최고 온도는 어떻게 될까?Predict: at the same $Ua$ and $T_{a0}$, what happens to the peak temperature when the coolant is switched to countercurrent?
목표: 그림 위쪽의 두 막대에서 동그라미를 끌어 $Ua$와 냉각수 입구 온도 $T_{a0}$를 바꾸세요. 최고 온도를 330 K 이하로 유지하면서 출구 전환율 $X$를 0.60 이상으로 만드세요.Goal: drag the two knobs on the bars at the top to change $Ua$ and the coolant inlet temperature $T_{a0}$. Keep the peak temperature at or below 330 K while the exit conversion $X$ is at least 0.60.
최고 온도 (K)Peak T (K)0
hot spot 위치 (m³)Hot spot (m³)0
출구 전환율 $X$Exit $X$0
상태Status-
countercurrent에서는 뜨거워진 냉각수가 반응물이 막 들어와 반응이 빠른 입구 쪽에 닿아 냉각 효과가 줄어든다. 이 계산에서는 슬라이더 범위 안에서 countercurrent로 330 K 이하와 $X \geq 0.60$을 동시에 만족하는 조건이 없다. 계산은 Example 12-1의 butane isomerization 값(냉각수 $\dot{m}_c C_{P_c} = 14\,000$ kJ/(h K))을 쓴다.In countercurrent flow the warmed coolant reaches the inlet end, where the reaction is fast, so the cooling is less effective. With this model, no setting within the slider ranges meets both 330 K or below and $X \geq 0.60$ in countercurrent flow. The calculation uses the butane isomerization data of Example 12-1 (coolant $\dot{m}_c C_{P_c} = 14{,}000$ kJ/(h K)).
Section 12.3
열 효과가 있는 PFR, PBR 설계 알고리즘Algorithm for PFR/PBR Design with Heat Effects
기체상 반응의 알고리즘은 몰 수지 $dX/dV = -r_A/F_{A0}$, 속도식과 화학양론, 에너지 수지, 압력 강하식, 열전달 유체의 수지를 한 묶음의 연립 상미분방정식으로 만든다. Polymath 같은 ODE solver로 $X$, $T$, $p$, $T_a$를 동시에 적분한다. countercurrent는 출구 조건을 만족시키는 $T_a(0)$를 반복 계산으로 찾는다.For a gas-phase reaction the algorithm combines the mole balance $dX/dV = -r_A/F_{A0}$, the rate law and stoichiometry, the energy balance, the pressure-drop equation, and the heat-transfer fluid balance into one set of coupled ODEs. An ODE solver such as Polymath integrates $X$, $T$, $p$, and $T_a$ together. For countercurrent flow, $T_a(0)$ is found by iterating until the exit condition is met.
발열 가역 반응(Example 12-1, butane isomerization)에서는 온도가 오르면 평형 전환율 $X_e$가 내려간다. 전환율 $X$는 입구에서는 $X_e$보다 훨씬 작아 빠르게 오르지만, 온도가 높은 영역에서는 $X_e$에 가까워져 더 오르지 못한다. 온도가 다시 내려가야 $X_e$가 커져 추가 전환이 가능하다. 단열 운전에서는 온도가 평형 전환율이 낮은 영역까지 올라가므로 출구 전환율이 낮게 머문다.In the reversible exothermic reaction of Example 12-1 (butane isomerization), raising the temperature lowers the equilibrium conversion $X_e$. Near the inlet $X$ is far below $X_e$ and rises quickly, but in the hot region it approaches $X_e$ and cannot go higher. Further conversion is possible only after the temperature falls and $X_e$ rises again. In adiabatic operation the temperature climbs into the region of low equilibrium conversion, so the exit conversion stays low.
흡열 반응(Example 12-2, 아세톤의 ketene 분해)은 반대 문제를 보인다. 단열로 운전하면 반응이 열을 흡수해 온도가 계속 내려가고, 속도 상수가 지수적으로 작아져 반응이 거의 멈춘다. 같은 1 dm³ 관에서 단열 전환율은 약 0.20에 그친다. 가열 매체를 넣으면 $T$가 유지되어 전환율이 크게 올라간다.The endothermic reaction (Example 12-2, cracking of acetone to ketene) shows the opposite problem. Under adiabatic operation the reaction absorbs heat, the temperature keeps falling, and the rate constant decays exponentially until the reaction nearly stops. In the same 1 dm³ tube the adiabatic conversion reaches only about 0.20. A heating medium keeps the temperature up and raises the conversion considerably.
평형 전환율 $X_e(T)$: 발열 가역 반응에서 온도가 오르면 $K_C$가 작아져 $X_e$가 내려간다. $X$는 $X_e$를 넘을 수 없다.Equilibrium conversion $X_e(T)$: in a reversible exothermic reaction, a higher temperature lowers $K_C$ and thus $X_e$. The conversion $X$ can never exceed $X_e$.
