비등온 반응기 설계: 정상상태 에너지 수지와 단열 PFRNonisothermal Reactor Design: The Steady-State Energy Balance and Adiabatic PFR
Fogler, Elements of Chemical Reaction Engineering, Chapter 11. 슬라이더를 움직이면 그래프가 실시간으로 바뀐다.Fogler, Elements of Chemical Reaction Engineering, Chapter 11. Move the sliders to see the graphs respond in real time.
에너지 수지반응열 $\Delta H_{Rx}(T)$단열 PFR단열 평형 전환율단 사이 냉각최적 공급 온도
Section 11.1
비등온 설계가 필요한 이유Rationale
지금까지 반응기 설계는 온도가 일정하다고 가정했다. 그러나 산업 반응의 대부분은 반응열을 내거나 흡수하므로 반응기 안에서 온도가 변한다. 단열 PFR에서 발열 반응이 진행되면 전환율이 올라갈수록 온도가 올라가고, 비속도 상수 $k$는 Arrhenius 식에 따라 온도와 함께 바뀐다.Reactor design so far assumed constant temperature. Most industrial reactions release or absorb heat, so the temperature changes inside the reactor. In an adiabatic PFR with an exothermic reaction, temperature rises with conversion, and the rate constant $k$ changes with temperature through the Arrhenius equation.
몰 수지와 속도식, 화학량론을 결합해도 $X$와 $T$가 모두 미지수로 남는다. 따라서 CRE 알고리즘에 에너지 수지를 다섯째 단계로 더해 $T$를 $X$의 함수로 구해야 한다. 이 장은 정상상태 에너지 수지를 세우고, 이를 단열 PFR, 단열 평형 전환율, 단 사이 냉각, 최적 공급 온도에 적용한다.Combining the mole balance, rate law and stoichiometry still leaves both $X$ and $T$ unknown. The energy balance is therefore added as a fifth step of the CRE algorithm so that $T$ can be written as a function of $X$. This chapter builds the steady-state energy balance and applies it to adiabatic PFRs, adiabatic equilibrium conversion, interstage cooling and the optimum feed temperature.
비등온 알고리즘: 몰 수지, 속도식, 화학량론의 결합에 에너지 수지를 더해 $X$와 $T$를 함께 푼다.Nonisothermal algorithm: add the energy balance to the mole balance, rate law, stoichiometry and combine step, and solve $X$ and $T$ together.
단열 운전: 열교환이 없어 $\dot Q = 0$이다. 발열 반응이면 온도가 올라가고 흡열 반응이면 내려간다.Adiabatic operation: no heat exchange, $\dot Q = 0$. Temperature rises for exothermic and falls for endothermic reactions.
단열 온도 변화 $\Delta T_{ad}$ (X=1)Adiabatic rise $\Delta T_{ad}$ (X=1)40 K
활성화 에너지 $E$Activation energy $E$60 kJ/mol
등온 X (s=3)Isothermal X (s=3)0
단열 X (s=3)Adiabatic X (s=3)0
단열 출구 TAdiabatic exit T0
1차 비가역 반응 $dX/ds = k(T)/k(T_0)\,(1-X)$를 풀었다. $s = k(T_0)\tau$이고 $T = T_0 + \Delta T_{ad}X$이다. $E$와 $\Delta T_{ad}$는 교재 Example 11-1의 정성적 상황을 보이려고 고른 예시 값이다. $\Delta T_{ad}$를 음수로 두면 흡열 반응이 되어 단열 전환율이 등온보다 느리게 오른다.First-order irreversible reaction, $dX/ds = k(T)/k(T_0)\,(1-X)$ with $s = k(T_0)\tau$ and $T = T_0 + \Delta T_{ad}X$. $E$ and $\Delta T_{ad}$ are illustrative values chosen to show the qualitative situation of Example 11-1. A negative $\Delta T_{ad}$ represents an endothermic reaction, where adiabatic conversion rises more slowly than isothermal.
Section 11.2
에너지 수지The Energy Balance
열역학 제1법칙을 열린계에 적용하면 계의 에너지 변화율은 열 유입, 일 유출, 유입 및 유출 물질이 실어 나르는 에너지의 차와 같다. 정상상태에서는 계의 에너지 변화율이 0이다.Applying the first law of thermodynamics to an open system, the rate of change of system energy equals the heat added, minus the work done by the system, plus the net energy carried by streams entering and leaving. At steady state the accumulation is zero.
일 $\dot W$는 축일 $\dot W_s$와 유동일로 나뉜다. 유동일은 물질을 계에 밀어 넣고 내보내는 데 드는 $PV$ 일이다. 유동일을 내부에너지 항에 합치면 내부에너지가 엔탈피 $H_i$로 바뀐다. 이렇게 얻은 식이 정상상태 에너지 수지이다.The work $\dot W$ splits into shaft work $\dot W_s$ and flow work, the $PV$ work of pushing material into and out of the system. Adding flow work to the internal-energy terms turns internal energy into enthalpy $H_i$. The result is the steady-state energy balance.
축일 $\dot W_s$: 교반기나 압축기 같은 축을 통해 계가 하는 일이다. 대부분의 화학 반응기에서는 작아서 무시한다.Shaft work $\dot W_s$: work done by the system through a shaft, such as a stirrer or compressor. It is small in most chemical reactors and is neglected.
유동일: 유입 물질을 계에 밀어 넣고 유출 물질을 밀어내는 일이다. $E_i = U_i$에 더하면 $H_i = U_i + P\tilde V_i$가 된다.Flow work: the work of pushing inlet material in and outlet material out. Adding it to $E_i = U_i$ gives $H_i = U_i + P\tilde V_i$.
열 유입 $\dot Q$: 열교환기나 재킷으로 들어오는 열이다. 계가 열을 받으면 양수이다.Heat input $\dot Q$: heat entering through an exchanger or jacket. Positive when the system receives heat.
Section 11.3
사용하기 쉬운 형태의 에너지 수지The User-Friendly Energy Balance Equations
에너지 수지의 몰 유량을 $F_i = F_{A0}(\Theta_i + \nu_iX)$로, 엔탈피를 $H_i = H_i^\circ(T_R) + \int_{T_R}^{T} C_{Pi}\,dT$로 쓰면 식이 $X$와 $T$만의 식이 된다. 반응에 참여하는 모든 물질의 기준 온도 $T_R$에서의 생성 엔탈피를 화학량론 계수로 합한 값이 기준 온도의 반응열이다.Writing molar flow rates as $F_i = F_{A0}(\Theta_i + \nu_iX)$ and enthalpies as $H_i = H_i^\circ(T_R) + \int_{T_R}^{T} C_{Pi}\,dT$ turns the balance into an equation in $X$ and $T$ only. Summing the enthalpies of formation at the reference temperature $T_R$ with stoichiometric coefficients gives the heat of reaction at $T_R$.
반응열은 온도에 따라 달라진다. 생성물과 반응물의 열용량 차 $\Delta C_P$가 0이 아니면 $\Delta H_{Rx}(T)$는 온도에 대해 기울기 $\Delta C_P$인 직선으로 변한다. 예를 들어 N$_2$ + 3H$_2$ → 2NH$_3$의 25 °C 반응열은 NH$_3$ 1 mol당 -11,020 cal이고 N$_2$ 1 mol 기준으로는 -22,040 cal이다. $\Delta C_P$가 음수이므로 온도가 높아질수록 발열량이 커진다.The heat of reaction depends on temperature. When the heat capacity difference $\Delta C_P$ between products and reactants is nonzero, $\Delta H_{Rx}(T)$ varies linearly with slope $\Delta C_P$. For N$_2$ + 3H$_2$ → 2NH$_3$ the heat of reaction at 25 °C is -11,020 cal per mol NH$_3$, or -22,040 cal per mol N$_2$. Because $\Delta C_P$ is negative, the heat released grows as temperature rises.
$\Theta_i$: 기준 물질 A에 대한 공급 몰비이다. $\Theta_i = F_{i0}/F_{A0}$이고 불활성 물질도 포함한다.$\Theta_i$: feed mole ratio relative to the base species A, $\Theta_i = F_{i0}/F_{A0}$, including inerts.
$\Delta C_P = 0$인 경우: 반응열이 온도에 무관하다. 에너지 수지의 반응열 항이 $X\,\Delta H_{Rx}$ 하나로 단순해진다.The case $\Delta C_P = 0$: the heat of reaction is independent of temperature, and the reaction term collapses to $X\,\Delta H_{Rx}$.