흡열 반응의 단열 운전: 열 공급이 없으면 온도가 내려가고 $k$가 줄어 반응이 멈춘다. 열교환기는 선택이 아니라 설계 조건이다.Adiabatic endothermic operation: with no heat supply the temperature falls, $k$ drops, and the reaction stops. The heat exchanger is a design necessity.
네 가지 운전 방식: Example 12-1과 12-2는 모두 (a) co-current, (b) countercurrent, (c) $T_a$ 일정, (d) 단열 네 경우를 같은 프로그램에서 계수 하나만 바꿔 비교한다. $U$를 0으로 두면 단열, $dT_a/dV$에 $-1$을 곱하면 countercurrent가 된다.Four modes of operation: Examples 12-1 and 12-2 compare (a) co-current, (b) countercurrent, (c) constant $T_a$, and (d) adiabatic operation in one program by changing a single coefficient. Setting $U = 0$ gives adiabatic operation, and multiplying $dT_a/dV$ by $-1$ gives countercurrent flow.
Figure 12.3아세톤 분해의 전환율과 온도 프로파일Conversion and Temperature Profiles of Acetone Cracking
$Ua$ (J/(m³ s K))$Ua$ (J/(m³ s K))16500
가열 매체 온도 $T_a$ (일정)Heating medium temperature $T_a$ (constant)1250 K
관 부피 $V$ (dm³)Tube volume $V$ (dm³)1.0
출구 전환율 $X$Exit $X$0
단열 출구 $X$Adiabatic exit $X$0
출구 온도 (K)Exit T (K)0
$Ua = 0$이면 단열 곡선과 같아져 온도가 1035 K에서 900 K대로 내려가고 전환율이 약 0.20에서 멈춘다. $Ua$가 커지면 반응 혼합물 온도가 $T_a$에 가까워져 같은 부피에서 전환율이 크게 오른다. Example 12-2 값($F_{A0} = 0.0376$ mol/s 한 관당, $\Delta H_{Rx}(298\ \mathrm{K}) = 80.77$ kJ/mol, $\Delta C_P = -9$ J/(mol K), $T_0 = 1035$ K, 1.6 atm)을 쓰고 $T_a$를 일정하다고 가정했다.At $Ua = 0$ the curve is the adiabatic one: the temperature falls from 1035 K into the 900 K range and the conversion stalls near 0.20. A larger $Ua$ pulls the mixture toward $T_a$ and raises the conversion strongly at the same volume. The calculation uses the Example 12-2 data ($F_{A0} = 0.0376$ mol/s per tube, $\Delta H_{Rx}(298\ \mathrm{K}) = 80.77$ kJ/mol, $\Delta C_P = -9$ J/(mol K), $T_0 = 1035$ K, 1.6 atm) and assumes constant $T_a$.
Section 12.4
열 효과가 있는 CSTRCSTR with Heat Effects
정상상태 CSTR의 에너지 수지는 Chapter 11의 일반식에서 출발한다. CSTR은 잘 섞이므로 반응기 안의 온도가 균일하지만, 이것이 등온 운전을 뜻하지는 않는다. 등온이 되는 것은 공급 온도가 반응기 온도와 같을 때뿐이다. 교반기가 유체에 하는 일 $\dot{W}_s$는 계가 하는 일을 양으로 정의하므로 음수이다.The steady-state CSTR energy balance starts from the general equation of Chapter 11. A CSTR is well mixed, so the temperature inside is uniform, but that does not make it isothermal. Isothermal operation holds only when the feed temperature equals the reactor temperature. The stirrer work $\dot{W}_s$ is negative because work done by the system is defined as positive.
열교환기는 열전달 유체가 $T_{a1}$로 들어가 $T_{a2}$로 나오는 구조로 모델링한다. 유체 쪽 축적을 무시하는 quasi-steady state 가정에서 전달 열은 아래 식으로 주어진다. 유체 유량이 매우 크면 $T_{a1} \approx T_{a2} = T_a$이고 식은 $UA(T_a - T)$로 단순해진다.The heat exchanger is modeled with the heat-transfer fluid entering at $T_{a1}$ and leaving at $T_{a2}$. Assuming a quasi-steady state with no accumulation in the fluid, the transferred heat is given below. When the fluid flow rate is very large, $T_{a1} \approx T_{a2} = T_a$ and the expression reduces to $UA(T_a - T)$.