Figure 11.2열용량에 따른 반응열 $\Delta H_{Rx}(T)$의 기울기Heat of Reaction vs. Temperature with Adjustable Heat Capacities
예측: N$_2$ + 3H$_2$ → 2NH$_3$의 온도를 298 K에서 700 K로 올리면 발열량 $|\Delta H_{Rx}|$는 어떻게 될까?Predict: if the temperature of N$_2$ + 3H$_2$ → 2NH$_3$ goes from 298 K to 700 K, what happens to the heat released $|\Delta H_{Rx}|$?
목표: 왼쪽 막대(N$_2$, H$_2$, NH$_3$의 $C_P$)를 위아래로 끌어 $|\Delta C_P| \le 0.75$ cal/(mol K)로 만드세요. 오른쪽 그림을 끌면 온도 표시선이 움직입니다.Goal: drag the left bars (the $C_P$ of N$_2$, H$_2$ and NH$_3$) up or down until $|\Delta C_P| \le 0.75$ cal/(mol K). Drag in the right plot to move the temperature marker.
$\Delta C_P$ (cal/mol K)0
표시선 TMarker T700 K
$\Delta H_{Rx}(T)$ (kcal/mol N$_2$)0
$\Delta H_{Rx}(298\,\mathrm{K}) = -22.04$ kcal/mol N$_2$는 교재 Example 11-2의 값이다. 초기 $C_P$ 6.96, 6.89, 8.52 cal/(mol K)는 298 K 부근의 일반적인 기체 열용량 근사값이고, 막대 범위 4부터 16까지는 조작을 위해 넓혔다. $\Delta C_P = 0$이면 반응열이 수평선이 되어 온도에 무관하다.$\Delta H_{Rx}(298\,\mathrm{K}) = -22.04$ kcal/mol N$_2$ is the value in Example 11-2. The initial $C_P$ values 6.96, 6.89 and 8.52 cal/(mol K) are typical gas heat capacities near 298 K, and the bar range 4 to 16 is widened for manipulation. When $\Delta C_P = 0$ the heat of reaction is a horizontal line, independent of temperature.
Section 11.4
단열 운전Adiabatic Operation
단열 반응기에서 $\dot Q = 0$이고 축일이 없으면 에너지 수지에서 $X$와 $T$의 관계가 바로 나온다. 이를 $X_{EB}$라 쓴다. 열용량 합이 반응 중 일정하고 $\Delta C_P = 0$이면 온도는 전환율에 대해 직선으로 올라간다. 직선의 기울기는 $(-\Delta H_{Rx})/\sum\Theta_iC_{Pi}$이다.With $\dot Q = 0$ and no shaft work, the energy balance gives a direct relation between $X$ and $T$, written $X_{EB}$. If the total heat capacity is constant and $\Delta C_P = 0$, temperature rises linearly with conversion, with slope $(-\Delta H_{Rx})/\sum\Theta_iC_{Pi}$.
단열 PFR 알고리즘은 다음 순서이다. 몰 수지 $dX/dV = -r_A/F_{A0}$, 속도식, 화학량론, 에너지 수지 $T(X)$를 결합해 $X$를 $V$에 대해 수치 적분한다. 각 $V$에서 $T$를 갱신하며 $k(T)$와 $K_C(T)$를 다시 계산한다. CSTR에는 미분 방정식이 없다. 같은 에너지 수지에서 $T(X)$를 정하고 $V = F_{A0}X/(-r_A)$에 대입해 대수식으로 푼다.The adiabatic PFR algorithm is as follows: combine the mole balance $dX/dV = -r_A/F_{A0}$, the rate law, stoichiometry and the energy balance $T(X)$, then integrate $X$ numerically along $V$. At each $V$, $T$ is updated and $k(T)$ and $K_C(T)$ are recomputed. A CSTR has no differential equation: use the same energy balance to fix $T(X)$ and substitute into $V = F_{A0}X/(-r_A)$ to solve algebraically.
Example 11-3은 n-부탄을 액상에서 단열로 이성질화한다. 가역 반응이므로 속도식에 $K_C$가 들어가고, $K_C$는 van't Hoff 식으로 온도에 따라 변한다.Example 11-3 isomerizes n-butane adiabatically in the liquid phase. The reaction is reversible, so the rate law contains $K_C$, which varies with temperature through the van't Hoff equation.
PFR 알고리즘: $dX/dV$ 하나만 적분하고 $T$는 에너지 수지의 대수식으로 구한다. ODE가 두 개로 늘지 않는다.PFR algorithm: integrate only $dX/dV$ and obtain $T$ from the algebraic energy balance. There is no second ODE.
불활성 물질: $\sum\Theta_iC_{Pi}$를 키워 같은 전환율에서의 온도 변화를 줄인다.Inert diluent: raises $\sum\Theta_iC_{Pi}$, which reduces the temperature change at a given conversion.
Figure 11.3n-부탄 이성질화 단열 PFR의 $X$, $X_e$, $T$ 분포Adiabatic n-Butane Isomerization PFR: X, X_e and T Profiles
공급 온도 $T_0$Feed temperature $T_0$330 K
i-펜탄 몰분율i-Pentane mole fraction10 %
반응기 부피 $V$Reactor volume $V$2.0 m3
X (V)0
T (V)0
Xe (T)0
X=0.7에 필요한 VV needed for X=0.70
Example 11-3의 자료로 계산했다. $\Delta H_{Rx} = -6900$ J/mol, $E = 65.7$ kJ/mol, $k = 31.1\ \mathrm{h}^{-1}$(360 K), $K_C = 3.03$(333 K), $C_{P,A} = C_{P,B} = 141$, $C_{P,i\text{-}P} = 161$ J/(mol K), $C_{A0} = 9.3$ kmol/m$^3$, 전체 공급 163 kmol/h로 $v_0 = 17.5$ m$^3$/h를 가정했다. 부피 $V$ 값은 이 가정에서 나온 값이라 교재 값과 다를 수 있다. $T_0$가 높으면 평형이 낮아져 70%에 도달하지 못한다.Computed with the Example 11-3 data: $\Delta H_{Rx} = -6900$ J/mol, $E = 65.7$ kJ/mol, $k = 31.1\ \mathrm{h}^{-1}$ at 360 K, $K_C = 3.03$ at 333 K, $C_{P,A} = C_{P,B} = 141$ and $C_{P,i\text{-}P} = 161$ J/(mol K), $C_{A0} = 9.3$ kmol/m$^3$, and total feed 163 kmol/h giving an assumed $v_0 = 17.5$ m$^3$/h. The volumes follow from this assumption and may differ from the book. A high $T_0$ lowers the equilibrium and 70% cannot be reached.
Section 11.5
단열 평형 전환율Adiabatic Equilibrium Conversion
가역 발열 반응의 평형 전환율 $X_e$는 온도가 올라갈수록 낮아진다. 단열 반응기에서는 반응이 진행되면 온도가 올라가 $X_e$가 다시 내려가므로, 반응기에서 얻을 수 있는 전환율에 상한이 생긴다. 이 상한은 에너지 수지 직선 $X_{EB}(T)$와 평형 곡선 $X_e(T)$가 만나는 점이다.For a reversible exothermic reaction, the equilibrium conversion $X_e$ falls as temperature rises. In an adiabatic reactor the temperature rises as reaction proceeds, pushing $X_e$ down, which puts an upper bound on attainable conversion. This bound is the intersection of the energy balance line $X_{EB}(T)$ and the equilibrium curve $X_e(T)$.
Example 11-4는 A ⇌ B에서 $\Delta H_{Rx} = -20{,}000$ cal/mol, $C_{PA} = C_{PB} = 50$ cal/(mol K), 298 K에서 $K_e = 10^5$이다. 순수한 A를 300 K로 공급하면 에너지 수지는 $T = 300 + 400X$가 된다. 두 곡선의 교점이 단열 평형 온도와 전환율이다. 교재는 그림에서 0.42와 465 K를 읽었고, 같은 식을 수치로 풀면 0.40과 460 K 근처이다.Example 11-4 uses A ⇌ B with $\Delta H_{Rx} = -20{,}000$ cal/mol, $C_{PA} = C_{PB} = 50$ cal/(mol K) and $K_e = 10^5$ at 298 K. Feeding pure A at 300 K gives the energy balance $T = 300 + 400X$. The intersection of the two curves is the adiabatic equilibrium temperature and conversion. The book reads 0.42 and 465 K from its graph; solving the same equations numerically gives about 0.40 and 460 K.