풀이는 두 식의 교점을 찾는 문제이다. 몰 수지에서 $X_{MB}(T)$를, 에너지 수지에서 $X_{EB}(T)$를 구해 같은 그래프에 그리면 교점이 정상상태의 $X$와 $T$이다. Example 12-3은 propylene oxide의 가수분해를 300 gal 단열 CSTR에서 하는 문제이다. 교점은 전환율 약 0.84, 온도 약 340 K(153 °F)이며, 이는 증기 손실을 막기 위한 상한 125 °F를 넘는다. 따라서 이 반응기를 냉각 없이 쓸 수 없고, Example 12-4에서 냉각 코일을 넣는다.Solving the problem means finding the intersection of two equations. Plotting $X_{MB}(T)$ from the mole balance and $X_{EB}(T)$ from the energy balance on one graph, the intersection gives the steady-state $X$ and $T$. Example 12-3 hydrolyzes propylene oxide in a 300 gal adiabatic CSTR. The intersection is a conversion of about 0.84 at about 340 K (153 °F), above the 125 °F limit set to avoid vapor loss. The reactor therefore cannot be used without cooling, and Example 12-4 adds a cooling coil.
$X_{MB}(T)$: 속도식과 CSTR 몰 수지에서 나온 S자 곡선이다. 일차 반응에서는 $\tau k/(1+\tau k)$이고, $\tau$가 커지면 왼쪽으로 이동한다.$X_{MB}(T)$: the S-shaped curve from the rate law and the CSTR mole balance. For a first-order reaction it is $\tau k/(1+\tau k)$, and it shifts left as $\tau$ increases.
$X_{EB}(T)$: 에너지 수지에서 나온 직선이다. 단열이면 기울기가 $C_{P0}/(-\Delta H_{Rx})$이고 $T_0$에서 $X = 0$을 지난다.$X_{EB}(T)$: the straight line from the energy balance. For adiabatic operation its slope is $C_{P0}/(-\Delta H_{Rx})$ and it crosses $X = 0$ at $T_0$.
교점이 여러 개일 수 있다: S자 곡선과 직선은 한 번 이상 만난다. 어느 해가 실제로 나오는지는 12.5절에서 다룬다. 비선형 방정식 solver는 초기 추정에 따라 한 해만 주므로 그래프로 확인해야 한다.There can be more than one intersection: an S-curve and a line can meet more than once. Which solution is realized is the subject of Section 12.5. A nonlinear solver returns one root depending on the initial guess, so check graphically.
Figure 12.4단열 CSTR의 $X_{MB}$와 $X_{EB}$ 교점Intersection of $X_{MB}$ and $X_{EB}$ in an Adiabatic CSTR
공간시간 $\tau$ (h)Space time $\tau$ (h)0.123
공급 온도 $T_0$ (K)Feed temperature $T_0$ (K)297.0 K
전환율 $X$Conversion $X$0
반응기 온도 (K)Reactor T (K)0
125 °F 상한 대비vs 125 °F limit-
기본값($\tau = 0.123$ h, $T_0 = 297$ K)에서는 교점이 약 340 K에 있어 125 °F(325 K)를 넘는다. $\tau$를 줄이거나 $T_0$를 낮추면 온도가 상한 아래로 내려오지만 전환율도 함께 내려간다. Example 12-3의 값($E = 32\,400$ Btu/lbmol, $\Delta H_{Rx} = -36\,400$ Btu/lbmol, $\sum\Theta_i C_{P_i} = 403$ Btu/(lbmol °F))을 SI로 환산했고, $\Delta C_P$ 보정은 무시했다.At the defaults ($\tau = 0.123$ h, $T_0 = 297$ K) the intersection is near 340 K, above 125 °F (325 K). Reducing $\tau$ or lowering $T_0$ brings the temperature under the limit, but the conversion drops with it. The calculation converts the Example 12-3 data ($E = 32{,}400$ Btu/lbmol, $\Delta H_{Rx} = -36{,}400$ Btu/lbmol, $\sum\Theta_i C_{P_i} = 403$ Btu/(lbmol °F)) to SI units and neglects the $\Delta C_P$ correction.
Section 12.5
다중 정상상태Multiple Steady States (MSS)
CSTR의 에너지 수지를 열 제거항 $R(T)$와 열 생성항 $G(T)$로 나누어 쓰면, 두 곡선의 교점이 정상상태이다. $R(T)$는 $T$에 대해 선형이고 기울기가 $C_{P0}(1+\kappa)$이다. 공급 온도 $T_0$를 올리면 기울기는 그대로 두고 직선이 오른쪽으로 이동하며, 열교환 면적 $A$를 키우면 기울기가 커진다.Writing the CSTR energy balance as a heat-removed term $R(T)$ and a heat-generated term $G(T)$, each intersection is a steady state. $R(T)$ is linear in $T$ with slope $C_{P0}(1+\kappa)$. Raising the feed temperature $T_0$ shifts the line to the right at the same slope, and a larger exchange area $A$ steepens it.
$G(T)$는 S자 곡선이다. 저온에서는 $k$가 작아 열 생성이 지수적으로 작고, 고온에서는 전환이 거의 완결되어 $-\Delta H_{Rx}$ 근처에서 포화한다. 직선이 이 곡선과 세 번 만나면 정상상태가 셋이다. $T_0$가 낮을 때는 낮은 온도의 교점 하나이고, $T_0$를 올려 가면 어느 값에서 세 교점이 생기며, 더 올리면 높은 온도의 교점 하나만 남는다.$G(T)$ is an S-shaped curve. At low temperature $k$ is small and heat generation is exponentially small, and at high temperature conversion is nearly complete so $G$ saturates near $-\Delta H_{Rx}$. When the line meets the curve three times there are three steady states. At low $T_0$ there is a single low-temperature intersection; as $T_0$ rises, three appear at some value, and beyond a higher value only the high-temperature intersection remains.
$T_0$를 올리면서 반응기 온도 $T_s$를 그리면 ignition-extinction curve가 된다. 낮은 분기에서 $T_0$를 올리면 점화 온도(ignition temperature)에서 $T_s$가 높은 분기로 불연속적으로 올라간다. 높은 분기에서 $T_0$를 내리면 더 낮은 소화 온도(extinction temperature)에서 $T_s$가 낮은 분기로 떨어진다. 점화와 소화 온도가 다르므로 반응기 상태가 이력(hysteresis)에 의존한다.Plotting the reactor temperature $T_s$ against $T_0$ gives the ignition-extinction curve. Raising $T_0$ on the low branch, $T_s$ jumps discontinuously to the high branch at the ignition temperature. Lowering $T_0$ on the high branch, $T_s$ drops to the low branch at a lower extinction temperature. Because the two temperatures differ, the reactor state depends on its history (hysteresis).
가운데 정상상태는 불안정하다. 이 상태에서 온도가 조금 올라가면 $G > R$이어서 계속 올라 높은 정상상태에 이르고, 조금 내려가면 $R > G$여서 낮은 정상상태로 내려간다. 안정 조건은 교점에서 $dG/dT < dR/dT$이다. 높은 정상상태도 국소적으로만 안정하다. 큰 섭동이 오면 낮은 정상상태로 떨어질 수 있다. Vejtasa와 Schmitz는 단열 CSTR에서 유량을 바꾸며 이런 다중 정상상태를 실험으로 확인했다.The middle steady state is unstable. A small rise in temperature there gives $G > R$ and the temperature keeps climbing to the upper steady state, whereas a small drop gives $R > G$ and it falls to the lower one. The stability condition at an intersection is $dG/dT < dR/dT$. The upper state is only locally stable, and a large disturbance can drop the reactor to the lower state. Vejtasa and Schmitz confirmed such multiple steady states experimentally in an adiabatic CSTR by varying the flow rate.
점화 온도(ignition temperature): 낮은 분기에서 $T_0$를 올릴 때 $T_s$가 높은 분기로 올라가는 공급 온도이다. $R$ 직선이 $G$의 낮은 온도 쪽 부분에 접하는 지점이다.Ignition temperature: the feed temperature at which $T_s$ jumps to the high branch as $T_0$ is raised on the low branch. It is where the $R$ line becomes tangent to the lower part of $G$.
소화 온도(extinction temperature): 높은 분기에서 $T_0$를 내릴 때 $T_s$가 낮은 분기로 떨어지는 공급 온도이다. 점화 온도보다 낮다.Extinction temperature: the feed temperature at which $T_s$ drops to the low branch as $T_0$ is lowered on the high branch. It is lower than the ignition temperature.
안정과 불안정: 온도 섭동 뒤에 원래 상태로 돌아오면 안정이다. 세 교점 중 위와 아래는 국소 안정, 가운데는 불안정이다.Stable and unstable: a state is stable if the reactor returns to it after a temperature disturbance. Of three intersections, the upper and lower are locally stable and the middle is unstable.
Figure 12.5G(T)와 R(T)의 교점, 점화와 소화 온도Intersections of G(T) and R(T), Ignition and Extinction Temperatures
예측: 공급 온도 $T_0$를 낮은 값에서 천천히 올릴 때 반응기 온도 $T_s$는 어떻게 변할까?Predict: as the feed temperature $T_0$ is raised slowly from a low value, how does the reactor temperature $T_s$ change?
목표: 위쪽 그림에서 빨간 직선을 좌우로 끌어 $T_0$를 올려 반응기를 점화시키고, 점화가 기록되면 $T_0$를 내려 소화시키세요. 두 온도가 모두 기록되면 완료입니다. 미세 조정에는 아래 버튼을 쓰세요.Goal: drag the red line in the upper plot sideways to raise $T_0$ until the reactor ignites, then lower $T_0$ until it extinguishes. The goal is complete when both temperatures are recorded. Use the buttons below for fine steps.