$X_e$가 경제성에 못 미치면 공급 온도를 낮추거나 불활성 물질을 넣는다. 둘 다 어려우면 반응기를 여러 단으로 나눈다. 유량은 $X_e$를 바꾸지 않는다.If $X_e$ is too low to be economical, lower the feed temperature or add inerts. If neither is possible, stage the reactors. Flow rate does not change $X_e$.
Figure 11.4X-T 평면의 평형 곡선과 단열선Equilibrium Curve and Adiabatic Line on the X-T Plane
예측: 이 발열 반응의 공급 온도 $T_0$를 낮추면 단열 평형 전환율은 어떻게 될까?Predict: if the feed temperature $T_0$ of this exothermic reaction is lowered, what happens to the adiabatic equilibrium conversion?
목표: 그림을 좌우로 끌어 입구 온도 $T_0$를 옮기고, 단열 평형 전환율 $X_e$를 0.45 이상으로 만드세요. 작은 점이 단열선을 따라 평형점까지 올라갑니다.Goal: drag the plot left or right to move the inlet temperature $T_0$ and bring the adiabatic equilibrium conversion $X_e$ to 0.45 or above. The small dot rides along the adiabatic line up to the equilibrium point.
$T_0$ (K)450
단열 평형 $X_e$Adiabatic $X_e$0
평형 온도 $T_e$ (K)Equilibrium $T_e$ (K)0
Example 11-4의 자료($\Delta H_{Rx} = -20{,}000$ cal/mol, $C_P = 50$ cal/(mol K), $K_e(298\,\mathrm{K}) = 10^5$)로 그렸다. $T_0$를 220 K까지 낮춰도 $X_e$는 0.57에 그치고 200 K에서도 0.61이다. 단열 반응기 한 대로는 0.8 이상을 얻을 수 없으므로 단 사이 냉각이 필요하다.Drawn with the Example 11-4 data ($\Delta H_{Rx} = -20{,}000$ cal/mol, $C_P = 50$ cal/(mol K), $K_e(298\,\mathrm{K}) = 10^5$). Even lowering $T_0$ to 220 K gives only $X_e$ = 0.57, and 0.61 at 200 K. A single adiabatic reactor cannot exceed 0.8, so interstage cooling is needed.
Section 11.6
반응기 단 나누기와 단 사이 냉각Reactor Staging with Interstage Cooling
발열 가역 반응에서 한 단의 단열 평형 전환율이 낮을 때는 반응기를 직렬로 여러 대 놓고 사이마다 냉각기를 둔다. 반응기에서는 $X$와 $T$가 단열선을 따라 함께 올라가고, 냉각기에서는 반응이 일어나지 않아 $X$는 그대로이고 $T$만 수평으로 내려간다. 냉각된 흐름이 다음 반응기에서 더 높은 평형 전환율을 갖는다.When a single stage has a low adiabatic equilibrium conversion for a reversible exothermic reaction, several reactors are placed in series with coolers between them. In a reactor, $X$ and $T$ rise together along the adiabatic line; in a cooler no reaction occurs, so $X$ stays constant and $T$ drops horizontally. The cooled stream has a higher equilibrium conversion in the next reactor.
Example 11-5는 Example 11-4의 반응을 각 반응기에서 평형 전환율의 95%까지 반응시키고, 냉각기 출구를 350 K로 한다. $F_{A0} = 40$ mol/s이면 460 K에서 350 K로 식힐 때 제거할 열은 $40 \times 50 \times 110 = 220$ kcal/s이다. 흡열 반응은 반대로 단 사이에서 가열해 낮아진 온도를 높인다.Example 11-5 reacts to 95% of the equilibrium conversion in each reactor, with coolers exiting at 350 K. For $F_{A0} = 40$ mol/s, cooling from 460 K to 350 K removes $40 \times 50 \times 110 = 220$ kcal/s. For endothermic reactions the interstage exchangers heat instead, restoring the temperature that dropped.
단열선: 각 반응기에서 기울기가 $1/400$ K$^{-1}$인 직선이다. 냉각 후 출발점만 왼쪽으로 옮겨진다.Adiabatic line: a straight line of slope $1/400$ K$^{-1}$ in each reactor. Only the starting point shifts left after cooling.
냉각 하한: 냉각수로 식힐 수 있는 온도에 한계가 있다. 이 그림에서는 300 K로 둔다.Cooling limit: the achievable cooling temperature is bounded by the cooling medium. This figure uses 300 K.