공급 온도 $T_0$ (K)Feed $T_0$ (K)0
정상상태 개수Steady states1
반응기 온도 $T_s$ (K)Reactor $T_s$ (K)0
기록된 점화 $T_0$ (K)Recorded ignition $T_0$ (K)-
기록된 소화 $T_0$ (K)Recorded extinction $T_0$ (K)-
아래 그림의 파란 실선은 안정한 정상상태, 빨간 점선은 불안정한 정상상태이다. 점화는 낮은 분기가 사라지는 $T_0$에서, 소화는 높은 분기가 사라지는 $T_0$에서 일어나며 두 값이 다르다. 일차 비가역 액상 반응, $-\Delta H_{Rx} = 50$ kJ/mol, $C_{P0} = 250$ J/(mol K), $E = 60$ kJ/mol, $\kappa = 0.5$, $T_a = 300$ K로 12.5절 식을 계산했다. 수치는 설명용이며 교재 예제 값이 아니다.In the lower plot the solid blue lines are stable steady states and the dashed red line is the unstable one. Ignition occurs at the $T_0$ where the low branch disappears, extinction where the high branch disappears, and the two values differ. The Section 12.5 equations are evaluated for a first-order irreversible liquid-phase reaction with $-\Delta H_{Rx} = 50$ kJ/mol, $C_{P0} = 250$ J/(mol K), $E = 60$ kJ/mol, $\kappa = 0.5$, $T_a = 300$ K. The values are illustrative, not textbook example data.
Section 12.6
비등온 다중 반응Nonisothermal Multiple Chemical Reactions
실제 반응계는 대부분 반응이 둘 이상이고 등온이 아니다. 이 절은 앞의 모든 장을 합쳐 다중 반응의 몰 수지, 속도식, 에너지 수지를 함께 푸는 방법을 보인다. PFR의 에너지 수지는 단일 반응식에서 반응열 항 하나를 반응 $i$ 전체에 대한 합으로 바꾼 형태이다. $r_{ij}$는 반응 $i$에서 화학종 $j$의 생성 속도이고, $\Delta H_{Rx,ij}$는 같은 반응의 화학종 $j$ 기준 반응열이다.Most real reacting systems involve more than one reaction and are not isothermal. This section combines all the earlier chapters to solve mole balances, rate laws, and the energy balance together for multiple reactions. The PFR energy balance replaces the single heat-of-reaction term with a sum over reactions $i$. Here $r_{ij}$ is the formation rate of species $j$ in reaction $i$, and $\Delta H_{Rx,ij}$ is the heat of that reaction per mole of species $j$.
병렬 반응(Example 12-5)에서는 반응물이 약 0.45 dm³에서 거의 소모되고, 그 지점부터 $Q_r > Q_g$가 되어 온도가 내려가며 selectivity는 더 변하지 않는다. selectivity를 높이려면 반응기를 0.3 dm³ 정도로 짧게 해야 한다. 직렬 반응을 CSTR에서 하는 Example 12-6은 정상상태가 다섯 개이며, 1, 3, 5번이 안정하고 2, 4번이 불안정하다. 이 중 5번 상태는 selectivity가 너무 낮아 쓸 수 없다.In the parallel reactions of Example 12-5 the reactant is nearly consumed by about 0.45 dm³, after which $Q_r > Q_g$, the temperature falls, and the selectivity stops changing. A higher selectivity requires shortening the reactor to about 0.3 dm³. Example 12-6, series reactions in a CSTR, has five steady states, of which states 1, 3, and 5 are stable and 2 and 4 are unstable. State 5 has too low a selectivity to be useful.
복합 반응을 PFR에서 하는 Example 12-7은 냉각 방식에 따른 최고 온도를 비교한다. 최고 온도는 co-current 930 K, countercurrent 1100 K, $T_a$ 일정 870 K이고 단열이 가장 높다. 부반응이 일어나는 온도를 피하려면 냉각수 유량을 크게 해 $T_a$를 일정하게 유지하는 쪽이 낫다. 이 예제의 안전 한계는 750 K이며 네 방식 모두 이를 넘는다.Example 12-7, complex reactions in a PFR, compares the peak temperature for different cooling schemes. The peak is 930 K for co-current, 1100 K for countercurrent, and 870 K for constant $T_a$, and the adiabatic case is highest. To avoid temperatures where side reactions occur, a high coolant flow that keeps $T_a$ constant is preferable. The safety limit in this example is 750 K, and all four schemes exceed it.
반응 $i$의 열 기여: 각 반응이 자기 반응열과 자기 속도의 곱만큼 열을 낸다. 반응마다 활성화 에너지가 다르므로 온도가 오르면 활성화 에너지가 큰 반응이 상대적으로 빨라진다.Heat contribution of reaction $i$: each reaction releases heat equal to its own heat of reaction times its own rate. Because activation energies differ, a higher temperature favors the reaction with the larger activation energy.