Figure 11.5단 사이 냉각 단 수와 도달 전환율Number of Cooled Stages vs. Reached Conversion
예측: 반응기 출구 흐름을 냉각기에 통과시키면 전환율 $X$는 어떻게 될까?Predict: when the reactor outlet stream passes through a cooler, what happens to the conversion $X$?
목표: 그림을 왼쪽으로 끌어 냉각 온도(300 K 이상)를 정하고 손을 떼면 단이 하나 늘어납니다. 가장 적은 단 수로 $X \ge 0.9$에 도달하세요. 각 반응기는 평형 전환율의 95%까지 반응합니다.Goal: drag the plot to the left to set the cooling temperature (at least 300 K) and release to add a stage. Reach $X \ge 0.9$ with the fewest stages. Each reactor reacts to 95% of its equilibrium conversion.
반응기 수Reactors1
현재 XCurrent X0
출구 온도 (K)Exit T (K)0
제거 열량 합 (kcal/s)Total heat removed (kcal/s)0
Example 11-4와 11-5의 반응으로, $F_{A0} = 40$ mol/s이고 $T_{in,1} = 300$ K이다. 단 수가 늘수록 $X$는 평형 곡선에 가까워지지만 마지막 단의 증가분은 작다. 매번 300 K까지 식히면 3단은 0.89, 4단은 0.95이므로 0.9 이상은 4단이 최소이다. 교재처럼 350 K로만 식히면 5단이 필요하다.Based on the reaction of Examples 11-4 and 11-5, with $F_{A0} = 40$ mol/s and $T_{in,1} = 300$ K. Each added stage moves $X$ closer to the equilibrium curve, but the last gains are small. Cooling to 300 K every time gives 0.89 for three stages and 0.95 for four, so four is the minimum for 0.9. Cooling only to 350 K as in the book needs five stages.
Section 11.7
최적 공급 온도Optimum Feed Temperature
크기나 촉매량이 정해진 단열 반응기에서 공급 온도 $T_0$를 바꾸면 출구 전환율이 어떻게 변하는지 본다. 가역 발열 반응에서 $T_0$가 매우 높으면 속도는 빠르지만 평형 전환율이 0에 가까워 생성물이 거의 없다. $T_0$가 매우 낮으면 평형 전환율은 높지만 속도가 느려 반응물이 거의 반응하지 못하고 나간다.Consider an adiabatic reactor of fixed size or catalyst mass and vary the feed temperature $T_0$. For a reversible exothermic reaction, a very high $T_0$ makes the rate fast but the equilibrium conversion nearly zero, so little product forms. A very low $T_0$ gives a high equilibrium conversion but the rate is so slow that reactant passes through unreacted.
따라서 출구 전환율을 최대로 하는 최적 $T_0$가 있다. $T_0$를 낮은 값에서 올리면 속도 증가로 전환율이 오르다가, 평형에 가까워지는 지점을 지나면 평형 전환율 감소 때문에 내려간다. 교재 그림 11-9에서 $T_0 = 600$ K는 입구 근처에서 평형에 도달해 0.15에 그치고, 500 K는 0.375, 350 K는 0.05이다.There is therefore an optimum $T_0$ that maximizes exit conversion. Raising $T_0$ from a low value increases conversion through a faster rate until equilibrium is approached; beyond that, the falling equilibrium conversion lowers it. In the book's Figure 11-9, $T_0 = 600$ K reaches equilibrium near the inlet and gives only 0.15, 500 K gives 0.375 and 350 K gives 0.05.
$$X_{EB}=\frac{C_{PR}\,(T-T_0)}{-\Delta H_{Rx}}=0.0075\,(T-T_0),\qquad R \rightleftharpoons S$$
높은 $T_0$: 입구에서 곧바로 평형에 닿고 전환율이 낮은 $X_e$를 넘지 못한다.High $T_0$: equilibrium is reached right at the inlet and conversion is limited to the low $X_e$.
낮은 $T_0$: $X_e$는 높지만 속도가 느려 주어진 촉매량으로는 평형에 이르지 못한다.Low $T_0$: $X_e$ is high but the rate is too slow to reach equilibrium with the given catalyst mass.
Figure 11.6공급 온도에 따른 단열 반응기 출구 전환율Exit Conversion of an Adiabatic Reactor vs. Feed Temperature
공급 온도 $T_0$Feed temperature $T_0$600 K
촉매량 배수Catalyst mass factor1.0
활성화 에너지 $E$Activation energy $E$40 kJ/mol
선택한 $T_0$의 출구 XExit X at chosen $T_0$0
최적 $T_0$ (K)Optimum $T_0$ (K)0
최대 출구 XMaximum exit X0
R ⇌ S는 1차 가역 반응이고 에너지 수지는 교재 식 $X_{EB} = 0.0075\,(T - T_0)$를 쓴다. 평형 곡선 $K_e = \exp(4654/T - 9.244)$는 교재 그림 11-9의 값(450 K에서 0.75, 620 K에서 0.15)에 맞춘 근사이고 550 K에서 교재보다 0.06 낮다. 속도 상수는 350 K에서 이 촉매량이 전환율 0.05를 주도록 보정했다. 교재와 정량적으로 같은 곡선은 아니고 모양을 재현한 것이다.R ⇌ S is a first-order reversible reaction with the book's energy balance $X_{EB} = 0.0075\,(T - T_0)$. The equilibrium curve $K_e = \exp(4654/T - 9.244)$ is a fit to the book's Figure 11-9 values (0.75 at 450 K, 0.15 at 620 K) and is about 0.06 below the book at 550 K. The rate constant is calibrated so that at 350 K this catalyst mass gives X = 0.05. The curves reproduce the shape, not the exact numbers, of the book.
Self-Check
확인 문제Quiz
Q1. A ⇌ B 반응($\Delta H_{Rx} = -20{,}000$ cal/mol, $C_{PA} = C_{PB} = 50$ cal/(mol K))의 순수 A를 300 K로 단열 공급한다. 전환율 0.5일 때 온도는?Q1. Pure A is fed adiabatically at 300 K for A ⇌ B ($\Delta H_{Rx} = -20{,}000$ cal/mol, $C_{PA} = C_{PB} = 50$ cal/(mol K)). What is the temperature at X = 0.5?
$T = T_0 + (-\Delta H_{Rx})X/C_{PA} = 300 + (20000/50)(0.5) = 500$ K이다. 단열 온도 변화는 전환율 1에서 400 K이다.$T = T_0 + (-\Delta H_{Rx})X/C_{PA} = 300 + (20000/50)(0.5) = 500$ K. The adiabatic temperature change at X = 1 is 400 K.
Q2. 단열 반응기에 가역 발열 반응이 일어날 때 공급 온도가 매우 높으면 출구 전환율이 낮은 이유는?Q2. Why is exit conversion low in an adiabatic reactor with a reversible exothermic reaction when the feed temperature is very high?
발열 반응의 $K_e$는 온도가 오를수록 작아진다. $T_0$가 높으면 속도는 빠르지만 입구 근처에서 곧바로 낮은 $X_e$에 닿아 더 진행되지 않는다. 단열 반응기이므로 열은 빠져나가지 않는다.$K_e$ of an exothermic reaction falls with temperature. A high $T_0$ gives a fast rate but equilibrium is reached near the inlet at a low $X_e$ and the reaction goes no further. The reactor is adiabatic, so no heat escapes.
Q3. 단 사이 냉각기 안에서 전환율과 온도는 어떻게 변하는가? (냉각기에서 반응은 일어나지 않는다)Q3. How do conversion and temperature change inside an interstage cooler? (No reaction occurs in the cooler.)
몰 유량이 변하지 않으므로 $X$는 그대로이고, 에너지 수지에서 $\dot Q = F_{A0}\sum\Theta_iC_{Pi}(T_{exit} - T_{cool})$만큼 열이 빠져 $T$가 내려간다. X-T 평면에서 수평으로 왼쪽으로 이동한다.Molar flows do not change, so $X$ stays constant, and the energy balance removes $\dot Q = F_{A0}\sum\Theta_iC_{Pi}(T_{exit} - T_{cool})$ so $T$ falls. On the X-T plane the state moves horizontally to the left.
What If?
만약에?What If?
만약 n-부탄 공급에 불활성 i-펜탄을 더 많이 섞으면?What if more inert i-pentane is mixed into the n-butane feed?