온도와 selectivity: 원하는 반응과 부반응의 활성화 에너지가 다르면 최고 온도가 selectivity를 정한다. 그래서 hot spot 온도 제한이 수율 문제가 된다.Temperature and selectivity: when the desired and side reactions have different activation energies, the peak temperature sets the selectivity. A hot-spot limit is therefore also a yield issue.
다중 반응 CSTR의 다중 정상상태: 반응이 둘 이상이면 정상상태가 셋을 넘을 수 있다. 어느 정상상태에서 운전하는지가 selectivity를 정한다.Multiple steady states in multi-reaction CSTRs: with two or more reactions there can be more than three steady states, and the operating state determines the selectivity.
Section 12.7 and 12.8
반경 방향과 축 방향 변화, 반응기 안전Radial and Axial Variations, and Reactor Safety
지금까지는 속도, 농도, 온도, 반응 속도가 반경 방향으로 변하지 않는다고 보고 ODE solver로 축 방향 프로파일만 구했다. 반경 방향 변화까지 포함하면 원통형 환형 부피(두께 $\Delta r$, 길이 $\Delta z$, 부피 $2\pi r\,\Delta r\,\Delta z$)에서 몰 수지와 에너지 수지를 세우고 PDE solver(예: COMSOL)로 $C(r, z)$와 $T(r, z)$를 구한다. 몰 flux는 확산 성분과 대류 성분으로, 에너지 flux는 전도 성분 $q_r = -k_e\,\partial T/\partial r$과 대류 성분으로 이루어진다.So far velocity, concentration, temperature, and rate were taken as uniform across the radius, and only axial profiles were found with an ODE solver. Including radial variation requires mole and energy balances on a cylindrical annulus (thickness $\Delta r$, length $\Delta z$, volume $2\pi r\,\Delta r\,\Delta z$) and a PDE solver such as COMSOL to obtain $C(r, z)$ and $T(r, z)$. The molar flux has diffusive and convective parts, and the energy flux has a conduction part $q_r = -k_e\,\partial T/\partial r$ and a convective part.
냉각 재킷이 있는 관(Example W12-8)에서는 관벽 쪽 온도가 낮아 반응 속도가 느리다. 그러나 벽 바로 옆 유속은 마찰 때문에 거의 0이어서 체류 시간이 길고, 그 결과 벽 가까이에서 전환율이 다시 올라간다. 평균 온도만 보는 PFR 모델로는 이 분포를 얻을 수 없다.In a tube with a cooling jacket (Example W12-8) the temperature near the wall is low and the rate is slow. The velocity right next to the wall, however, is almost zero because of friction, so the residence time is long and the conversion rises again close to the wall. A PFR model that tracks only the mean temperature cannot show this distribution.
발열 반응을 키울 때는 사고 사례를 함께 봐야 한다. 폭주 반응(runaway reaction)은 반응기 운전에서 가장 위험한 경우이다. 냉각이 줄어 $R(T)$의 기울기가 작아지면 낮은 정상상태가 사라지거나, 온도가 가운데 불안정 정상상태를 넘어 높은 정상상태로 올라간다. 2007년 T2 Laboratories 폭발은 이런 폭주 반응의 사례로, Chapter 13에서 CSI 방식으로 분석한다. 반응 위험성 평가에는 ARSST 같은 장비와 CCPS, SAChE 자료를 쓴다.When scaling up an exothermic reaction, accident case histories should be studied alongside. A runaway reaction is the most dangerous situation in reactor operation. When cooling is reduced and the slope of $R(T)$ falls, the low steady state can disappear, or the temperature can pass the unstable middle state and climb to the high one. The 2007 explosion at T2 Laboratories is such a runaway case, analyzed in Chapter 13 in the CSI format. Reactivity hazards are assessed with equipment such as the ARSST and with CCPS and SAChE resources.
유효 열전도도 $k_e$: 반경 방향 열 전달을 하나의 계수로 나타낸 값이다. 위 식은 축 방향 전도를 무시한 단순화 형태이다.Effective thermal conductivity $k_e$: a single coefficient for radial heat transfer. The equation above is a simplified form that neglects axial conduction.
폭주(runaway)의 조건: 열 생성이 열 제거보다 온도에 더 민감하게 증가하면($dG/dT > dR/dT$) 온도가 계속 올라 되돌릴 수 없다. 12.5절의 불안정 정상상태가 그 경계이다.Runaway condition: if heat generation grows faster with temperature than heat removal ($dG/dT > dR/dT$), the temperature cannot return. The unstable steady state of Section 12.5 is the boundary.
Figure 12.6냉각 중단 후 복구 시점과 폭주 반응Cooling Interruption, Recovery Timing, and Runaway
예측: 냉각을 잠시 중단했다가 복구하면 CSTR은 언제나 원래의 낮은 온도로 돌아올까?Predict: if cooling is interrupted briefly and then restored, will the CSTR always return to its original low temperature?
목표: 냉각 중단 버튼을 눌러 온도를 올리고, 온도가 불안정 정상상태(점선)보다 12 K 이내로 낮을 때 냉각 복구 버튼을 눌러 반응기를 낮은 상태로 되돌리세요.Goal: press the cooling-interrupt button to let the temperature rise, and when it is within 12 K below the unstable steady state (dashed line), press the restore button to return the reactor to the low state.
반응기 온도 (K)Reactor T (K)0
되돌릴 수 없는 온도 (K)Point of no return (K)0
냉각CoolingON
상태Status-
냉각을 중단하면 $\kappa = 0$이 되어 $R(T)$의 기울기가 작아지고 $G > R$이므로 온도가 계속 올라간다. 냉각을 복구해도 온도가 가운데 불안정 정상상태를 이미 넘었다면 $G > R$이어서 높은 정상상태까지 올라간다. 12.5절과 같은 모델에서 $T_0 = 330$ K, 냉각 시 $\kappa = 0.5$를 쓰고, 시간은 설명을 위해 축소한 값이다.Interrupting cooling sets $\kappa = 0$, so the slope of $R(T)$ drops, $G > R$, and the temperature keeps rising. If cooling is restored after the temperature has passed the unstable middle state, $G > R$ still holds and the temperature climbs to the high steady state. The model is the one of Section 12.5 with $T_0 = 330$ K and $\kappa = 0.5$ when cooled, and the time scale is compressed for illustration.
Self-Check
확인 문제Quiz
Q1. 열교환이 있는 발열 PFR에서 반응기 온도가 최고가 되는 지점은 어디인가?Q1. Where does the temperature reach its maximum in an exothermic PFR with heat exchange?
$dT/dV = (Q_g - Q_r)/\sum F_i C_{P_i}$이므로 온도의 극대는 $Q_g = Q_r$에서 생긴다. 입구 쪽에서는 $Q_g > Q_r$로 온도가 오르고, 반응물이 소모되어 $Q_g$가 줄면 $Q_r > Q_g$가 되어 온도가 내려간다. $T = T_a$인 지점에서는 $Q_r = 0$이므로 $Q_g > 0$이면 온도가 계속 오른다.Since $dT/dV = (Q_g - Q_r)/\sum F_i C_{P_i}$, the temperature maximum occurs at $Q_g = Q_r$. Near the inlet $Q_g > Q_r$ and the temperature rises; once the reactant is consumed and $Q_g$ declines, $Q_r > Q_g$ and the temperature falls. At $T = T_a$ we have $Q_r = 0$, so the temperature keeps rising if $Q_g > 0$.
Q2. Example 12-7에서 최고 온도가 가장 낮은 냉각 방식은 무엇인가?Q2. In Example 12-7, which cooling scheme gives the lowest peak temperature?
냉각수 유량이 충분히 커서 $T_a$가 일정하면 냉각이 가장 효과적이어서 최고 온도가 870 K로 가장 낮다. countercurrent는 뜨거워진 냉각수가 반응이 빠른 입구 쪽에 닿아 1100 K까지 올라간다. 단열은 냉각이 없으므로 출구 온도가 가장 높다.When the coolant flow is large enough that $T_a$ is constant, cooling is most effective and the peak is lowest at 870 K. In countercurrent flow the warmed coolant reaches the fast-reacting inlet end and the peak rises to 1100 K. Adiabatic operation has no cooling, so its exit temperature is highest.
Q3. CSTR의 세 정상상태 중 가운데 상태가 불안정한 이유는 무엇인가?Q3. Why is the middle of the three CSTR steady states unstable?
가운데 교점에서 온도가 조금 오르면 $G > R$이어서 온도가 더 오르고, 조금 내리면 $R > G$여서 더 내린다. 즉 섭동이 커진다. 안정 조건은 $dG/dT < dR/dT$이다. 접하는 점은 두 정상상태가 합쳐지는 점화 또는 소화 온도이다.At the middle intersection a small rise gives $G > R$, so the temperature rises further, and a small drop gives $R > G$, so it falls further. The disturbance grows. The stability condition is $dG/dT < dR/dT$. Tangency marks the ignition or extinction temperature where two steady states merge.
What If?
만약에?What If?
발열 PFR에서 냉각수 유량을 한없이 키우면?What if the coolant flow in an exothermic PFR is made very large?