클릭하여 확인 →Click to reveal →
$\sum\Theta_iC_{Pi}$가 커져 같은 전환율에서의 온도 상승이 줄어든다. 발열 가역 반응에서는 온도가 덜 올라가므로 평형 전환율이 높아진다. 그러나 반응물 농도가 낮아져 같은 전체 공급량에서 부피가 커진다. Figure 11.3의 모델에서 $T_0 = 330$ K, X = 0.7에 필요한 부피는 i-펜탄 0%에서 2.5 m$^3$, 50%에서 4.3 m$^3$이다.$\sum\Theta_iC_{Pi}$ grows, so the temperature rise at a given conversion shrinks. For a reversible exothermic reaction the temperature rises less and the equilibrium conversion is higher. However, reactant concentration drops and the volume grows at the same total feed. In the Figure 11.3 model at $T_0 = 330$ K and X = 0.7, the volume needed is 2.5 m$^3$ at 0% i-pentane and 4.3 m$^3$ at 50%.
만약 반응이 흡열이고 반응기가 단열이면?What if the reaction is endothermic and the reactor is adiabatic?
클릭하여 확인 →Click to reveal →
전환율이 오를수록 온도가 내려가고 $k$가 작아져 반응이 느려진다. Figure 11.1에서 $\Delta T_{ad}$를 음수로 두면 단열 전환율이 등온보다 낮게 머문다. 공급 온도를 올리거나 단 사이에 가열기를 두어 온도를 되돌려야 한다. 가솔린 개질 공정의 이동층 반응기가 이 방식으로 단 사이를 가열한다.As conversion rises, temperature falls and $k$ shrinks, so the reaction slows. In Figure 11.1, a negative $\Delta T_{ad}$ keeps adiabatic conversion below isothermal. Raise the feed temperature or place heaters between stages to restore the temperature. The moving-bed reactors of gasoline reforming heat between stages this way.
만약 공급 온도를 650 K까지 올리면?What if the feed temperature is raised to 650 K?
클릭하여 확인 →Click to reveal →
속도는 매우 빠르지만 평형 전환율이 낮아 입구 근처에서 평형에 닿고 더 오르지 않는다. Figure 11.6의 기본 설정에서 출구 전환율은 0.10에 그치고 최적 온도(약 430 K)의 0.47보다 훨씬 낮다. 촉매를 더 넣어도 평형 전환율이 상한이라 개선되지 않는다.The rate is very fast but the equilibrium conversion is low, so equilibrium is reached near the inlet and conversion no longer rises. In the Figure 11.6 default setting the exit conversion is only 0.10, far below 0.47 at the optimum (about 430 K). Adding more catalyst does not help because equilibrium conversion is the upper bound.
Key Takeaways
01
에너지 수지는 알고리즘의 다섯째 단계Energy Balance as Step Five
$k(T)$와 $K_C(T)$가 온도에 의존하므로 몰 수지, 속도식, 화학량론에 에너지 수지를 더해 $X$와 $T$를 함께 푼다.Because $k(T)$ and $K_C(T)$ depend on temperature, the energy balance joins the mole balance, rate law and stoichiometry to solve $X$ and $T$ together.
02
단열 반응기의 T와 XT and X in Adiabatic Reactors
$\Delta C_P = 0$이면 $T = T_0 + (-\Delta H_{Rx})X/\sum\Theta_iC_{Pi}$로 온도가 전환율에 대해 직선으로 변한다. 반응열은 $\Delta C_P$ 기울기로 온도에 의존한다.If $\Delta C_P = 0$, $T = T_0 + (-\Delta H_{Rx})X/\sum\Theta_iC_{Pi}$ and temperature is linear in conversion. The heat of reaction depends on temperature with slope $\Delta C_P$.
03
단열 평형 전환율과 단 나누기Adiabatic Equilibrium and Staging
$X_{EB}$와 $X_e$의 교점이 한 단에서 얻을 수 있는 최대 전환율이다. 이보다 높이려면 공급 온도를 낮추거나 단 사이를 냉각한다.The intersection of $X_{EB}$ and $X_e$ is the maximum conversion from one stage. To go higher, lower the feed temperature or cool between stages.
04
최적 공급 온도Optimum Feed Temperature
고정된 촉매량에서 낮은 $T_0$는 속도가, 높은 $T_0$는 평형이 전환율을 제한한다. 둘이 균형을 이루는 $T_0$에서 출구 전환율이 최대이다.At fixed catalyst mass, low $T_0$ is limited by rate and high $T_0$ by equilibrium. Exit conversion is maximal at the $T_0$ where the two balance.