클릭하여 확인 →Click to reveal →
$\dot{m}_c C_{P_c} \to \infty$이면 $dT_a/dV \to 0$이므로 $T_a$가 일정해지고 co-current와 countercurrent의 차이가 사라진다. Example 12-7에서 $T_a$ 일정 조건의 최고 온도가 870 K로 가장 낮았다. 다만 유량을 키우면 펌프 동력과 배관 비용이 늘어난다.As $\dot{m}_c C_{P_c} \to \infty$, $dT_a/dV \to 0$, so $T_a$ is constant and the difference between co-current and countercurrent disappears. In Example 12-7 the constant-$T_a$ case had the lowest peak, 870 K. A larger flow, however, raises pumping power and piping cost.
열교환 면적 $A$를 키우면 CSTR의 다중 정상상태는 어떻게 되는가?What happens to CSTR multiple steady states if the exchange area $A$ is increased?
클릭하여 확인 →Click to reveal →
$\kappa = UA/(F_{A0}C_{P0})$가 커지면 $R(T)$의 기울기 $C_{P0}(1+\kappa)$가 커진다. 기울기가 $G(T)$의 최대 기울기보다 커지면 직선이 곡선과 한 번만 만나 다중 정상상태가 사라진다. 점화와 소화 온도 사이의 이력 구간도 함께 사라진다.A larger $\kappa = UA/(F_{A0}C_{P0})$ steepens $R(T)$, whose slope is $C_{P0}(1+\kappa)$. When the slope exceeds the maximum slope of $G(T)$, the line meets the curve only once and multiple steady states disappear. The hysteresis interval between ignition and extinction disappears with them.
흡열 반응기를 단열로 길게 만들면?What if an endothermic reactor is made long and adiabatic?
클릭하여 확인 →Click to reveal →
온도가 계속 내려가 $k$가 지수적으로 줄고 반응이 사실상 멈춘다. 아세톤 분해에서 1 dm³ 관의 단열 전환율은 약 0.20이고, 부피를 5 dm³로 늘려도 0.28에 그친다. 반응기를 길게 하는 것보다 열을 공급하는 것이 먼저이다.The temperature keeps falling, $k$ decays exponentially, and the reaction effectively stops. For acetone cracking the adiabatic conversion in a 1 dm³ tube is about 0.20, and even 5 dm³ gives only 0.28. Supplying heat comes before lengthening the reactor.
높은 정상상태에서 운전 중인 CSTR의 공급 온도를 점화 온도 아래로 내리면?What if the feed of a CSTR running on the high steady state is cooled below the ignition temperature?
클릭하여 확인 →Click to reveal →
반응기는 높은 분기에 머문다. 높은 분기는 점화 온도가 아니라 더 낮은 소화 온도에서 사라지기 때문이다. 이 이력 때문에 같은 공급 온도에서도 과거의 운전 이력에 따라 반응기가 높은 온도 또는 낮은 온도에 있을 수 있다.The reactor stays on the high branch, because that branch disappears at the lower extinction temperature, not at the ignition temperature. Because of this hysteresis, at the same feed temperature the reactor can be hot or cold depending on its past operation.
Key Takeaways
01
열 생성과 열 제거의 비교Compare Heat Generated and Removed
PFR의 온도 기울기는 $(Q_g - Q_r)/\sum F_i C_{P_i}$이다. $Q_g = Q_r$인 지점에서 hot spot이 생기고, 에너지 수지는 알고리즘의 다섯 번째 요소로 몰 수지와 함께 푼다.The PFR temperature gradient is $(Q_g - Q_r)/\sum F_i C_{P_i}$. The hot spot appears where $Q_g = Q_r$, and the energy balance is the fifth building block solved together with the mole balance.
02
냉각수 방향과 $T_a$Coolant Direction and $T_a$
co-current와 countercurrent는 부호만 다른 $dT_a/dV$를 쓰고, countercurrent는 반복 계산이 필요하다. 냉각수 유량이 크면 $T_a$가 일정해져 hot spot이 가장 낮아진다.Co-current and countercurrent use $dT_a/dV$ with opposite signs, and countercurrent needs iteration. A large coolant flow makes $T_a$ constant and gives the lowest hot spot.
03
CSTR의 G(T)와 R(T)G(T) and R(T) of a CSTR
두 곡선의 교점이 정상상태이다. 교점이 셋이면 가운데는 불안정하고, 점화 온도와 소화 온도가 달라 이력이 생긴다.Intersections of the two curves are steady states. With three, the middle one is unstable, and different ignition and extinction temperatures create hysteresis.
04
다중 반응과 안전Multiple Reactions and Safety
다중 반응에서는 반응마다 열 항을 더하고, 최고 온도가 selectivity와 안전 한계를 함께 정한다. 냉각 상실 시 불안정 정상상태를 넘기 전에 복구해야 폭주를 피한다.For multiple reactions the heat terms are summed, and the peak temperature sets both selectivity and the safety margin. After a loss of cooling, restoring it before the unstable steady state is passed avoids runaway.